Question about Craftsman 42cc 18" Gas Chain Saw

1 Answer

Were can I buy a service repair manual on model 358.350870 18 inch bar I need to replace the fuel lines and fitting that goes in tank

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 13 Answers
Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replacing fuel disconect2004 dyna low rider


Hi Anonymous, attatch fuel supply line to the quick disconnect fitting, insert supply line into tank, screw in fitting to tank, torque fitting to 220 to 225 inch lbs. or 18 ft lbs. attach remaining end of fuel supply line to fuel pump pressure regulator. Good luck

Dec 25, 2013 | 2004 Harley Davidson FXDL - FXDLI Dyna Low...

Tip

Easy way to install fuel line and primer bulb return line into gas tank


Chainsaw fuel lines enter the gas tank from holes in top of tank. They are sized for a tight fit to prevent leakage. Make it easy on yourself when pushing the line through the tank by cutting a long lengthwise taper cut with razor knife 3 inches or longer to easily feed through that tight hole. Once started you will then have to grab it through the gas cap hole with needle nose pliers, then cut the tapered end flush and add fuel filter. Readjust inside length by pulling from above, then cut to length to upper carb fitting. If connecting to primer bulb a filter is not required and make sure the line goes to fitting on primer bulb marked tank.

on Nov 17, 2015 | Fuel Line & Primer Bulb Repair Kits 2...

1 Answer

How to repair fuel line on craftsman chain saw model number 358.360260 16 inch bar . how to do it .


Fuel lines are generally fixed by replacement of the fuel line because the rubber it is made of deteriorates from age and alcohol contained in gas. Before you begin, make a mental note or take a picture of how the fuel line runs from the tank to the carburetor so you will be able to put the replacement in the same position.
On most chainsaws you need to take some wire, make a u-shaped end, which will be used to grab the fuel filter in the fuel tank. Drain the fuel in the tank. Disconnect the fuel line from the carburetor. Generally there are two lines on the carburetor, one for fuel, the other line creates suction used to pump fuel and is connected to the motor, not the fuel tank . Just disconnect the fuel line, it is usually on the side of the carburetor and will leak gas when disconnected. Once this is done, using the wire, gently grab and pull the filter towards the filler opening and using needle nose pliers grab the fuel line above the filter and pull. The problem you may have, is if the fuel line is in bad shape it will break, But once you have the filter off the fuel line, the fuel line can be pulled out from either the inside of the tank or from where it comes out of the tank and goes to the carburetor. Once it is removed you are ready to put the new fuel line in.
It is best to put the fuel filter on the fuel line next. It easier than trying to put it on inside of fuel tank going out. Spray some WD40 or equivalent, on the outside of the gas line, to help the line squeeze through the whole in the back of the tank, which it will have the go through. From the outside of the tank, where the fuel line comes out, fish some wire inside the tank and put the fuel line on the end of it, making sure not to pierce or damage the fuel line. If needed a piece of black tape will hold the wire better and help fit the line through outside hole. Once the fuel line is on the wire, pull it through carefully out the other side of the tank. It is best to use your fingers to pull the line through the outside hole, it makes it less likely the line will get torn or overstretched as line goes through the hole because of the extra rubber used on the line to seal the tank from inside and outside. Once the line is pulled through and seated, run the other end to the carburetor and you are done.

Oct 01, 2013 | Husqvarna Craftsman 36cc, 16 In. Gas Chain...

2 Answers

Needing digram of furl tank andlines


I am sorry we have no such diagrams, they are in the factory service and repair manuals and those are copy protected. You can buy access here www.alldatadiy.com for a fee.

Oct 28, 2012 | 1996 Plymouth Grand Voyager

2 Answers

My Weed Eater FL25 has rotted fuel lines. One is attached to the primer. Is the other the main? Is there a proper way to replace them? Diagram?


