Question about Office Equipment & Supplies

Open Question

How to fix SC 28-01 of Bizhub Pro C500? How to

How to fix SC 28-01 of Bizhub Pro C500? How to adjust the "high pressure Unit"?

Posted by on

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

acdr
  • 1913 Answers

SOURCE: error code 29-16 on minolta

connect your printer us b cable again to computer.
also check there is not any paper jam on printer.
also refix cartidgev again.if problem remains check u installed driver properly.download driver from here and remove first old driver then install printer driver from here.
press power buttton for 10 seconds.also refix your ram after clean dust from it.

Posted on Nov 27, 2008

  • 1294 Answers

SOURCE: I have konica mionolta bizhub pro c500 when i

The problems is into fuser unitmCheck the thermistors,thermofuses,heater lamp and the rapis fuse.

Posted on Aug 05, 2009

hamzaskilltd
  • 316 Answers

SOURCE: HELLO SIR BIZHUB PRO C500 ERROR CODE SC 29-06 AND

Normal 0 false false false MicrosoftInternetExplorer4 /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin:0in; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:10.0pt; font-family:"Times New Roman"; mso-ansi-language:#0400; mso-fareast-language:#0400; mso-bidi-language:#0400;} Fuser problem, Warm-up incomplete

Posted on Jun 07, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Bizhub pro c500 error sc32-07


Printer control board (PRCB)
Paper exit fan /1 (M61)
Paper exit fan /2 (M62)
Paper exit fan /3 (M63)
Note:
• Since the old type is not
installed with the M61, M62
and M63, be sure to check
to see if the 25 DIPSW is set
as shown below:
Old type: DIPSW 21-0-0



have a tech check this problem

Feb 15, 2015 | Konica Minolta Bizhub Pro C500

1 Answer

Error sc 33 01


fuser code reset in service 25 mode.

Jun 04, 2014 | Konica Minolta Bizhub Pro C500

1 Answer

Scanner settings Bizhub Pro C500


The communication can only be complete when the IP Address is fully established. This is in the manual and information on doing a set up is detailed by Minolta. Only you or a technical person with privileges who you invite into your computer can resolve that issue.

Feb 20, 2014 | Konica Minolta Bizhub Pro C500

1 Answer

Error code sc 30-02


Can you tell me your detail questions ?

Jul 21, 2013 | Konica Minolta Bizhub Pro C500

1 Answer

Code sc35-02 on biz hub pro c500


My Bizhub pro 920 Error Code SC35-02

Apr 21, 2013 | Minolta bizhub 200 Copier

1 Answer

Konica minolta bizhub pro c500 sc code 45-20


READ THIS FIRST BEFORE DOING ANYTHING. Pull out middle section, then remove the mid section by pulling the big handles. Now on the left side of the unit is the Transfer belt, on the same side inside the machine across from the belt is a assy. which has three sensors on it, there are covered bye metal shield each it its own solenoid. You going the clean the sensor HOW??? from the right side of the machine stick you arm inside the and take clean rag and gentle raise and clean each sensor bet gentle see the springs on the shield do not want to have them fall off. DO NOT I mean DO NOT PLACE ANY PRESSURE WHAT SO VERY ON THE FOUR SHAFT IN SIDE THE MACHINE YOU BEND THE SHAFT EVEN SLIGHTLY throw away the hole machine because it will cost you a lot of money those fore shaft are what the drums ride ON. Then run gradation adjustment. If this does not work when was the last time a full PM was done? Might have to have the Transfer belt cleaning blade assy. cleaned, ore worse case the Registration Assy. that is what the three sensor are sitting on. is bad.

Jul 20, 2011 | Minolta Office Equipment & Supplies

1 Answer

HELLO SIR BIZHUB PRO C500 ERROR CODE SC 29-06 AND SC23-09


Normal 0 false false false MicrosoftInternetExplorer4 /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin:0in; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:10.0pt; font-family:"Times New Roman"; mso-ansi-language:#0400; mso-fareast-language:#0400; mso-bidi-language:#0400;} Fuser problem, Warm-up incomplete

May 10, 2010 | Minolta bizhub 200 Copier

1 Answer

ERROR CODE SC45-20


HAVING A REPORT CODE SC 45-20 HOW TO SOLVE IMMEDIATELY FOR PRINTER/COPIER BIZHUBPRO C500

Feb 11, 2009 | Konica Minolta bizhub C250 All-In-One...

Not finding what you are looking for?
Office Equipment & Supplies Logo

Related Topics:

82 people viewed this question

Ask a Question

Usually answered in minutes!

Top Office Equipment & Supplies Experts

kakima

Level 3 Expert

102366 Answers

k24674

Level 3 Expert

7993 Answers

yadayada
yadayada

Level 3 Expert

74896 Answers

Are you an Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...