Question about Office Equipment & Supplies

Open Question

I was informed of a firmware update for the Epson XP-310 printer. I started the process and got to the point where I had to enter the email confirmation address used for registration. I had to go through Google to register, but when I tried to finish the firmware uprgrade, the screen erased the window that I had to enter the email into. Was the upgrade successful? Thank you in advance.

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
bluegreenash
  • 661 Answers

SOURCE: Firmware Upgrade Problem

the code 37,024.42 suggests a hardware failure

according to the error code manual

https://www.office.xerox.com/partners/products/Phaser8500/SQRG/03_error_codes.pdf

Drum heater relay board disconnect.
Both drum heater relay coils are not drawing the expected power from the supply.

I hope this helps

Posted on Sep 27, 2008

Ad
  • 1 Answer

SOURCE: Reverse Firmware Upgrade

http://www.fixyourownprinter.com/forums/printer/56368
----------


There are two different print engines used in the CLP-300. One for 2006, and a different one starting in 2007. I have the older 2006 printer, and the current firmware is only for the new 2007+ print engine.

I talked to Samsung support here in Korea and fixed the problem. They sent me to their special tech support website at www.1479.co.kr (only in Korean) and I was able to download an older version of the firmware which restored my printing ability.

The latest version of firmware that worked with my printer was found in this post: http://www.bassmania.co.kr

Download the two files at the top, then extract the archive. Drag-n-drop the correct firmware file onto "usblist2.exe" and the printer will be flashed with the firmware (must be connected via USB if you're using the CLP-300N model).

Posted on Jun 14, 2009

  • 1 Answer

SOURCE: Dell 946 AIO printer won't stop beeping after firmware update attempt

Same thing happened to me....yesterday I went online at www.dell.com to download the latest firmware & driver for my Dell 946 Printer. After downloading the firmware the printer went haywire and is rendered useless. It emits beeps and the green power light will stay lit then flash every 3 seconds or so. There is no read-out on the lcd display.
I phoned Dell only to be told I should not have downloaded the firmware and that Dell does not recommend downloading firmware. If that is the case then why is the firmware listed on the Dell site with instructions to do so? I was advised that no support could be offered because the printer is out of warranty and was told to uninstall the printer and re-install. I have tried everything, including uninstalling printer, unplugging printer, etc. and nothing has helped. I have researched online and note that this is a recurrent problem. This problem is noted in the forums section of Dell.com - I have followed directions listed in the forum section of Dell.com as noted (see below websites) but this has not fixed the problem....

http://en.community.dell.com/forums/p/19261215/19444405.aspx?c=us&l=en&cs=RC1009777&s=fed

http://en.community.dell.com/forums/t/19167220.aspx?c=us&l=en&cs=RC1009777&s=fed

http://en.community.dell.com/forums/p/19256007/19422649.aspx

http://www.fixya.com/support/t416532-dell_946_aio_printer_stop_beeping_after

http://help.com/post/233917-dell-aio-946-printer-help

Since this seems to be a known problem and the problem is actually caused by downloading firmware from the Dell site I feel it is an injustice not to offer some type of support to rectify the problem. I have always bought Dell products and advised others to do so, but with this problem I feel that I will be changing my brand that I purchase.

I will be contacting Consumer Reports - I feel this warrants some type of recall!!

Posted on Jun 29, 2009

  • 183 Answers

SOURCE: Error code 2,155,0

It seems that the printer has communication problem with the computer. If you are sure your USB cable is good than it might be the board of the printer is faulty

Posted on Jan 03, 2010

Testimonial: "Thank you for your assistance. I replaced the 3M cable that is used with the desk top with a 1.8M one. It seems the laptop can't handle the long cable"

  • 1 Answer

SOURCE: Lexmark registration reminder pops up everytime i

64-bit.exe is only for 64-bit vista, not 32-bit, so it will not work! you have to track the registry reminder portion of that lexmark you have down. regedit its registry entry so it cannot autostart. will be looking for details.

Posted on May 23, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My Epson all in one xp-310 will not print using wifi on windows 10


Try the link below. May be helpful
https://epson.com/faq/SPT_C11CC88201~faq-289594

Dec 24, 2016 | Epson XP 310 Wireless Printer Scanner

1 Answer

My Epson xp 310 won't print on cardstock; paper just glides through blank


to be able to print with a ink jet printer, the surface of everything is supposed to be prepared for the ink. When the printer prints fin on "normal" paper, it can print all all surfaces you can fine in your printer settings.

