Question about Whirlpool Calypso GVW9959K Top Load Washer

1 Answer

Keep getting SL error code

The washer does not finish the spin cycle....washer stops while trying to spin, get SL on error code and the fabric softener is still in fill reservoir when washer stops....any sugestions?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 447 Answers
Re: keep getting SL error code

SL is a suds lock code it can be caused by the drain pump not draining the water, too much detergent, non HE detergent, or extra heavy loads, try running it empty, if code persits it is a computer failure

Posted on Sep 28, 2007

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

Kenmore Front Load Washer won't complete cycle F06

Have you cleaned your machine lately? They make an in wash boost- it gets rid of the extra suds built up inside the machine that you cant see but your machine detects it and causes faults such as that. Also, there is a small wire on the control board that may need replaced if it keeps kicking the error code.

Apr 07, 2016 | Kenmore Elite 45986 Front Load Washer

1 Answer

My Maytag Neptune FAV6800AW top load washer will not go into the spin cycle with clothes in it. It stops at 12 minutes and then we get a DC error code. When you take the clothes out, it finishes up the...

if it spins when you remove the wieght out of the tub i'd change the belt and if that's not the problem the tranny is bad but try the belt first,most likely that's what it will be,stop overloading the washer the part number for the belt is 25001054 and it's around 15 bucks

Oct 22, 2010 | Maytag Neptune FAV6800AW Top Load Washer

1 Answer

Indesit Evolution W16s washing machine H20 error code

if there a advance cycle button push it an see if the timer will advance to spin if not turn the power off to washer an wait a couple mintue an the door will open

Apr 24, 2010 | Washing Machines

2 Answers

Maytag neptune FAV6800AWW top load washer gets to 32 minutes left and goes no further. It starts to cycle for about 5 seconds and stops for about 35 seconds... over and over and over

Is the machine in Spin Cycle when this is happening? What part of the washer selected cycle does the Cycle Status LED say the machine cycle is in.
If it’s in the Spin Cycle I think you have a clutch issue. Do you take any error codes to the LED console display such as dC or uC?
If you stop the machine in that cycle and do a Spin Only cycle will it complete?
Do you want to DIY the fix? Let me know and I will try to help…..Rich

Feb 26, 2010 | Maytag Neptune FAV6800AW Top Load Washer

1 Answer

My washer stops before the rinse cycle because it can't seem to drain enough to start the spin cycle. I just had the drain motor replaced one month ago. I get the error code nd. I can sto the cycle and...

I'd love to say yes! The machine is stopping because it will not drain. This is what the nd code means. Therefore, it will not rinse (add more water) or spin because the water level is already too high and to try to "spin it out" would put too much pressure on the machine with that much water in it. Drain out the water by putting the drain hose below the level of the washer (this takes forever) and call your repair man back!

Feb 18, 2010 | Maytag MAH8700A Front Load Washer

4 Answers

We have a Whirlpool duet washer that doesn't finish washing

its probably a blocked water filter to this fabric water valve or the coil has failed on the valve,it should be 3800kohms,check the filter at the water inlet connection,hope this helps

Jan 08, 2010 | Whirlpool Duet GHW9150P Front Load Washer

1 Answer

The washer goes through the whole cycle then for the last 11-12 min it stops and doesn't finish the rinse cycle. it sprays water just like at the begining of the cycle then tries to spin then pauses

With no error code on your FAV6800AW or FAV9800AW I will still give it shot. I believe you are failing in spin cycle. See this Post and the post I link to for a step by step clutch maintenance/repair. If you have more info on the failure or questions post back and we will try to help.

Sep 23, 2009 | Maytag Neptune FAV6800AW Top Load Washer

1 Answer

The machine stops after the wash cycle and won't finish.

The code is UE

load too small.
• Load is out of balance.
• The washer has an imbalance
detection and correction
system. If individual heavy
articles are loaded (bath
mat, bath robe, etc.) and the
imbalance is too great, the
washer will make several
attempts to restart the spin
cycle. If an imbalance is still
detected, the washer will stop
and the error code will be
• Add 1 or 2 similar items to help balance the load.
• Rearrange items to help balance the load.

please rate this help to keep the service online

Aug 20, 2009 | LG Washing Machines

Not finding what you are looking for?
Whirlpool Calypso GVW9959K Top Load Washer Logo

1,213 people viewed this question

Ask a Question

Usually answered in minutes!

Top Whirlpool Washing Machines Experts

Dan Webster
Dan Webster

Level 3 Expert

8147 Answers

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Mike Cairns
Mike Cairns

Level 3 Expert

3053 Answers

Are you a Whirlpool Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides