Question about NEC NP4000 Projector

1 Answer

NEC NP4000 on turning power switch on the power light goes orange for 3 sec then the status and lamps 1 & 2 indicators turn orange at same time for 1 sec and all turn off together, the cycle keeps repeating. Any idea's?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 422 Answers

Sounds like the either the bulb or the fan is a goner.
does the fan spin? if yes, then its the bulb.

Posted on Oct 17, 2013

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

SOURCE: Lamp will not come on

try pressing and holding the enter button on the projector for about 30 seconds - this resets it. It worked for me!!

Posted on Feb 20, 2008

Gigatech
  • 259 Answers

SOURCE: Status light blinking red

If it is a lamp error try this:
When the lamp exceeds 2100 hoursof service, the projector cannot turn on and the manu is not displayed. Do the following:
For VT670/VT470 Press the help button on the remote control for a minimum of ten seconds.

For VT570/VT47 Press and hold the power and the exit buttons on the remote control simultaneously for a minimum of ten seconds. When the lamp time clock is reset to zero, the lamp indicator goes out. Hope this helps! :]

Posted on Feb 27, 2008

  • 1 Answer

SOURCE: Blinking status light

Replacing the lamp with an old one was helpful for me. Good news: the projector itself not faulty. Bad news: I have two projectors with the same issue at the same time (the lamps were replaced also at the same time) after only 400 hours of running.

Posted on Jun 23, 2008

  • 1 Answer

SOURCE: NEC LT30 - Lamp dosen't turn on.

From the manual: To reset the lamp hold down the "HELP" button on the remote for 10 sec and the lamp indicator will turn off. Then start up the projector again.

It worked for me!

Posted on Oct 22, 2008

  • 1 Answer

SOURCE: lamp won't light / status indicator blinking red

Replace the bulb.

Posted on Jun 10, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

The projector turns on but won't project any light through the lens.


If this is a NEC VT series projector, Change the lamp. When if it continues to blink amber and not project and image after installing a new lamp check the lamp cover to see if the micro switch tab on the lamp cover broke off. Some models have a built in lens cover. If the cover is not slid over to open completely the light may not turn on.

May 19, 2014 | NEC VT800 LCD Projector

2 Answers

NEC lt240 lamp light stays off and power light is orange, no Image


COULD HAVE HOUR COUNT LAMP LOCKUP YOU WILL NEED TO RESET HOUR COUNTER BY USING BUTTON CONFIG AND MAINS.

john

www.jvsvisual.com

Apr 15, 2013 | NEC LT 240 Multimedia Projector

1 Answer

Panasonic projection TV does not turn on.


Power LED flashes orange 1 x 5 secs. = 1 of 3 fans stopped. TEMP LED flashes 1 x 5 secs, = Temperature error. Lamp LED flashes 1 x 5 secs. = lamp ballast error. (check lamp 1st.)
Hope this helps.

Apr 18, 2010 | Televison & Video

1 Answer

Status indicator flashes 3 short times, then one long red flash


Once the status light blinks 3 times, this is an indication that there's a problem with the lamp. The lamp may need a replacement.

If you replace the lamp, but get the same problem, check the inverter board.

If you're not sure where the inverter board is, then you may need to contact a pro for your safety.

Good luck and have a good evening!

Feb 14, 2010 | Mitsubishi WD-52327 52" Rear Projection...

2 Answers

NEC VT 595 wont turn on. Just red blinking light


I had this same problem with 2 NEC VT595 projectors. My problem was that there was a broken "tab" on the lamp cover (the plastic cover that slides in place over the lamp) that is supposed to depress a switch which insures the lamp cover is in place before operating the projector. The tab was broken in half and not making the connection there for causing the blinking status light (.5 sec on, 2.5 sec off) indicating a lamp housing or cover error.

May 28, 2009 | NEC VT595 LCD Projector

2 Answers

Blinking status light


Replacing the lamp with an old one was helpful for me. Good news: the projector itself not faulty. Bad news: I have two projectors with the same issue at the same time (the lamps were replaced also at the same time) after only 400 hours of running.

Apr 01, 2008 | NEC VT47 Multimedia Projector

2 Answers

Lamp not lighting


Reset the lamp and try it.

Mar 28, 2008 | NEC VT660 Multimedia Projector

3 Answers

NEC LT30 - Lamp dosen't turn on.


From the manual: To reset the lamp hold down the "HELP" button on the remote for 10 sec and the lamp indicator will turn off. Then start up the projector again.

It worked for me!

Mar 17, 2008 | NEC LT30 Multimedia Projector

2 Answers

Lamp will not come on


try pressing and holding the enter button on the projector for about 30 seconds - this resets it. It worked for me!!

Feb 10, 2008 | NEC VT460 Multimedia Projector

Not finding what you are looking for?
NEC NP4000 Projector Logo

145 people viewed this question

Ask a Question

Usually answered in minutes!

Top NEC Office Equipment & Supplies Experts

jasbo
jasbo

Level 3 Expert

2237 Answers

Electro Med Services...
Electro Med Services...

Level 3 Expert

6694 Answers

The Knight
The Knight

Level 3 Expert

74377 Answers

Are you a NEC Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...