Question about Bosch 1 916 SDS Max Rotary Hammer Drill 11240

1 Answer

Replace grease bosch rotary hammer - Bosch 1 916 SDS Max Rotary Hammer Drill 11240

Posted by Anonymous on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Bosch Master
  • 1,773 Answers

There is no grease but oil used in this tool There is a special consumables kit for to order But BEFORE you made a self service for this machine there could be a rip somewhere in the spindle control first by ringing listen to the sound tap on it it with a piece of metal that the spindle sounds well without also all in and outside parts naturally and off if it does is the sds chisel drill conduction inside the spindle is not round toppen instead of square topped because of faultering on the chisel or drill in short time to expect. in that case if the spindle is bad its better to remplacement the whole tool by Bosch for the working hours on all parts are reached, but if the spindle is smooth order 1 615 437 511 oil reservoir and 1 617 000 A16 thats the right maintenance partsset for this machine and its is easy to service by yourself a little 2 or 3 hours without special tools for special kevlar rings like some other brands often have. but a bank vice and some little screwdrivers noseplier, shaft retaining ring pliers a solvent cleaner for the old lubrication to remove.
AND IMPORTANT dont forget part 104 best to give that o-ring some grease that it will not move out by insert the spindle (sometimes)
one thing is very important there must inside be 2 adjust rings between the gears 47 and 51 if there is only one shimring = used then order some shim rings ( there must be made an adjust between 0,08 and 0,22 mm between the gears tooth but only when there is only 1 ring was used that can be happen in a rare case. the drawing is to find also by bosch in america the partnumbers are the same.
http://www.powertools-aftersalesservice.com/public/boschprof/service?p_auth=ZdEJ7pFj&p_p_auth=R78yYhDo&p_p_id=WSRP_bc93764e__6873__4b00__9a29__b331c9759da9&p_p_lifecycle=1&p_p_state=normal&p_p_mode=view&_WSRP_bc93764e__6873__4b00__9a29__b331c9759da9_wsrp-navigationalState=L0JPUy9QVEFTLVBULVNJUy1TaXRlL25sX05MLy0vRVVSL1ZpZXdQcm9kdWN0LURpc3BhdGNoO3BnaWQ9YmI5NWI3MGRjM2E3NzQxY2ExYzA0OGYyM2IzMDdhNWQ4RkJCO3NpZD1Zdks0RVZOU3dzVm1OZ3M3YnNlazZselpkRGtMODVwSi1QTTd1dEh5ZERrTDg1cEotUE09

Posted on Jan 01, 2017

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

jimboz4
  • 305 Answers

SOURCE: looking to add oil to rotary hammer Bosch / Bulldog

the oil seal is broken, remove front cover at the chuck end of the drill, and replace the seal,

Posted on Jul 22, 2009

Tnsiouxfalls
  • 617 Answers

SOURCE: need \rnBosch Rotary Hammer Manual 11255VSR

http://mdm.boschwebservices.com/MDMCache/English%20[US]/t10/0000001/r01003v-1.pdf
here you go!

Posted on Jan 16, 2010

comax
  • 154 Answers

SOURCE: looking for an owners manual for a 5/8 bosch

If you go to Boschtools.com you will find the manual you are looking for. They are all on the web site.

Posted on Jan 19, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I replace brushes on this drill?


[PDF]Hammers and Hammer Drills - eBuild

www.ebuild.com/ImgRepos%5C2010%20Hammers.pdf_06072010_110..See pages 46-49,. 184-214 for hammer drill accessories. BOSCH. H a m m e rs a n d.... 11250VSRD - 3/4" SDS-plus® Rotary Hammer .... technician can quickly replacethe brushes and cord .... 11264EVS - 1-5/8" SDS-max® Rotary Hammer.

Oct 20, 2015 | Bosch 11264EVS 1-5/8 SDS-Max Rotary Hammer

1 Answer

How much grease goes in a bosch 11335k?


