Question about Craftsman 10" Table Saw

1 Answer

Elevator won't. Model 113.231 RAS. How do I go about disassembling it.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Craftsman Master
  • 15,557 Answers

You are saying that you can raise or lower the blade?

Posted on Oct 14, 2013

Testimonial: "Elevator will neither elevate or lower. Seems I need to take it apart and see what's up,although the initial inspection failed to show any type of buildup or other obstruction. BTW thanks for your time!!"

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Error 9E 09


Error 9E 09

9E : Elevator range out of specification

Primary: Library Enclosure
Secondary: Library Controller Card
09 : Error elevator init

Nov 02, 2012 | IBM System Storage TS3200 Tape Library...

1 Answer

Hitachi RAS-09UH Air Conditioner won't turn on


If you can access the pcb inside, check the mini glass fuse

May 18, 2012 | Hitachi RAS-09UH Air Conditioner

1 Answer

We have a Hitachi Model RAS-63CHA2 that we need to find out how old the unit is as it has broken down. Can anyone tell me when these models were first produced?


This model was produced approx 6-8 years ago a common problem is the compressor capacitor 50uf. I must of changed 50 of them by now.

Jan 19, 2011 | Hitachi RAS-09UH Air Conditioner

1 Answer

Error 720 - the connection attempt failed because your computer and the remote computer could not agree on PPP control protocol. Gateway Desktop


To resolve this behavior, follow these steps:
  1. Find out which protocols the RAS server is running, and make sure that the RAS service is installed and configured properly (or ask the Network Administrator to do this).
  2. After you find out which protocols the RAS server is running, make sure that your Windows XP-based computer is running one of the same protocols that the RAS server is running:
    1. Click Start, click Control Panel, and then double-click Network Connections.
    2. Under Virtual Private Network, right-click the VPN connection, and then click Properties.
    3. In the VPN Connection Properties dialog box, click the Networking tab, and make sure that you have a protocol that the RAS server is running.
  3. If you do not have a protocol that the RAS server is running, add the needed protocol:
    1. Click Install, click Protocol, and then click Add.
    2. Click the protocol that you need to install, and then click OK.
    3. Click Close in the VPN Connection Properties dialog box.

May 30, 2010 | Acer Aspire T650 PC Desktop

1 Answer

Manual for a Toshiba Heatpump model RAS-16 NKV-A2


You can download your manual from this Toshiba Website. It's approximately halfway down the page. :-)

Mar 28, 2010 | Heating & Cooling

2 Answers

Bizhub 350 erro code c1183


C1183
Elevator motor ascent/
descent drive failure
• The elevator tray lower limit sensor (PC13) is not turned ON
even after the set period of time has elapsed after the main
power switch is set to ON.
• The elevator tray home position sensor (PC11) and elevator
top face detection sensor (PC12) are not turned ON even
after the set period of time has elapsed after the elevator
motor (M11) is energized.
• The elevator tray does not stop at the position for the specified
tray after the elevator motor (M11) is energized (beginning of
descent operation) and the elevator tray lower limit sensor
(PC13) is turned ON.
• The elevator top face detection sensor (PC12) is not turned
ON even after the set period of time has elapsed after the elevator
motor (M11) is energized (beginning of ascent operation)
when paper is being fed out.

May 06, 2009 | Konica Minolta bizhub 350 All-In-One Laser...

Not finding what you are looking for?
Craftsman 10" Table Saw Logo

Related Topics:

86 people viewed this question

Ask a Question

Usually answered in minutes!

Top Craftsman Saws Experts

Doctor PC
Doctor PC

Level 3 Expert

7733 Answers

Mike

Level 3 Expert

4336 Answers

Are you a Craftsman Saw Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...