Question about Roland CUBE Street Amp Combo

Open Question

How can I Fix a Scratchy Speaker ( that crackles ) on a Roland Cube Street Amp?

Posted by Anonymous on

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
rabbitbrains
  • 575 Answers

SOURCE: hello my roland street cube

That is the first thing to check. They are most likely inside the circuit board. Remember to replace them with the same voltage and amperage ratings.

Posted on Apr 30, 2011

Testimonial: "thanks...."

Ad
  • 10 Answers

SOURCE: My Roland Cube 20x Amp

If you take your speaker out you can see if it has blown the internal fuse if not it could be the exernal fuse the power adaptor

Posted on Aug 12, 2011

  • 1212 Answers

SOURCE: roland cube street water damage repair

What part of it got wet will determine the course of action.

If the whole unit were submerged, the unit may prove more time consuming to try to fix than to locate a used one. However, I have salvaged imersed laptops before. the procedure is not much different- make sure the unit is as dry as you can possibly make by blowing a fan on it for an extended period of time.- Days.

Once dried, use some contact cleaner on the jack contacts and interupts, any manual control and any switch.

You can then apply power. If nothing lights up, check and replace fuses as needed. Also check the power supply board for failed caps or rectifiers.

Once the power supply is known to be functional, systematically check the LCD display and the aspects of the amp that it controls. This board will be the most vulnerable and most likely to be the source of most issues you will encountr.

If the display survived intact, and amp does nto work, apply a signal to the inputs and trace the signal through the amp with a set of headphones set up with test prods. The problem will be where the signal stops.

Posted on Apr 27, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My Roland FP8 plays very quietly through its own speakers, through an external amp & speaker and through the earphones. There is a hissing/crackling/static sound too from the speakers. Anyone


A number if things can be wrong with it, from the audil preamp to the the audio amplifier. Even as simple as a bad volume control. Does the actual noise change patterns when you move the volume?

Jan 03, 2015 | Roland Music

2 Answers

Roland street cube won't power on due to battery acid leak


Most likely the acid ate the internal power supply, but if you can dis-assemble it and clean any trace of gunk with a toothbrush and electronic cleaner, including the fuse and it's contacts, maybe you'll get lucky.

Nov 07, 2014 | Roland CUBE Street Amp Combo

1 Answer

Www rolandus com support


Point your web browser at http://www.rolandus.com/

"Register Products" is under "Support."

Aug 15, 2014 | Roland CM30 CUBE Monitor Speaker PA...

1 Answer

My Roland Street cube amplifier has a bad speaker- where can I find a replacement speaker?


Rubber cement is an excellent for minor speaker cone damage but if you feel that a replacement is required, try MCM Electronics online. They carry lots-o-speaker replacements. Be sure to match wattage and impedance (ohms) of the speaker though as these are important spec's.

May 21, 2014 | Roland Cube-st Battery Powered Amp Cube...

1 Answer

My roland cube street starts making this really weird loud noise


Hi, Quick Check. Very often the input socket which is soldered directly to the circuit board, will have a broken solder joint. This is common on a very large amount of equipment. Try waggling the plug about and seeing if the noise comes and goes.
Easy fix, re-solder joint. Permanent fix, connect socket to board with flying leads, or fix socket to board with hot glue or epoxy resin.
All the best, Chris the Fader.

Mar 23, 2013 | Roland CUBE Street Amp Combo

1 Answer

Roland cube street water damage repair


What part of it got wet will determine the course of action.

If the whole unit were submerged, the unit may prove more time consuming to try to fix than to locate a used one. However, I have salvaged imersed laptops before. the procedure is not much different- make sure the unit is as dry as you can possibly make by blowing a fan on it for an extended period of time.- Days.

Once dried, use some contact cleaner on the jack contacts and interupts, any manual control and any switch.

You can then apply power. If nothing lights up, check and replace fuses as needed. Also check the power supply board for failed caps or rectifiers.

Once the power supply is known to be functional, systematically check the LCD display and the aspects of the amp that it controls. This board will be the most vulnerable and most likely to be the source of most issues you will encountr.

If the display survived intact, and amp does nto work, apply a signal to the inputs and trace the signal through the amp with a set of headphones set up with test prods. The problem will be where the signal stops.

Apr 26, 2012 | Roland CUBE Street Amp Combo

1 Answer

Roland Micro Cube Amp fuse blew out. How do you fix it?


have a look here:
http://www.ehow.com/how_8698510_fix-roland-cube.html

although it doesn't mention the fuse you will probably find it. Sometimes there is a fuse access on the outer case.

Jan 11, 2012 | Roland Micro Cube Battery Powered Amp...

2 Answers

Hello my roland street cube won't power on, either with dc or batteries....adapter working .could a fuse be blown inside circuitboard? thanks


That is the first thing to check. They are most likely inside the circuit board. Remember to replace them with the same voltage and amperage ratings.

Feb 13, 2011 | Roland Cube-st Battery Powered Amp Cube...

Not finding what you are looking for?
Roland CUBE Street Amp Combo Logo

Related Topics:

27 people viewed this question

Ask a Question

Usually answered in minutes!

Top Roland Music Experts

Vito Vacirca Jr.

Level 2 Expert

140 Answers

Rabbit Brains
Rabbit Brains

Level 3 Expert

575 Answers

Matthew Spark
Matthew Spark

Level 3 Expert

1066 Answers

Are you a Roland Music Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...