I believe this tool takes 225 ml of grease, but I would strongly recommend installing a service kit #1-617-000-702
The service Kit comes with grease and all the normal wear parts (highlighted below in black circles) Service Pack 1617000702 for Bosch Power Tool eReplacement Parts
24642700-1tmh4chmwaodqgbdv43dd3kn-3-0.gif

Jun 16, 2014 | Bosch 11241EVS SDS-Max Rotary Hammer

1 Answer

Takes a half hour to start rotary hammer function


All grease packed hammers require a certain period of time to warm up. Depending on the room temperature, this time may vary from approximately 15 seconds (90'F) to 2 minutes (32'F). A new hammer requires a break-in period before full performance is realized. This period may require up to 5 hours of operation.
- depending on the time the device has already been in use it is recommended it should be regreased with a special gear lubricant, - perhaps the grease inside has been used up already, then a proper function of the device is not possible anymore and it has to be serviced.

takes-half-hour-start-rotary-hammer-l2syhiveb5h5n2hnqsepdito-5-0.jpg

takes-half-hour-start-rotary-hammer-l2syhiveb5h5n2hnqsepdito-5-6.jpg

takes-half-hour-start-rotary-hammer-l2syhiveb5h5n2hnqsepdito-5-9.jpg

Dec 18, 2013 | Bosch 11236VS Rotary Hammer

1 Answer

What type of oil for bosch 11224vsr rotary hammer drill


special grease is used not oil order number 1 615 430 001 is the right grease for it

Apr 08, 2013 | Bosch SDS-plus BULLDOG Xtreme Rotary...

1 Answer

What position should striker be in a Bosch 11203


It works on a pnumatic system, Light oil or grease is fine on the piston its self but grease in the gearbox. (don't over do it) Have the piston partially sticking out. Make sure you locate it onto the ecentric cam correctly. If it does not hammer at first just run it for a while against the work, stopping and starting it in short bursts.

Jun 06, 2012 | Drills

1 Answer

I have a bosch 11240 and the tool holder will not hold the tool, is there an easy fix


"CHUCK" is full of dust, clean with a good cleaner lubricant, white grease before using again

Oct 19, 2010 | Bosch 11240 1-9/16" SDS Max Combination...

1 Answer

Looking for lubrication info on Bosch rotary and demolition hammers. I am doing a service pack and need to know proper lubrication points and amounts to refresh my drills for work. Any place to find repair...


try going to Boschtools.com and you will need your exact model number but they have parts explosions with the grease points listed on most of them Let me know if you need more assistance.

Mar 06, 2010 | Rotary Bosch 11263evs 1-3/4'' Sds-max® ...

2 Answers

Hammer action power there but weak


It is hard to understand what you are asking, however I have found that with the SDS drills one does NOT want to crowd them but just let the tool work with light pressure...

Feb 07, 2010 | Bosch SDS-plus BULLDOG Xtreme Rotary...

2 Answers

I have a bosch rotary hammer 11245evs and it was working when i put it away in its case, now it will not hammer. Drills ok. larry


They are filled with a special grease that comes from Bosch. It sounds like the impact bolt or the striker pin in the unit are not moving the way they should. These are the pieces that work together to create the hitting action. About all that can be done now is the unit has to be dismantled to get those to pieces moving again. Bosch makes what they call service packs for all thier hammers. They have all the o-rings and grease to get your hammer working again. A Bosch service center can supply you with the kit. Ask for P/N 1617000225, or they can take care of it for you.
Hope this helps

Apr 16, 2009 | Bosch 11241EVS SDS-Max Rotary Hammer

1 Answer

BOSCH 11236VS HELP ME WITH A PROBLEM


I order parts for my Bosch tools at WWW.toolpartsdirect.com. They have the parts lists also so it is easy to find what you need. Don't forget to order some bosch grease for your tool because you will need to carefully wash-out all the old grease with metal bits. Good luck with you repair. Enjoy

Nov 25, 2008 | Bosch 11236VS Rotary Hammer

Not finding what you are looking for?
Bosch 1 916 SDS Max Rotary Hammer Drill 11240 Logo

Related Topics:

1,025 people viewed this question

Ask a Question

Usually answered in minutes!

Top Bosch Hammering Experts

John Trevino

Level 3 Expert

1383 Answers

Doctor PC
Doctor PC

Level 3 Expert

7733 Answers

snowycreek

Level 2 Expert

36 Answers

Are you a Bosch Hammering Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...