Question about Mitsubishi WD-62525 62" Rear Projection HDTV

2 Answers

Device Menu not working

I have a Mitsubishi 62" LCD projection TV. Just recently the device buttons do not work on the front panel or remote. When I try to look at devices the TV will shut off within 30 seconds. I can watch DirecTV with no problem. when I press the arrow up (device button) on remote the screen goes blue and shuts off. Could this be a remote problem. Also when I try to set up the directv remote to operate TV and hit the TV Input the TV will shut off.

Posted by on

  • Anonymous Nov 26, 2007

    We have the same problem, we turn the tv off at night and the next day it is set to Ant and we can't get a picture. If we press device buttons or menu buttons on the remote the tv shuts off in 30 sec.

  • Anonymous Mar 14, 2014

    The remote control does not work and the menu screen will pop up and stay on for a few minutes and then goes away. After a while it stops doing it but the remote still does not work. We have tried unplugging the TV and hitting system reset. It worked a couple of times but does not work any more. Can you help?

×

Ad

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Thanks a alot this worked for my device buttons not working and the tv shutting off. THANK YOU VERY MUCH!!!

Posted on Mar 02, 2009

Ad
  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Champion:

    An expert who has answered 200 questions.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 206 Answers

Could have a stuck button or a corrupt e-prom, but lets try kicking this set in the head, Now these reset codes are model dependent so this code will not work for every set out there but this reset is for the WD-62525. with the set on and with the original TV remote hit the keys in this sequence, MENU-2-4-7-0 this will bring up a service menu, the cruiser should already be on "Initialize" so simply hit enter. this will reset the TV to factory defaults and may fix your problem

Posted on Apr 02, 2008

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Device button is freezing my t.v.


Try this:
1) turn on the TV
2) from the remote control press MENU 2,4,7,0 then ENTER
3) tv will state on screen that it is INITIALIZING
4) when done press the front reset button.
5) should be good to go!
Let me know if this works

Jun 26, 2010 | Mitsubishi WD-62725 62" Rear Projection...

1 Answer

When I push the device button on the remote, I


I had this same exact problem with my WD-62627. I got mine to work by re-initialing the tv. I could not believe this worked. Try this, 1) turn on the TV
2) press MENU 2,4,7,0 then ENTER
3) the TV should INITIALIZE
4) Press the front reset button on the front of the TV.
5) should work again....if so.....
6) email me at Larry1965@hotmail.com to thank me. :)

Dec 30, 2009 | Mitsubishi WD62628 62" Projection HDTV

1 Answer

Mitsubishi WD-62627 62" DLP TV


Try this:
1) turn on the TV
2) from the remote control press MENU 2,4,7,0 then ENTER
3) tv will state on screen that it is INITIALIZING
4) when done press the front reset button.
5) should be good to go!

Oct 26, 2009 | Mitsubishi WD-62525 62" Rear Projection...

2 Answers

My Mitsubishi WD62627 62 in. HDTV Television is not accepting the HDMI cable. Help!


well first what are you trying to connect the hdmi from do you have it on that input selection is the one it connects to the right one the only thing i could think try and see if what you are trying to hook up will work any other way if it should not see it its only a cable like any other one the only differnce is it will allow full 1080 connection it might be bad or in some cases if your trying to go from the source to the receiver then to the tv and unless you are using hdmi for all then it will not work coponets will not work with transfering the signal

Aug 28, 2009 | Mitsubishi WD62627 62" HDTV

1 Answer

Tv wont respond because device menu is changing through each device


I had a similar problem: my WS-55511 would not respond to the remote and the front control buttons (with the exception of Power) cycled through the Device Menu. I solved this problem by disconnecting the front panel. Here's how to do it: 0. Unplug the TV
1. Remove the speaker grill from the front by pulling forward: there are no screws. 2. Disconnect the two cables that are exposed after the grill is removed. 3. Plug the TV back in, wait for 5 minutes to reset. 4. Try using the remote.  Hope this helps! 

Oct 06, 2008 | Mitsubishi WS-55511 55" Rear Projection...

1 Answer

WS-B55 - Remote doesn't respond, front panel partial response


Genius!! Thanks! I took a dry cotton towl and ran it across the keys on my front panel and whatever was stuck, became unstuck..The internet just saved me $150.

Jun 15, 2008 | Mitsubishi WS-55511 55" Rear Projection...

1 Answer

Mitsubishi WS-48511 Device Screen Will Not Go Away


David,
Let's start with unplugging the set from the wall power for 15 minutes. This will hard reset the micro... While that's unplugged inspect the buttons on the front panel of the Tv to see that none are stuck in a pushed-in condition. Plug the unit back in, power it up and if all works okay you're back in business... If not, let try a keyboard unlock. Press and hold the "menu" button on the front panel for 10 seconds. You won't see any on-screen changes but then try to select an input from the buttons on the front of the Tv.
After you've done these drop me a note and if we haven't solved it will try some other things..
Bill

Dec 02, 2007 | Mitsubishi WS48511 48" Rear Projection...

1 Answer

Menu rotates


Had the same problem with the Mitsubishi ws 48511 model. A solution posted in FixYa worked great and might be worth trying as they have very similar electronics and panels -- did you check to make sure that one of the front panel buttons isn't stuck in the depressed postition? For me, the device menu kept cycling and remote wouldn't work. Sure enough, the button was stuck pushed in. It was hard to even notice, but took little effort to get it free. Good luck.

Nov 13, 2007 | Mitsubishi WS-55711 55" Rear Projection...

Not finding what you are looking for?
Mitsubishi WD-62525 62" Rear Projection HDTV Logo

465 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Televison & Video Experts

matt martin
matt martin

Level 3 Expert

1230 Answers

The Knight
The Knight

Level 3 Expert

75846 Answers

Jaime Hernandez

Level 3 Expert

2336 Answers

Are you a Mitsubishi Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...