The brass fitting on the carb closest to the primer/purge bulb has a line on it that takes old fuel/air inside the carb and sends it TO the fuel tank. So it is routed straight to the tank. The lower brass fitting on the carb (side with vent hole in cover) has a line that goes directly to the fuel tank and has the in-tank fuel filter on it's end. To insert the main one that gets the filter on its end into the fuel tank, slice a notch out of the end of it so you can squeeze it into the hole in the tank. You can then twist and push it until enough of it goes in to grasp ahold of it with long tweezers or needle-nose pliars. Start off with about 1 foot of Tygon fuel line so you can do this. After you get ahold of it, pull it up thru the fill hole and attatch the filter. Then let it lay it the tank so it will move side to side on the bottom. With the extra line coming out of the tank (it seals the hole) see how much you need to reach the intake fitting on the carb (side with vent hole in cover). Cut it off and attatch it . The other line by the bulb only needs to enter the fuel tank about 1/2 inch or so and it also will seal the hole it goes through. You can notch it as well to help get it started into the fuel tank. This line will be short. I recommend you use NEW Tygon fuel line. I also recommend you get a new primer/purge bulb when you replace the fuel lines. It will deteriorate very soon, ask me how I know! They might have a fuel line kit with the filter, lines and bulb for your machine at Home Depot. Ebay has kits I know. Or you can go to the small engine repair shop and get exactly what you need.

Aug 07, 2011 | Garden

1 Answer

I have a Homelite "Vac Attack" leaf blower model


The fuel line is replaceable by itself, you don't need a new tank. Just make sure you get the same size line or it will leak where it goes into the tank. Any local small engine repair shop should have the line. There are two lines that go into the tank, the pickup line has the filter on it. It not only filters the gas but keeps the end of the line down in the fuel.

Nov 02, 2010 | Homelite Garden

2 Answers

My Rioby trimmer ned fuel hoses change how i do?


Typical fuel line routing is:

One line (the one with the fuel filter in the end of it) comes out of the fuel tank and goes to the bottom fitting on the carburator. The second line comes out of the tank and goes to the bottom fitting on the primer bulb. The third section of line goes from the top fitting on primer bulb to top fitting on the carburator. Hope this helped and best wishes.

Sep 18, 2009 | Garden

1 Answer

Fuel lines inside of tank fell off


This is the typical fuel line routing2.gif on many models: One line ( the one with the fuel filter in the end of it) comes out of the fuel tank2.gif and goes to the lower port on the carburator. The second line goes from the fuel tank to the bottom fitting on the primer bulb. The third section goes from the top port on the primer bulb to the top port on the carburator. Hope this helps and best wishes.

Sep 05, 2009 | Craftsman 25cc Gas Line Trimmer

1 Answer

Fuel lines


The main fuel line goes to the bottom of the tank. The other, sometimes larger line goes to the primer bulb. This line goes just inside the tank, not more than 1"(inch).

May 20, 2009 | Poulan Pro Chain Saw 46cc 20"

2 Answers

Ryobi 700r gas trimmer, replace old fuel lines


Line from tank with the filter on it is the supply line and goes to the carb inlet fitting. This is typically on the "bottom" of the carb (with the tank being up) and will usually have a fitting with barbs or a bulge on it to ensure a tight fit. The other fitting on the carb is the return line and is usually a straight tube fitting with no barbs. That line goes the suction side of the primer bulb. The third line goes from the outlet of the primer bulb to the return barb fitting in the bottom of the tank. Fittings have to be removed from tank to properly install the new hoses on them. Remove retainer ring on outide of tank and push fittings into tank, then shake out of the fill opening. More details on replacing hoses are listed in another post about Repairing Ryobi trimmer.

To leemineres, if hoses are on right and unit still stalls after starting initially you probably need to disassemble carb and clean out using spray carb cleaner. May be sticky needle valve, or partially plugged port or jet.Could also be hole in diaphragm. Gasket and diaphragm kit would be good to add when you take apart, even if diaphragm does not have a hole.

Jan 21, 2009 | Ryobi 30 Cubic Centimeter Curved Shaft Gas...

Not finding what you are looking for?
Craftsman 42cc 18" Gas Chain Saw Logo

169 people viewed this question

Ask a Question

Usually answered in minutes!

Top Craftsman Garden Experts

Wade Mobley
Wade Mobley

Level 3 Expert

475 Answers

Dean Gruber

Level 2 Expert

110 Answers

Roland W VanLue
Roland W VanLue

Level 3 Expert

486 Answers

Are you a Craftsman Garden Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...