Question about Computers & Internet

Open Question

Oneforall universal remote URC9200 just dies. If i remove and then reinsert the batteries the remote works for a few minutes and the dies again. I have cleaned the battery contacts and also replaced the batteries. There are six jumper pins locates just above the battery compartment, could you pease tall me what they are for. Thanks

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

SOURCE: Toshiba Tecra 8000 doesn't see battery

I've precisly the same problem, but mu battery reaches 15% or so, but then the orange led goes of, and the laptop says there's no battery present. It is probably a problem with your BIOS, and in needs an update, but you'll need a Floppy drive to update the BIOS.
Grtz. Tom

Posted on Jan 19, 2008

  • 3940 Answers

SOURCE: battery not found in power management screen charge light goes out

The Charging circuit on the motherboard is bad, and the motherboard will need to be replaced.

Sorry

Posted on May 18, 2008

rytech uk
  • 85 Answers

SOURCE: jumper location

Im presuming we are talking about the Supervisor Password. (Screen boots to a lock symbol) If so im afraid that there is not a reset jumper as the password is stored on a chip.

To read the chip to get the password would require major 'surgery' on the laptop.

Im not aware of any other soloution to this issue.

Posted on Jun 21, 2008

oldnovii
  • 667 Answers

SOURCE: Directv RC32 remote

Hey DM - Did you remove all 3 screws under the battery cover? The two little black ones near the bottom and the one up inside the battery compartment? Thanks.

Jeff

Posted on Aug 12, 2008

aayushik
  • 59 Answers

SOURCE: How to reset BIOS password - Toshiba Satellite 1605 CDS

you dont have to take the battery off, just unplug the cmos connector which looks like a stereo wiring harness.

Posted on Nov 14, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Need Codes oneforall URC5061


What is the Brand name of your TV?

Oct 03, 2012 | Televison & Video

5 Answers

TV stopped responding to remote control


Unplug Tv from power source, wait 10 minutes and replug

Oct 12, 2008 | Toshiba 42HL67 42 in. LCD Television

2 Answers

Phone just dies for a few minutes every so often--several times a day for the past ten days. Screen goes black and then there's a little white clock icon on the screen. A few minutes later it's fine...


A) Perform a hard reset on the BlackBerry smartphone.
A hard reset involves physically removing the battery from the smartphone and then reinserting it. To perform a hard reset, complete the following steps:
1) Remove the battery cover from the back of the BlackBerry
smartphone.
2) Remove the battery, and then reinsert it after a few seconds.
3) Replace the battery cover.
B) If the display is still not working, verify that the battery is charged by trying it in a different BlackBerry smartphone.

C) If the battery is working, download the latest BlackBerry® Device Software and install it using the application loader tool in BlackBerry® Desktop Manager

Oct 19, 2009 | RIM BlackBerry Pearl Flip 8220 Cellular...

1 Answer

I have the same problem


Hey!

I had this same issue with my Harmony Remote. Logitech sent be these steps and they got it working right!!!

1) Remove the battery from the Harmony Remote for 10 seconds and reinsert it. If this does not resolve the issue, please continue troubleshooting.
2) Ensure you have the latest version of the Harmony Remote Software (7.7).
3) Update the firmware on the Harmony Remote. The following link shows how to complete this task:
http://logitech-en-amr.custhelp.com/cgi-bin/logitech_en_amr.cfg/php/enduser/std_adp.php?p_faqid=10747
4) Try putting the Harmony Remote in safe mode and complete the firmware update again. The following are the steps to accomplish this:
a) Remove the battery from the Harmony Remote.
b) Press and hold the power button while reinserting the battery into the Harmony Remote.
c) To get out of safe mode, remove the battery for 10 seconds and reinsert it into the Harmony Remote.

I hope this gets the display on your Harmony Remote working too!!!

-Kennedy

Sep 22, 2009 | Logitech Harmony One Advanced Universal...

1 Answer

Oneforall URC-3220 universal remote


Try this:

http://www.remotecentral.com/cgi-bin/files/rcfiles.cgi?area=other&db=devices&br=oneforall

Sep 12, 2009 | One For All URC4220 Remote Control

3 Answers

Remote control codes and directions


http://www.oneforall-int.com/?pag=54 this will take you to the one for all website with the codes you need for your model

Oct 28, 2008 | RCA Universal Remote Control

Not finding what you are looking for?
Computers & Internet Logo

Related Topics:

18 people viewed this question

Ask a Question

Usually answered in minutes!

Top Computers & Internet Experts

Doctor PC
Doctor PC

Level 3 Expert

7733 Answers

kakima

Level 3 Expert

102366 Answers

David Payne
David Payne

Level 3 Expert

14161 Answers

Are you a Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...