Question about Tools & Hardware - Others

Open Question

Surebonder staple gun wont staple - Tools & Hardware - Others

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 2712 Answers

SOURCE: Staple Gun Troubleshooting

Most of the staple gun models lack an "anvil" — the metal plate with curved slots that office staplers use to bend the legs of the staple inwards and flattens them against the paper. Staples set with a staple gun retain their straight legs, and are held in place only by static friction of the legs against the compressed surrounding material, much like common nails. Indeed, some staple gun models can handle brads and nails as well as staples. Some staple guns also use divergent point staples where the legs twist as the staple drives into the surface providing superior holding power.

Posted on Aug 27, 2008

Ad
  • 2712 Answers

SOURCE: staple gun support

Know the types of staple guns available. They can be manual, electric, battery operated or run by compressed air with an air compressor. Some staple guns have guide wires because they’re used by electricians that can’t pierce wires. Others have long noses to work well in corners and tight spaces. There’s also a reverse built ergonomic staple gun called a "forward action" because the handle and the staple’s exit point are on the same end of the staple gun. Some staple guns can shoot brads instead of staples. Know how each type of staple gun works. This one is so simple because it works just like a stapler. You press and hold the silver latch on the back of the stapler to open the body. Take the tray out and fill it with staples. Then it’s ready to use. Just put the staple ejecting end on your piece to be stapled and squeeze it. There is also the forward action manual gun which is used by pushing the handle down, too. The handle is just located near the staple ejection site. Use an electric staple gun for effortless stapling. There’s no need to squeeze or apply any pressure on these guns. They come with a very short cord so you will always need to have an extension cord with your staple gun. You can also go with a rechargeable battery operated cordless staple gun. They are great but they do run out of steam so for long use one with a cord is better. They’re also pretty easy on the wallet these days, so there’s no reason to go without this in your home tool kit as it’s something that does a lot of jobs. Know the versatility of the staple gun. Whether you have a manual or an electric model, these are some of the most versatile tools out there. You can use them to recover furniture, to build a birdhouse, to staple lattice to a patio, to build lightweight projects like a small knick knack shelf and to do wiring work.

Posted on Aug 27, 2008

  • 1 Answer

SOURCE: staple gun

Open the chamber and drop the staples upright in to the chamber do not try to load the staples by placing them on the strip that pulls out as you do with most staple guns.

Posted on Nov 25, 2008

danny_murray
  • 55 Answers

SOURCE: Need help on how to put staples in Ace staple gun 22084

At the very botton of the stapeler in the back there should be a square mechanism press in and down then just slide the staples in and eplace the mechanism the way you took it out

Posted on Dec 05, 2008

joboo1
  • 257 Answers

SOURCE: Haubold 1400 series Staple Gun has blown an ''o'' ring.

Hi, I repair lots of tools and ended up buying a complete like 2000 part o ring kit I keep in my shop, it has proven invaluable, If you can't find the o ring at a hardware store, give ample supply a call and see if they can help you, their number is 1-800-339-5667.

Thanks for using FixYa - a FixYa rating is appreciated for answering your FREE question.

Posted on Mar 27, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where can i get a assembly diagram for a surebonder 5900n


There is no assembly diagram available for the Surebonder 5900N.

Sep 25, 2016 | Surebonder 5900 Electric Staple Gun

1 Answer

How do you load staples into a surebonder model 9630?


Loading a 995630. Hold gun upside down with front of gun in left hand. Open track release with right hand. Lay one section of 1/4" crown staples in the bottom of the gun itself, in front of the track. Slide track over staples. Store tool at room temperature. New gun needs 6 drops of air tool oil through the air inlet just before first use. If you do not have the recommended automatic oiler installed on your airline, you will need to manually oil with three drops every 3rd row of staples. Run PSI around 80 and never exceed 100 PSI on your air compressor.

Sep 01, 2014 | Surebonder Pneumatic Stapler

2 Answers

What Staples does a swingline 34301 Electric Staple Gun take?


That's an easy one
Use the Arrow 600 series staples. heres the link to the different sizes available.
http://www.arrowfastener.com/catalog/supplies/staples/600-series


Good luck and don't forget to rate me :)

Aug 09, 2014 | Staples Swingline® 36115 Staple Guns Tools...

1 Answer

Model 5580


Couldn't find a picture, but I found this:

"I was stumped as to how to put the staples in at first then I looked at the writing on the bottom and then it was easy."

Dec 22, 2013 | Surebonder Tools & Hardware - Others

1 Answer

Surebonder 9600


Call the manufacturer with your email address and ask for detailed instructions on how to replace the pusher and spring on your specific model number.
These are instructions on replacing the spring and pusher for Pneumatic model #'s: 9600, 9610, 9615.

1. Wearing protective eyewear, remove air line supply HOSE from your gun, turn gun upside down holding the front of the gun in your left hand

2. Remove u-shaped piece that holds the track in place at the back of the bottom of the gun.

3. Slide track out of gun.

4. Take the long black spring (part # 38) and hook one side of it to the hook inside the pulled out track.

5. Feed the other side of the spring under the silver wheel in the front of the track and pull it up holding the tension. You might need to use the end of a paperclip to feed the spring through.

6. Take the u-shaped pusher (part # 33) and place the other end of the springs hoop onto the hook inside part #33. Make sure the opening of the hook faces the back of the track, and that you see the yellow tape so that it will show in your view window.

7. Carefully place part #33 with the spring attached and the opening of the hook facing the back of the track, back onto the front of the track. The springs tension will hold it in place.

8. Carefully slide the track back into the bottom of the gun making sure you are placing each side of the track into the grooves.

9. Carefully snap the u-shaped lock back onto the bottom of the track to hold the track in place.

10. With the tool upside down, slide your track open and be sure to place your staples in the bottom of the gun itself with the points of the staples pointing up towards the ceiling, not on the track.
Parts are available online at www.surebonder.com on the left hand column, select Pneumatic Parts, then select your tool. It will bring you to the ordering page.

Mar 17, 2013 | Surebonder Pneumatic Stapler

2 Answers

Do I adjust the staple depth with the pressure from the regulator?


there should be a thumb screw behind the trigger. turn it clockwise for a deeper depth and counter clockwise for shallower.
Let me know if this helps

Feb 26, 2011 | Surebonder 9600 Pneumatic Fine Wire Staple...

1 Answer

Remove a jam staple from a hardwood floor stapler


on that model there should be a few bolts on the tip side of the nose , remove screws and top part of nose and remove the damaged staple,, then replace parts

Nov 30, 2009 | Surebonder Pneumatic Stapler

1 Answer

Surebonder 4.8 v cordless stapler


with mine there is a fine spring on the plunger which holds the staples in which i restretch every now and then you could also try checking for jammed staples and putting one or two drops of oil on the shaft that pushes the staples down after the oil operate afew times empty of staples see if this helps bestaluck glenn

Oct 26, 2008 | Tools & Hardware - Others

Not finding what you are looking for?
Tools & Hardware - Others Logo

Related Topics:

25 people viewed this question

Ask a Question

Usually answered in minutes!

Top Tools & Hardware - Others Experts

Doctor PC
Doctor PC

Level 3 Expert

7733 Answers

Brad Brown

Level 3 Expert

15633 Answers

J.D. Browning
J.D. Browning

Level 3 Expert

2760 Answers

Are you a Tool and Hardware - Other Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...