Question about Dishwashers

2 Answers

Kenmore dishwasher When I push start on my dishwasher it does nothing. The lights work on the wash settings and the dry settings but when I push the start button, nothing.

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer
Re: Kenmore dishwasher

Thermador Fully Integrated Dishwasher (DWHD64CP) i just installed this unit myself i wired it up ran supply line it lights up i select a cycle i hear it humming but it will not start the cycle or if it is starting it is not getting water in the unit. i checked the water line and water is flowing to the unit. Any ideals? Thanks in advance!

Posted on Jul 19, 2010

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 447 Answers
Re: Kenmore dishwasher

Needs a new control panel/ touchpad assembly very easy solution!!!chat with me online and ill step you through it save up to $65 (my in-home rate in florida is $75!!!!!!!)

Posted on Sep 27, 2007

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

Kenmore dishwasher will not start

The most probable cause is the door latch (or switches in the latch) are not working right, and the controller thinks the door is open, even though it is closed.

Aug 13, 2012 | Kenmore Dishwashers

1 Answer

Kenmore Ultra Wash Model 665.1388 problem the normal wash green light is on heated dry light is on and the start resume light is flashing but wont startup helpppp

see your instruction manual and go to the section troubleshooting and fix it.
if you do not have the i.manual download for free or

see the diagram

God bless you

Jun 18, 2012 | Kenmore Dishwashers

1 Answer

Clean light is blinking, when you shut door and push start cycle nothing happens

Hello & Welcome to FixYa

Flashing clean light is reset by pressing two buttons in sequence 3-4 times, to reset your kenmore press these buttons in sequence:

High temp wash-heated dry-high temp wash-heated dry

Please get back to me if you have any other questions.


Mar 21, 2011 | Kenmore 24 in. 16039 Built-in Dishwasher

2 Answers

My Kenmore Ultra Wash Quiet Guard

take kick plate off get book out how to reset board

Apr 24, 2010 | Kenmore 15899 Built-in Dishwasher

2 Answers

Clean light keeps blinking and I can't start a new cycle

That is a comon problem with that model. It is not sensing a temperature change in the water.

Push i believe it is heated dry and sani rinse going back and fourth between the two to clear the code and see if you can get it to complete a cycle. If it doesnt call sears and schedule service there is a service flash repair that should not cost you anything to repair the unit.

Nov 13, 2008 | Kenmore 24 in. 15932 Built-in Dishwasher

1 Answer

Kenmore elite model 16574

press (high temp-wash) button and then ( heated dry)
do that 3 times in that order within 5 seconds. So it looks like this:

(high temp-wash) ( heated dry) (high temp-wash) ( heated dry) (high temp-wash) ( heated dry)

That will start a short diagnostic cycle (last about 2 minutes) that will clear the blinking light and allow you to use the dishwasher. If the light comes back, your drying cycle has failed and you will need service.

Oct 28, 2008 | Kenmore 24 in. 16352 / 16354 / 16359...

12 Answers

Kenmore ultra wash quiet guard 3 dishwasher problem

call sears, 1-800-4MY-HOME. They have a trouble-shooting department that will get rid of this problem. It is caused by water temperature being wrong at the start of the cycle.... blah, blah, blah. The representative will tell you to push a certain set of buttons in a certain order and that unlocks the dishwasher.

Sorry I don't know the sequence

Jun 08, 2008 | Kenmore 24 in. 15689 Built-in Dishwasher

2 Answers

Kenmore Ultra Wash Dishwasher LIghts are blinking....

I just read this for the same problem: push sanitize, then heat and dry, sanitize, heat and dry, sanitize, heat and dry, cancel, then open and close the door. It worked. The dishwasher is running correctly even as I type this. 

Feb 11, 2008 | Kenmore 24 in. 17262 Built-in Dishwasher

2 Answers

Kenmore Dishwasher displays the number "98"

I have a very similar problem. When I push a wash selection, every light on the panel shows up...and when I push Start, nothing happens. When I push cancel, it trys to drain, even tho no water is in there any more. Have you ever had an answer to your problem?

Feb 06, 2008 | Kenmore 16872 Built-in Dishwasher

Not finding what you are looking for?
Dishwashers Logo

Related Topics:

1,637 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dishwashers Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Mike Cairns
Mike Cairns

Level 3 Expert

3053 Answers


Level 3 Expert

4342 Answers

Are you a Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides