Question about Black & Decker Drills

Open Question

How do I replace the chuck in my Black & Decker SSL20 Drill/Driver?

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 12 Answers

SOURCE: Dewalt Drill DC728. Chuck came out of drill body

If you find that the end of the screw inside the chuck is actually broke then you have a gear problem inside your drill. This is actually a very common problem. Sometimes people push too hard on their drills and the gears inside wear out and break. This prevent the motor from wearing out, but, the gears have to be replaced.
If it is the gears and not the chuck. you broke the minimium of the front gear or gears inside your drill. YOU CANNNOT repair gears. they need to be replaced. you may be able to find some off brand gears to work but, you run the risk that they are not as strong as your original ones, or may not be exactly grooved correctly.
so, if replacing your chuck does not work. find replacement gears. IF you cannot find the gears from the manufacturer see about replacing your drill.
If the chuck is still good, keep it. If you buy the same model, keep your old drill for replacement parts, ie, switch, armature, cord, etc.
hope this helps somewhat.

Posted on Jun 11, 2009

Ad
  • 16 Answers

SOURCE: HOW DO I LOOSEN A KEYLESS CHUCK TO REMOVE A DRILL

Keyless chucks normally have a knurled ring at the base of the chuck that you hold in one hand while turning the large knurled taper with the other. If the chuck has been overtightened, and you cant open like this, try using two stilson wrenches (Pipe wrenches) one on each of these parts. Use a soft cloth in the jaws to avoid damaging the knurling. You can also try some Q20 or similar into the chuck to help lubricate it.

Posted on Jun 15, 2009

  • 14 Answers

SOURCE: Keyless Chuck how do you change the bit? Model

hold outside collar on chuck firmly with your hand and reverse drill

Posted on Aug 02, 2009

  • 583 Answers

SOURCE: Cordless Drill, Keyless Chuck stuck in full open position.

if chuck is wide open ,look down inside there should be an allen screw or bolt at the bottom of the chuck it should undo anti clocwise and the chuck comes off

Posted on Aug 18, 2009

woobie dog
  • 1273 Answers

SOURCE: Black and Decker Cordless Drill Chuck stuck in full open position

I'd put penetrating oil in it and tap the chuck with a plastic hammer. That should free it up.

Best rgrds, W/D

Posted on Aug 18, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to remove a dr200 BLACK & DECKER 3/8" DRILL CHUCK, no chuck screw in chuck


Hi- We have instructions on how to remove the chuck listed on our website Q&A. I have included the link. Please use the instructions for the Keyed chuck. blackanddecker com


Thanks Black + Decker Customer Care

Mar 18, 2015 | Black & Decker Drills

1 Answer

The chuck on my drill willnot turn in either direction


The same thing happened to me. I found the carbon bar that contacts the motor had broken and it was jammed. For around $25 I got a new motor and replaced it. The unit I had was a Black & Decker.

Aug 04, 2014 | Black & Decker 18V Cordless Drill/Driver

2 Answers

12 volt black and decker keyless chuck will not close. Model CD120G


Try giving the inside a spray with WD40 then try closing the chuck. Check that there is not a left handed screw in the center of the chuck that has become partialy unscrewed. The chuck can jam open and just need a strong gril to release it. If the outer sleve of the chuck is turning but nothiing happens then you will need to get the chuck replaced.

Jun 10, 2012 | Black & Decker 18V Cordless Drill/Driver

1 Answer

The chuck is frozen on my 14,4 Black and Decker cordless drill. This is the second time that has happened with a Black and Decker drill so I assume it is a product defect. In use it was not that...


Hi,

Yes, they are an inferior product. However you can replace the B & D chuck with a Jacobs chuck that will hold up and last for a long time!

Jacobs Chuck

heatman101

May 23, 2011 | Black & Decker Drills

1 Answer

I have a Black and Decker 18 V drill .I opened the bit up to its largest opening and now cannot get it to budge. It is a keyless chuck. thanks, RW The model# iis CD180GS


I have had that same issue -- I just get a pair of channel locks and clamp onto the chuck ( not hard ) and run the drill forward -- this should close the teeth.

c...

Dec 31, 2010 | Black & Decker 18V Cordless Drill/Driver

1 Answer

I have a Black & Decker 18V cordless drill with keyless chuck. The spot where the drill bit fits is in the open position stuck and won't turn in either position. What am I missing how to unlock it?


Look at the three jaws in the chuck,if on is further out than the others the you need to tap ti back into place with a small punch and a hammer.If this does not work then you need to replace the chuck,remove the screw at the bottom of the chuck[where you put the bit],then you will need to to clamp vise grip on the chuck and with it pointed away from you hit the vise grips with a hammer with a sharp blow downward and it should come off.Hope this helps.

Jun 12, 2010 | Black & Decker CD9602SB 9.6 Volt Cordless...

1 Answer

How do replace a chuck on a black-decker cordless drill


you must open the chuck all the way and the screw is in the back inside the chuck this is a left screw which means its righty loosey and lefty tighty; unlike normal righty tighty and lefty loosey.

Mar 29, 2010 | Black & Decker 18 Volt Cordless Drill...

1 Answer

How do i release a drill bit


This particular drill/driver has a keyless locking chuck. Apart from suggesting you read the manual, you grip the black plastic part of the chuck and turn it anti clockwise (when it's facing you)

Oct 03, 2009 | Black & Decker 14.4v Cordless Lithium...

1 Answer

Black and Decker Cordless Drill Chuck stuck in full open position


I'd put penetrating oil in it and tap the chuck with a plastic hammer. That should free it up.

Best rgrds, W/D

Aug 18, 2009 | Black & Decker Drills

1 Answer

Keyless Chuck how do you change the bit? Model


hold outside collar on chuck firmly with your hand and reverse drill

Jul 10, 2009 | Black & Decker 3/8" Variable Speed...

Not finding what you are looking for?
Drills Logo

Related Topics:

49 people viewed this question

Ask a Question

Usually answered in minutes!

Top Black & Decker Drills Experts

Doctor PC
Doctor PC

Level 3 Expert

7733 Answers

JOHN LAPIER

Level 3 Expert

2428 Answers

yadayada
yadayada

Level 3 Expert

76164 Answers

Are you a Black & Decker Drill Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...