Question about Masterbuilt ESQ30B Smoker

Open Question

Meat probe not working, reads over 400 - Masterbuilt ESQ30B Smoker

Posted by Anonymous on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to calibrate kenmore meat probe? it says 170degrees when plugged in cool.


170 degrees is likely the minimum it can read. put a container of water in the oven, put the probe in the water, and set the oven for 250 degrees. Watch the probe, and see what temperature it shows when the water boils. Depending on your altitude, it should be 212 or a little less.

Sep 04, 2014 | Kenmore 30 in. Freestanding Induction...

1 Answer

F3E3 Meat probe Shorted


faulty meat probe, probably a factory defect, if still covered by warranty, return oven for replacement.

Mar 22, 2014 | Jenn-Air 27 in. Electric Single Wall Oven...

1 Answer

I used my Polder meat thermometer in my gas grill. The fat off the meat cause flames to touch the probe. When I looked at the read-out it said 406 degrees F and then HI degrees F. Now it just reads HI...


It is possible that the therrmometer has over shot the limit set on it .It can be spoiled because the hat was in direct contact with the probe and has resulted in the failure of the unit.

Aug 27, 2010 | Microwave Ovens

1 Answer

My oven is stuck in probe mode and will not cancel.. what should i do


Measure the resistance of the meat probe on the K-ohm setting. If it's open, then the probe is bad. I'm not finding a spec on the resistance but it should be something in the K-ohm range.

Next stop is to check the meat probe socket. May be gunked up with condensed grease or whatever. Sometimes a light schmear is all it takes to flake it out. Then check continuity from each leg of the meat probe socket back to the ERC, where the meat probe harness connects.

Mar 06, 2010 | Ovens

3 Answers

What is a U80 meat probe error and how do I fix it?


Error U80: Shorted meat probe

1) Food, moisture, or other substance is in the socket or on the oven connection end of the meat probe. Check: Verify proper operation with new probe (replace probe). If still fails with new probe check wiring of housing to eliminate shorting to sheet metal. Solution: Clean socket and meat probe.

2) Bad meat probe (shorted). Check:Use new meat probe to test for correct values in the service screens. Solution: Replace meat probe.

3) Shorted socket or wiring. Check: Test socket at connector J20 on relay board. Solution: Replace meat probe socket.

Functionality when error U80 reported: Cooking and cleaning are available but meat probe options will not be available.

User action/solution:
1) Verify oven connection end of meat probe is clean and no food, moisture or other substance in is the meat probe socket.
2) Call for service.

Aug 26, 2009 | Dacor Epicure EO230 Stainless Steel Oven

1 Answer

I have a Sunbeam digital meat probe thermometer used once. Now the display for thermo/temp comes up H instead of the temperature of the meat. What is wrong? Sunbeam digital meat probe thermometer has quit...


I left mine in a hot tub for well over an hour. It started reading room temp at about 125 degrees. It worked for me to put the thermometer in the freezer until the readings were correct. hope this works for you.

Feb 22, 2009 | Sunbeam 2370 MixMaster Series Stand Mixer

1 Answer

I have a Sunbeam digital meat probe thermometer used once. Now the display for thermo/temp comes up H instead of the temperature of the meat. What is wrong?


I have the same problem. The problem is the probe went bad. I had a friend with another sumbeam digital probe (the mavrick) put that probe into mine and the temperature reading was working properly. So, now I am looking for a replacement probe. but looks like I will have to just buy another digital meat probe.

Aug 16, 2008 | Sunbeam 4214 Iron

Not finding what you are looking for?
Masterbuilt ESQ30B Smoker Logo

Related Topics:

61 people viewed this question

Ask a Question

Usually answered in minutes!

Top Masterbuilt Grilling Experts

Dan Webster
Dan Webster

Level 3 Expert

8220 Answers

Brad Brown

Level 3 Expert

15557 Answers

paulcarew

Level 3 Expert

2461 Answers

Are you a Masterbuilt Grilling Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...