Question about Janome Sew Precise Mechanical Sewing Machine

1 Answer

Foot control only goes at very slow speed - Janome Sew Precise Mechanical Sewing Machine

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Cheetah:

    An expert who has answered 20 or more questions within one hour.

  • Expert
  • 84 Answers

Some Janome foot controls have a HIGH and LOW switch on the foot control. Check if your does.

Posted on Oct 20, 2013

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Repairman can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Repairman (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How do you change the speed on a typical sewing machine2603 ?


most sewing machines are controlled by a foot peddle the harder you press the faster it goes but if this one is electronic it should have another method of slowing it down

Feb 23, 2017 | Sewing Machines

1 Answer

Slow sewing regardless of speed setting


I'm thinking that the problem is in the foot control
take the foot control to a sewing machine repair shop and have it checked out
you say it appears aftermarket--probably is to replace a faulty OEM unit

Aug 22, 2016 | Janome Memory Craft 6500P / MC6500P...

2 Answers

Sewing machine slow in forward but fast in reverse


the speed is controlled by the foot pedal perhaps it needs replaced

Jul 04, 2015 | Sewing Machines

2 Answers

How do I slow the speed of the machine down in order to quilt


use a smaller stitch. DO NOT PUT YOUR FOOT ON THE PEDAL SO HARD

Jun 28, 2015 | Sewing Machines

2 Answers

What is the difference between a variable and non-variable speed sewing machine foot control?


variable foot control==the farther you push it...the faster the machine goes....
non variable....only has stop...and run....

Jun 05, 2015 | Sewing Machines

1 Answer

Karcher 630


The grease inside the foot controller is gone or dried up. Open it, clean it, and apply a little bit of new grease, Vaseline is fine. I shouldn't have to tell you to unplug it from the wall first.. should I?

Apr 26, 2014 | Singer Sewing Machines

2 Answers

Can not start at a slow speed with foot pedal need to now how to adjust start speed


THE FOOT PEDLE IS NOTHING BUT A REASTAT. A REASTAT IS A WIRE WRAPPED AROUND A CONDUCTOR THE WINDINGS START OUT FAR APART AND GET CLOSER TOGETHER THE FARTHER YOU PUSH THE PEDLE DOWN . THE FAR APART WIRES ARE THE SLOW SPEED THE CLOSER ONES ARE FASTER SPEED
THESE WIRES WILL WEAR OUT OVER TIME OR CORRODE OVER TIME AND CAUSE THIS PROBLEM. TRY SOME ELECTRICAL CONTACT CLEANER AND SPRAY THE FOOT PEDLE INSIDE ANY WHERE YOU CAN AND LET DRY. MOST CONTACT CLEANERS ARE NONE CONDUCTIVE AND DRY IN MINUTES

Aug 15, 2009 | Consew 206RB

1 Answer

No matter how hard I press down on the foot pedal my needle speed is super slow. The needle position indicator sometimes shows up when the needle is down and the needle continues it slow speed even when my...


is the machine easy to turn by handwheel? if not it may be seizing and needs servicing.

if the machine is free to turn by hand it sounds like your foot control is in need of repair or replacement - see a tech.

scott.

Jul 20, 2009 | PfaFF Sewing Machines

3 Answers

My machine has power, but foot pedal only makes needle go slowly


sounds like the contact in the foot peddle has failed try a new peddle

Jan 02, 2009 | Necchi 3101 Mechanical Sewing Machine

2 Answers

Foot pedal dead, machine keeps sewing!


There is no suppressor in the foot control of a 425. Only the control unit, which may need to be replaced. If the machine accelerates to full speed, it may have a problem with the "stop right" board which tells the machine whether to stop with the needle up.
You could have several problems, so go see a qualified Husqvarna repairman. You may contact Husqvarna customer service to locate the best one in your area.

Mar 12, 2008 | Husqvarna Freesia 425

Not finding what you are looking for?
Janome Sew Precise Mechanical Sewing Machine Logo

Related Topics:

59 people viewed this question

Ask a Question

Usually answered in minutes!

Top Janome Sewing Machines Experts

Tally Girl
Tally Girl

Level 3 Expert

1133 Answers

Douglas Plant
Douglas Plant

Level 2 Expert

191 Answers

Eva Hack

Level 1 Expert

25 Answers

Are you a Janome Sewing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...