Question about Bosch Classixx WFO 2866 Front Load Washer

1 Answer

All the lights are flashing and nothing happening. Powered off and on again. How do I reset the board??

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Passionate:

    Visited the website for 10 consecutive days.

  • Expert
  • 114 Answers

If all the lights are flashing it is without a doubt a faulty main board. If only certain lights are flashing it is showing an error code. Tell me which lights are flashing and will point you in the right direction. Approximately will cost 100 to 140 for a board, which also has to be programmed

Posted on Oct 19, 2013

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

When I put my printer on, both the red 'on' light and the 'green' problem light are flashing intermittetly . I have tried to reset the printer by pressing the 'green light' down for a few seconds..but...


when I put my printer on, both the red \'on\' light and the \'green\' problem light are flashing intermittetly . I have tried to reset the printer by pressing the \'green light\' down for a few seconds..but nothing now happens on this mode. I have also turned the printer off and back on again, and lastly took the power cable off and back on again..and still no joy..any ideas

Nov 02, 2010 | Epson Stylus C46 InkJet Printer

2 Answers

Vacum cleaner flashes lights and goes dead.


Do you put it down before you turn it on? some vacs wont turn on in the upright position. Happened to me once til I stepped on the button to bed it back then powered right up.

Jan 15, 2010 | Electrolux Vacuums

1 Answer

Phonic k-12 powered mixer Nothing happens when I press the power


Hi...

Most new stuff has the fuse/fuses mounted in clips on the power supply board.
If yours is anything like the one a picked up for one of my bands, you can take the bottom plate off and see everything inside.
Look for where the AC cord goes after the power switch.
There should be a circuit board with a fuse or 2 mounted on it

Jul 01, 2009 | Audio Players & Recorders

2 Answers

Electrolux EWF 1087 - Power on, light goes orange, nothing works.


Hold reset and start buttons down, while turning on. Hold down for about 10 seconds.
If you're getting an E90 error code, which means communications error, it means you have a dodgy connection between the main board and the control panel.
Disconnect the power completely, open up the top of the machine and reseat the plugs on both ends on the blue ribbon cable connecting the front panel display to the main board. (The main board is the big white plastic thing with all the wires running into it).
Do the reset steps when turning on again, should be good to go, otherwise it's a bit more serious and you'll need the tech back.

Feb 28, 2009 | Washing Machines

1 Answer

U-Line Model ULN-CLR60B-00


call 1-800-779-2547, U-Line's tech support.

Has to be a bad a switch, wiring issue or maybe a control board. pull the service cover and see if the red light is lit on the board (or flashing). Light on (no flashing) indicates the board is powered up and no errors are occurring.

http://www.u-lineservice.com


Jun 09, 2008 | U-Line Icemaker

1 Answer

Kenmore HE 9t quiet pak


Sounds to me like the Main Computer has failed. F11 means it is not communicating with the Motor control Board. It has nothing to do with the door locks. Remove to lid of the machine to axcess Main control. Sometimes a tap or two on the board makes them work again for a short time. Leave unit powered down for a few mins to reset board.

Nov 24, 2007 | Kenmore 3.8 cu. ft. HE3 Front Load Washer

2 Answers

D101GGC JUST STOPPED


Hello Spawn11455,

Maybe you can try taking out the ram and reseating it back properly. If that doesn't work, then maybe you can reset the cmos settings. That is a little jumper near the cmos battery that you have to remove and place on pin 2 & 3 and then put back on pins 1 & 2.

Good luck,
Lolita

Nov 05, 2007 | Intel D101GGC Motherboard

Not finding what you are looking for?

Open Questions:

See all Bosch Classixx WFO 2866 Front Load Washer Questions

Bosch Classixx WFO 2866 Front Load Washer Logo

207 people viewed this question

Ask a Question

Usually answered in minutes!

Top Bosch Washing Machines Experts

Tim Whalen

Level 3 Expert

3074 Answers

yadayada
yadayada

Level 3 Expert

76164 Answers

Dan Webster
Dan Webster

Level 3 Expert

8220 Answers

Are you a Bosch Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...