Question about Craftsman 2700 PSI Briggs Stratton Powered Pressure Washer

Open Question

Where is primer button in 580.752951 pressure washer

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Does not have a choke. how do i start it?


does it have a primer bulb
if so press it several times until you feel a slight resistance
open the throttle up and pull the cord
the primer bulb squirts a set amount of raw fuel directly into the manifold

Nov 01, 2015 | Troy-Bilt XP 2800 PSI 2.5 GPM Gas Pressure...

1 Answer

Where is the choke on a Brigg-stration model 580-752920 engine?


Hello,
This particular model is called a readystart engine, they do NOT have a primer or choke, if you are having fuel troubles starting there could be a blockage in the carburettor or fuel filter.

Hope this helps

Brad

Jul 28, 2014 | Craftsman 2700 PSI Briggs Stratton...

1 Answer

Husky washer engine only runs off the primer fuel


hello,remember,it has to create vacuum [suction] to draw fuel in,the very fact you are using the 'primer' proves that it is only a fueling problem,and is simply not 'drawing in fuel on it's own.check that there are no 'crud' build up beyond the needle valve,is the air supply restricted?as no air in, 'NO FUEL'! recheck the list again,you will discover[happily] that you were on the verge of 'cracking it' best of luck, cheers.

Jun 02, 2014 | Garden

1 Answer

Hello my question is on my powerwasher the primer rubber button has like melted away how would that be replaced


You need to go to a small engine repair center to find the primer bulb that fits on your motor. It will depend on what motor and carburator you have. They are fairly easy to replace. The primer bulbs 'melt' or go soft because of ethenol in gas. You should expect to get one to two years out of a bulb so you may want to get an extra or two.

Dec 26, 2012 | Briggs & Stratton Gas Pressure Washer...

1 Answer

Fires up good but dies out?


you have a plugged primary jet in the carb

Aug 04, 2012 | Briggs & Stratton 3000 PSI Pressure Washer

1 Answer

My washer will start but only run for a few seconds......unless you hold the primer bulb in


The primer bulb has a pin hole in it:
This is what you need:
http://www.mymowerparts.com/partdetail/1079/14606.php

All local lawn mower repair / parts sources have this part in stock. This is a common issue with primer bulbs that you have to hold the bulb in so that it will run. When you do that your stopping it from drawing air through the hole in the primer bulb so it operates normally. Replace the primer bulb and it will be fine.

Thanks for choosing FixYa,
Kelly.

Aug 14, 2011 | Briggs & Stratton Gas Pressure Washer...

1 Answer

How do you prime a troy bilt 675 pressure washer


if you dont see a primer bulb then you must start it in choke mode after running out of fuel

May 31, 2010 | Garden

1 Answer

I can't start my powerwasher. Where is the choke?


This Power washer has a 3.75 hp Briggs and Stratton Engine. It does not have a choke but does have a primer bulb. You must depress the primer bulb at least 3 times to start the engine. The primer bulb is on the side of the carb. It can be black or red. If your still unable to locate the primer bulb please provide your ENGINE model number and I will provide you a link to a diagram for the location of the primer bulb.

Thanks for using FixYa.

Kelly

May 29, 2010 | Briggs & Stratton Gas Pressure Washer...

1 Answer

Engine wont stay running


It is a diaphram carb. Doe's the primer **** straight gas or does it have air bubbles in it? If it has bubbles in it then it is a leak in the fuel line.
If not then Unhook the intake fuel line and pump the bulb until all of the gas is out of it. Then pour the gas out of the tank and rinse it out with new gas. Pour in new gas and it should be ok.

May 23, 2010 | Briggs & Stratton Power Products 1539...

2 Answers

Pressure Washer Engine will not stay running


My Kracher 2500 pressure washer has no pressure unless I remove the nozzle. If, I remove the nozzle and pump the trigger several times and quickly replace the nozzle it works fine until I release the trigger. Karcher (online) suggested I remove and clean the unloader which I did. It still doesn't work correctly. What another solution?

May 29, 2009 | Garden

Not finding what you are looking for?
Craftsman 2700 PSI  Briggs Stratton Powered Pressure Washer Logo

Related Topics:

147 people viewed this question

Ask a Question

Usually answered in minutes!

Top Craftsman Garden Experts

Wade Mobley
Wade Mobley

Level 3 Expert

489 Answers

Dean Gruber

Level 2 Expert

110 Answers

Roland W VanLue
Roland W VanLue

Level 3 Expert

486 Answers

Are you a Craftsman Garden Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...