Question about Washing Machines

1 Answer

Whirlpool awm 9000 I bought a used Whirlpool

Whirlpool awm 9000 I bought a used Whirlpool AWM9000 but it stops and starts bleeping after about 5 minutes of washing, displaying alternating F and H in the timer screen. What does it mean? What is wrong?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 9 Answers

The error code F/H for this machine means that the drain pump is blocked. Look at your manual for how to access the drain pump and clean it out. This will resolve your issue.

Posted on Oct 19, 2013

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 87 Answers

SOURCE: Whirlpool AWM 8023 -error F06

This erroe code means drive motor tackometer error Probably a bad motor or motor drive pc board or cable problems

Posted on Jun 08, 2007

Coldcut
  • 1554 Answers

SOURCE: Whirlpool AWM 8103/1 error FP

it looks like you have a clog filter or pump issue.
take a look at this forum
http://www.howtomendit.com/answers.php?id=53072

Posted on Feb 25, 2008

  • 41 Answers

SOURCE: Washing machine rubber door seal replacement

Go to www.Searspartsdirect.com You should be able to find an exploded view and parts list

Posted on Feb 29, 2008

  • 1314 Answers

SOURCE: whirlpool washer F22

thats a door lock failure code try unplugging the washer then let me know shut the door firmley before operating

Posted on Mar 28, 2008

richardsimpl
  • 230 Answers

SOURCE: Getting faulf code F06 on Whirlpool 6th Sense AWM 8143

Hi There
I have found what you looking for and i hope this help's yo. let me know.
F/06 Drive Motor Tachometer Error
The control is unable to properly detect motor speed and the machine will shut down. If a failure occurs during high-speed spin, the door will be unlocked after 3 minutes.

  • Check wire harness connections between the Drive Motor/Tachometer and the Motor Control Unit (MCU), and between the MCU and the Central Control Unit (CCU)
  • Check the Drive Motor
  • Check the MCU
  • Check the Wire Harness
Thank you for writing to fix ya.
Best regards Richard

Posted on Dec 12, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I fix a whirlpool washing machine with the 'door locked' light blinking?


The door lock needs to be replaced. I would recommend using a technician to replace the part just to be on he safe side.

Sep 28, 2015 | Whirlpool Washing Machines

1 Answer

Whirlpool ADG 7560 bleeps 4 times


Valued Consumer, We would like to inquire further about your post with you. Please respond back to this email address Whirlpool_Reviews@Whirlpool.com with your name, user id, phone number, street address, zip code, reviewer name, model & serial number, and date of purchase on the appliance.

Apr 15, 2017 | Whirlpool Dishwashers

1 Answer

I require an operation manual for a Whirlpool AWM302


The Whirlpool UK site has support for the AWM 302. The direct link to the manual is http://docs.whirlpool.eu/_doc/501910006566GB.pdf . If this isn't your model, start at http://www.whirlpool.co.uk/support/instructions-for-use/instructions-for-use.content.html and click on Search. Then search using the Commercial code box. (There are also washers with the commercial code AWM 302/3 and AWM 302/4.)

I hope this helps.

Cindy Wells

Jun 03, 2012 | Whirlpool Washing Machines

1 Answer

Hi,does the whirlpool awm 9000 heat water or does it require a constant supply of hot water?


I am not aware of any washers that have built in heaters. Your problem seems to be with your hot water supply in the house. If you have a hot water heater gas or propane pilot may be out, or electric possibly tripped curciut breaker, or if furnace coil , possible furnace servicing is required. Did you just have new machine installed? Did installer forget to turn on the hot water? Basically before you get to upset go backwards from the machine to the problem. It will turn out to be an oversight due to the excitement with your new machine. Enjoy, and GOOD LUCK.

Sep 24, 2011 | Whirlpool AWM9000 Front Load Washer

1 Answer

Can you tell where is the Whirlpool AWM 9000 filter in order to clean it up? Tx


You have to tip the machine backwards and let it lean on wall.# Then you can remove the lower panel on front which is fixed using 3 torx 15 (T15) screws. Take off panel and you can see the filter assembly facing you. Simply unscrew it. Do though take care to clean all calcium off all the seals before putting it back to avoid any leaks.

Sep 04, 2010 | Whirlpool AWM9000 Front Load Washer

1 Answer

I need a rubber ring for the door, where can I get one from in Ireland.? This is a Whirlpool front loading 9kg washing machine. As the machine works very hard and the ring gets pierced a bit too easily I...


Normal 0 false false false MicrosoftInternetExplorer4 /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin:0in; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:10.0pt; font-family:"Times New Roman"; mso-ansi-language:#0400; mso-fareast-language:#0400; mso-bidi-language:#0400;} Sites for spares:
RepairClinic.com (which is good)
espares.co.uk
AppliancePartsPros.com
mcminone.com


Or google whirlpool spares ireland.

Feb 06, 2010 | Whirlpool AWM9000 Front Load Washer

1 Answer

F07-AWM 9000


The F07 indicates a Motor Control Unit (MCU) Error.

  1. Disconnect mains power and unplug unit.
  2. Check wire harness connections between the Drive Motor and the Motor Control Unit (MCU), and between the MCU and the Central Control Unit (CCU)
  3. Check the MCU
  4. Check the Drive Motor
  5. Check the Wire Harness
  6. Reconnect power and plug unit in.
  7. Check the MCU operation by looking for movement of the drive motor, and check drive motor for fully powered rotation.
  8. Replace failed component. Note: If this failure occurs during high-speed spin, the door will be unlocked after three minutes.

Select PAUSE/CANCEL twice to cancel the cycle.
Select DRAIN/SPIN if there is excessive water in the washer.
Re select cycle and select HOLD TO START.

Oct 26, 2009 | Whirlpool AWM9000 Front Load Washer

1 Answer

Whirlpool AWM 045-1000 washing machine has suddenly stopped working and warning light "WATER STOP" has come on. Any ideas for a fix?


Whirlpool AWM 045-1000 washing machine has suddenly stopped working and warning light "WATER STOP" has come on. Any ideas for a fix?

Sep 19, 2009 | Whirlpool Washing Machines

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

73 people viewed this question

Ask a Question

Usually answered in minutes!

Top Washing Machines Experts

Gerry Harvey
Gerry Harvey

Level 3 Expert

1456 Answers

yadayada
yadayada

Level 3 Expert

75066 Answers

Brad Brown

Level 3 Expert

15478 Answers

Are you a Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...