Question about Nordic Track C2255 Console (treadmill)

1 Answer

After attaching key all lighs come on but none of the buttons work except foe pulse feature. also belt won't move.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Nordic Track Master
  • 12,223 Answers

Rests the treadmills, follow this steps and fix it. God bless you
replace old batteries ( if your system has batteries, clean the contacts batteries from oxide, dirty, etc) put a new one. Tight the ribbon cable inside the display board+tight the upper and lower connector too.

    • 1
Unplug the treadmill. Locate the console key and place the safety or reset key into the treadmill console. Replace any parts that need replacing, or is large enough to trigger with a pencil eraser or Q-tip. Plug the treadmill plug back into the wall. Use the Q-tip to press the reset button. It may be necessary to hold the reset button down for a few seconds. "CL11" will appear in the display of the treadmill.
    • 3
Press the reset button one more time with the Q-tip. "CL21" should appear on the screen. Press the enter key. The display will change again and show "CL22." Keep pressing the enter key until the numbers cycle through to the number "CL26." Press enter one more time. The letter E should appear on the display screen.
    • 4
Press enter twice more. The letters "SS" should appear on the screen. When this happens, press the start/stop key. Making sure to keep well away from the tread, press enter to start the treadmill. The treadmill will start on its own. The treadmill will stop on its own after a few seconds. When it stops, press the power key two times. Remove the safety key and put in a safe place. Your treadmill is reset.move on to the next step.
    • 2
Locate the reset switch on the underside of the treadmill console. Usually the button

Posted on Oct 19, 2013

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I fix the Royal Academy Electric Typewriter 1980's, when I have the power on, it works, but the keys doesn't work at all.


You may have a broken belt. They are no longer made but if you have a good hardware store you can get a long "O" ring and use it as a replacement.

DickyO

May 31, 2015 | Royal 1980s Academy Electric Portable...

1 Answer

Everything working except the belt


do you have the magnetic tag attached to you and the machine? it prevents operation unless its attached.

Jan 15, 2014 | Golds Gym Trainer 410 Treadmill

1 Answer

My Golds Gym trainer 480 treadmill wont start and none of the buttons work except for the up and down arrows for the incline.


my gold,s gym trainer 480 will ot run,everthing light up on console. could it be a fuse?

Oct 20, 2012 | Exercise & Fitness

1 Answer

Kenmore elite dishwasher mdl 665.16919001 all lighs out, won't come ont


try a simple step to reset unit unplug and then plug back in

May 26, 2012 | Kenmore Dishwashers

1 Answer

Galant won't turn over when trying to start. No spark from plugs. Changed crank sensor and timing belt and still won't start. Any suggestions


you now need to check for 12 volt power, and signal to the coil, also be sure all you timing marks are correct, if you have no spark, unplug one of the injectors and using an led test light check for injector pulse power across the two terninals while cranking, if you have no injector pulse then you could have a problem with the ignition passlock system, or key decoder

Jul 31, 2011 | 2005 Mitsubishi Galant

1 Answer

Hi. I have an old Brother electric typewriter 5713, which I want to sell. It all seems to be working fine except the hammers don't move when I press the keys. Quite an important feature! The hammers are...


Probably a broken belt and a stretched belt. Some of the brothers had a flat belt, you can try cleaning the belt with achohol and the pully it rides on.

Mar 14, 2011 | Brother Office Equipment & Supplies

1 Answer

When I turn on the pool, the pacer works for about 5 minutes then just gets stuck on the wall. If I turn off the pool and reset, it starts again then stops. How can I decrease the suction or adjust the...


You need to use the Pool Pulse feature to control the flow of water through the cleaner. Here is a brief overview, but if you need more details, consult page 6 of the users manual for this pool cleaner (below if you don't have it).
"Remove the cleaner head. Attach the Pool Pulse to the end of the hose and keep it under water. Turn on the filtration system.
• For pools with one skimmer, flow is automatically regulated by the Flowkeeper Valve. Insure the blue indicator of the Pool Pulse is in the ideal range (when viewed from the side).
• For pools with two or more skimmers, leave the selected skimmer open and slowly close the other skimmer(s) until the blue indicator of the Pool Pulse moves into the ideal range (when viewed from the side).
• For pools with a wall vacuum fitting, leave the wall vacuum fitting fully open and slowly close the skimmer valve until the blue indicator of the Pool Pulse moves into the ideal range (when viewed from the side).

Keeping the hose under water, remove the Pool Pulse. Submerge the cleaner head, and when the bubbles stop coming from the extension pipe, attach the hose end. Your installation is now complete."

http://www.baracuda.com/resources/manuals/PacerW83410.pdf

Dec 05, 2010 | Zodiac Pacer Pool Cleaner

Not finding what you are looking for?
Nordic Track C2255 Console (treadmill) Logo

248 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nordic Track Exercise & Fitness Experts

Matt Olenzek
Matt Olenzek

Level 2 Expert

293 Answers

Electro Med Services...
Electro Med Services...

Level 3 Expert

6694 Answers

Paul Sikkema
Paul Sikkema

Level 2 Expert

171 Answers

Are you a Nordic Track Exercise and Fitnes Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...