Question about Bowflex Selecttech Dumbbells

Open Question

Weights will not stay on - Bowflex Selecttech Dumbbells

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

We have a plating certificate for Iveco for Gross weight 26000 with different weights on each Axle. It has a crane. How do we work out how much load can be on?


it works out as 10 ton , 10 ton and 6 ton on the front axle
there may be variations between state regulations so best talk with the relevant authority
Bill of material that was used by the manufacturer to make the vehicle will have the load ratings for each axle so talk with customer relation s direct by phone to get a copy of that engineering specification

Apr 21, 2016 | Cars & Trucks

1 Answer

The needle and arm just slide all the way to the end of the record. What can I do? Thanks!!


The cause of that is a completely worn out stylus! Or if you have replaced it or it is good, then there is not enough weight on the stylus. You can adjust this by adjusting the weight control on the end of the arm. Try 1.5 to start with, then test a record. If it stays in the groove and doesn't rumble then you are good. If it doesn't stay in the grooves increase the weight by a small amount and test again. Keep repeating this till it stays in the groove and doesn't rumble. If it rumbles decrease the weight.

Mar 10, 2015 | Audio Players & Recorders

1 Answer

I have a Technics sl-b2 with a Shure N97ED cartridge and I CANNOT figure out how to get the tonearm in the right spot? When I get it level or even slightly sloped toward the cartridge it seems to bounce...


To get the stylus to stay in the groove but not have too much weight is a question of trial and error. Having too much weight applied will cause the record to rumble, too little and it will skate across the record.
Start by looking up the typical weight of the cartridge. If you have the box or instructions it will say the typical grams to set it at. Or you can look up the specifications online of the cartridge.
On the end of the tone arm is the weight with numbers on set it to the one specified by the cartridge. Then you test a record - best done with headphones. If the record plays ok without jumping and no rumble then it's good. If it jumps - stop - increase the weight by a slight amount only and try again. Repeat till the problem stops. If it rumbles, then decrease the weight as before slightly and repeat till it stops.

Feb 21, 2015 | Technics Audio Players & Recorders

1 Answer

How do I stop needle skating


There are two reasons this will happen first the stylus is so worn it can't stay in the record groove. The second is there is not enough pressure being applied. Generally each cartridge will have it's own required weight. You can look up the model number of the cartridge to see what this is. To set it right however is sometimes a trial and error procces. At the end of the arm is a weight. You should see some numbers on it. You turn this to the number advised for the cartridge. This might be around 1.5 to 2. Then you try a record. If it stays in the groove and there's no rumble sound then you have right. If it's not staying in the groove increase the weight from say 1.5 to 1.8 and retry. Keep doing this till it stays in the groove. If you get to much rumble decrease the weight - again slowly and test like before.

Oct 07, 2014 | Audio Players & Recorders

1 Answer

The hose head keeps falling away from the unit. It should stay pushed in


Has no hose weight or not heavy enough weight on hose under sink. either buy a weight and install on hose about 18" from the bottom of sink. or you can use a 3 ounce fishing sinker with bread tie and tie it around hose aprroximately 18" from bottom of sink. It needs the weight to keep the faucet head in.

Aug 31, 2011 | Grohe Plumbing

1 Answer

1210 tone arm won't stay down. When I unscrew the


Check the point where the arm piviots, maybe a screw has come loose. Depending on the type of cartridge it should track at 3 to 4 grams.

Jun 08, 2011 | Technics Audio Players & Recorders

1 Answer

Doesn't stay flush to bottom, good suction, if I hold front portion down it works great!


It's most likely a piece of debris in your flapper of your automatic pool cleaner. Debris may prevent flapper movement or restrict flow. You might also want to check for proper hose balance. The hose should stay at a 45 degree angle to the pool floor. If it is greater than a fourty five degree angle, the hose is too light. Move the weights closer to cleaner, or move the first two weights closer to each other. If it is less than a 45 degree angle, move the weights away from cleaner, or separate the first
two weights away from each other.

Feb 12, 2011 | Universal Kreepy Krauly In-Ground Pool...

Not finding what you are looking for?
Bowflex Selecttech Dumbbells Logo

Related Topics:

51 people viewed this question

Ask a Question

Usually answered in minutes!

Top Bowflex Sport & Outdoor - Others Experts

Jerry Greenberg
Jerry Greenberg

Level 3 Expert

1667 Answers

Tom Chichester

Level 3 Expert

35531 Answers

Are you a Bowflex Sport and Outdoor - Other Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...