Question about Dream Maker Spas Dream Maker SpaDition Vico Pump 15 HP ()

1 Answer

My ezspa is set for 102. Every time the temperature reaches 97 degrees I get a 104 degree light on and continues to flash when the water temp is really 97. I reset it continuously. When it flashes 104 I loose all control of the control panel. Unable to turn it off or turn the light on or off.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 3,103 Answers

Thermostat is going out.. needs replaced.

Posted on Jan 11, 2014

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Just installed new rs8pcb and temp sensor. Set at 104,only reaches 102, why?


Try calibrating your Jandy controller to the temperature of the heater. Temp sensor could be off by two degrees

Dec 04, 2016 | Pool & Spa

2 Answers

My spa temperature light is blinking. It is set at 104 and the temperature is showing 118. Why is the temp blinking?


If you can contact your spa manufacturer they will usually send you the manual for your unit at no cost.
If the temperature is set at 104 it is at the high end of the safe temperature for a human. 102 is recommended, and 103 is OK for 15 to 20 minutes maximum.
If your spa is actually at 118 degrees, it could easily cause very severe medical heat distress. I would strongly recommend NOT using it until you can get the temperature down.
It's possible that the blinking light is a warning.

Jun 14, 2015 | Intex Pool & Spa

1 Answer

The OH Light keeps coming on although the temperature never exceeded 100 degrees.


check your recirculation pump it sounds like it isnt working or plugged filters

Oct 16, 2014 | Pool & Spa

1 Answer

Hs error code what does it mean?


Water Temperature Sensing Error

A) Inlet water temperature sensor is reporting a temperature in excess of 104 degrees. Normal operation resumes 2 minutes after inlet water temperature sensor reports temperatures of 104 degrees or less. This error functions in both normal and remote thermostat modes.
or

B) Inlet water temperature sensor is reporting a temperature change at a rate faster than 6 degrees in 60 seconds, indicating a potentially damaging low water flow condition. Normal operation resumes when temperatures stabilize. If this condition is detected 3 times, the heater will lock-out until the electrical power is cycled off and back on.

Jun 19, 2014 | Hayward H400FDN Low NOx Natural Gas Pool...

1 Answer

South seas spas


need more info. will temp lower? if temp lowers try setting up to 104 if desired temp will not increase sounds like you need temp adjustment switch if desired temp goes up to 104 but water doesnt
sounds like temp sensor if temp sensor is good heater element

Feb 16, 2014 | Pool & Spa

1 Answer

My indoor RS4 panel says the spa is heating, and then reached 101 degrees. But when we got in, it was only 97 degrees and the outdoor panel displayed 97 degrees. Everything else seemed to be working fine.


If the heater is set to 104 then this is probally your Aqualink temp sensor. This is mounted in a pipe with a stanless steel clamp holding it in place. If you follow the wire back to the controler box it just unplugs and the new one goes right back in. Easy to do and the part is inexpensive.

Sep 26, 2009 | Jandy Aqualink Rs4 One Touch Control...

1 Answer

When I change the temp. setting it keeps heating at original temp


The keypad appears to working correctly.

When you alter the set temperature via the keypad the display will flash the temperature thats to be acheived, once it stops flashing the keypad will revert back to the current temperature of the water.

Hope that helps,
Ian.
http://hottub.synthasite.com

May 24, 2009 | Balboa Instruments Duplex Digital Panel 2...

Not finding what you are looking for?
Dream Maker Spas Dream Maker SpaDition Vico Pump 15 HP () Logo

90 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dream Maker Spas Pool & Spa Experts

Ian Kime
Ian Kime

Level 2 Expert

77 Answers

john h

Level 3 Expert

12104 Answers

The Cover Guy
The Cover Guy

Level 2 Expert

64 Answers

Are you a Dream Maker Spas Pool and Spa Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...