Question about Toshiba e-Studio 161 Copier Copier

Open Question

Toshiba e-studio 161 c2 error - Toshiba e-Studio 161 Copier Copier

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

didi2005
  • 524 Answers

SOURCE: Drivers for TOSHIBA e-studio 161 MFP for VISTA 64 Bit O.S.

What kind of interface u're using ? USB cable or network cable?
if USB cable, currently only support until Vista 32bits.
But if running networking, Vista 64bits is supported.

Posted on Mar 31, 2009

didi2005
  • 524 Answers

SOURCE: Can't print or copy with my toshiba e studio 161

H2 indicates thermistor open.

U can enter simulation mode and input "14" to clear the message.

If happen again, u need to check following:
Thermistor
Control PWB
Fusing section connector disconnection
The fusing unit is not installed.

Perform the following procedure to enter the simulation mode.
"C" key AUTO/TEXT/PHOTO key
"C" key AUTO/TEXT/PHOTO key
Main code Start key Sub code Start key
(Note:Perform the first four key strokes quickly allowing no more than one
second between key strokes.)


Posted on Apr 06, 2009

  • 4 Answers

SOURCE: toshiba e-studio161 - windows7 64 bit

For Vista there is only a 32-bit driver. I've already tested, it doesn't work

Posted on Dec 09, 2009

  • 1 Answer

SOURCE: toshiba e-studio 161 error code H2?What reset

does not solve these problems H2? substituted for the other thermistors, but still nothing same error ... The whole problem of the scheme not remove the plug from the power supply and printer cable recorded the error, which now does not solve ... help ??????

Posted on Jan 18, 2010

  • 30 Answers

SOURCE: TOSHIBA E-STUDIO 161 error code

Hi,
How are you this is jack my id jack_pak@hotmail.com
your copier toshiba 161 show H...4

Dear, Follow the procedure.... press C(CLEAR) BUTON+ PHOTO BUTON+C BUTON+PHOTO BUTON..... Your copier enter special mode
Then you press 14 and start key.... copier ...ok
PLEASE VOTE ME
Thanks,
Best Regards,

Posted on Sep 07, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

In toshiba 161 photocopier f5 error indicats


http://www.copytechnet.com/forums/toshiba/79285-e-studio-161-f5-02-error-code.html

Mar 12, 2016 | Toshiba e-Studio 161 Copier Copier

1 Answer

E studio 161 does not work with windows 7 please help I have driver of windows xp


Hi,
Toshiba e-studio 161 drivers are available Toshiba Official Support
Click 'Support & Drivers' (Top Right Corner)
From the page that appear Choose B/W Copiers
then Choose e-Studio 161
Select the drivers and download for your Operating System (i.e. Windows 7)
Also, Below is the direct download link for Windows 7 Drivers
E-studio Drivers for Windows7 (32Bit)

Hope it helps! Good Luck! Thanks for using Fixya!
CreativeTECH

Jun 28, 2011 | Toshiba e-Studio 161 Copier Copier

1 Answer

I have H2 flashing on my Toshiba e-studio 161 copier


h2 error is the fuser unit is faulty check and replace heater lamp thermo fuse and thermistor

Mar 07, 2011 | Toshiba e-Studio 161 Copier Copier

3 Answers

TOSHIBA E-STUDIO 161 error code show mw H and 4


Hi,
How are you this is jack my id jack_pak@hotmail.com
your copier toshiba 161 show H...4

Dear, Follow the procedure.... press C(CLEAR) BUTON+ PHOTO BUTON+C BUTON+PHOTO BUTON..... Your copier enter special mode
Then you press 14 and start key.... copier ...ok
PLEASE VOTE ME
Thanks,
Best Regards,

Aug 31, 2010 | Toshiba e-Studio 161 Copier Copier

2 Answers

I have a Toshiba e-studio 150 copier. L-1 error code flashing


hi there is problem L-1 means that u have problem CCD MCU Harness Disconnect

May 12, 2010 | Toshiba E-Studio 161 Copier

2 Answers

Toshiba e-studio 161 error code H2?What reset problems?


does not solve these problems H2? substituted for the other thermistors, but still nothing same error ... The whole problem of the scheme not remove the plug from the power supply and printer cable recorded the error, which now does not solve ... help ??????

Jan 12, 2010 | Toshiba e-Studio 161 Copier Copier

2 Answers

Error h4


H4 in 161, fuser low temp.; instantly solve it by simulation (c-auto-c-auto) 14; check thermistor; check fuser lamp by 5-02. it is to blink!

Jul 07, 2009 | Toshiba e-Studio DP170F Plain Paper Laser...

1 Answer

SUL DISPLAY DELLA TOSHIBA E-STUDIO 161 LAMPEGGIA ERRORE L6 COSA D


hi i have problem with printer toshiba e-studio161
what's doint?

Apr 06, 2009 | Toshiba e-Studio 161 Copier Copier

Not finding what you are looking for?
Toshiba e-Studio 161 Copier Copier Logo

Related Topics:

30 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toshiba Office Equipment & Supplies Experts

Branko Djurdjevic
Branko Djurdjevic

Level 2 Expert

102 Answers

CheckitRight
CheckitRight

Level 3 Expert

1362 Answers

pkwc

Level 2 Expert

254 Answers

Are you a Toshiba Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...