Feb 19, 2015 | Epson Expression Home XP-310 Small-in-One...

1 Answer

Why does the power light just flash on my epson xp 310?


In the manual, you can download on this link, solving problems start on page 175. There are more than 20 pages with problems, Perhaps you can find on one of the pages what is wrong. Epson Expression Home XP 310 Small in One All in One Printer

Jun 27, 2014 | Epson Expression Home XP-310 All-in-One...

1 Answer

SP35 cards not printing more than one colour


Check to see if you have the current firmware installed on the printer. You can discover the version by going to Start > All Programs > Datacard Card Printers > Datacard Printer. Look at the bottom of the of the dialog box [Printer Toolbox] for the number following Printer Firmware Version. The number should be above version 24.49.

Datacard released a a new ribbon model that includes a new RFID chip. Printers with the older firmware will not recognize the new chip and thus think the ribbon is black only.

  1. Update the firmware by going to the Datacard website and use the search function in the top right corner of the website.
  2. Enter the search string "SP35 Firmware" one of the top links will point you the the Driver and Support page.
  3. Once the page loads, scroll down to the firmware subsection.
  4. Click on the "Begin your Go Green firmware upgrade now" link.
  5. Enter the contact info and click submit.
  6. Click download link once page loads.
  7. Open or Run download.
    1. This program will install software on the computer to update printer to new version of firmware. After the firmware is updated the program will ask if you would like to uninstall at end.
  8. A new dialog window will display Card printer Firmware Update.
  9. Select from drop down the Datacard printer that requires a firmware update.
  10. The dialog box will either display the update firmware version that can be flashed or indicate the "printer contains the latest firmware."
  11. If a update is possible click the Update button in the bottom left corner of the dialog window.
    1. Do Not Disconnect the power during the flash process.
    2. The printer will make beeps while the printer is flashing, this is normal.
  12. Wait till you hear the printer perform it's start-up sequence and you see a dialog on screen for success.
  13. Open Printer toolbox as mentioned above and review the firmware version number in the bottom left corner. Notice it should be a number greater than 24.49.
  14. Click on the Supplies tab in the printer toolbox dialog window and review the ribbon type.

Apr 10, 2014 | Datacard SP35 Printer

1 Answer

La impresora 4345mfp se bloquea y nose como hacer la actualizacion del firdware.


Upgrading the firmware
The MFP has remote firmware update (RFU) capability. Use the information in this section to
upgrade the MFP firmware. The overall process involves the following steps:
1 Determine the current level of firmware that is installed on the MFP.
2 Go to the HP Web site and find out whether a firmware update is available. If an update is
available, download the latest firmware to your computer.
3 Transfer the new firmware from your computer to the MFP.
Determining the current level of firmware
To determine the current level of firmware, view the configuration information on the MFP control panel. To view the configuration information, follow these instructions.
1 Press MENU.
2 Touch INFORMATION.
3 Touch PRINT CONFIGURATION. The configuration page prints.
4 The firmware datecode is listed in the section called Device Information. The firmware
datecode has this format: YYYYMMDD XX.XXX.X. The first string of numbers is the date, where
YYYY represents the year, MM represents the month, and DD represents the date. For example, a firmware datecode of that begins with 20040225 represents February 25, 2004.
Downloading the new firmware from the HP Web site
To find the most recent firmware upgrade for the MFP, go to www.hp.com/go/lj4345mfp_software.
This page provides instructions for downloading the new firmware version.
Transferring the new firmware to the MFP
Use one of the following methods to update the firmware.
Using FTP to upgrade the firmware on a network connection
NOTE The MFP can receive an .RFU file update as long as it is in a "ready" state.
The elapsed time for an update depends on the I/O transfer time, as well as the time that it takes for the MFP to reinitialize. The I/O transfer time depends on a number of things, including the speed of the host computer that is sending the update. If the remote firmware update process is interrupted before the firmware is downloaded (while Receiving Upgrade appears on the control-panel display), the firmware file must be sent again. If power is lost during the flash DIMM update (while the Performing Upgrade message appears on the control-panel display), the update is interrupted and the message Resend Upgrade appears (in English only) on the control-panel display. In this case, you must send the upgrade by using the parallel port. Finally, any jobs that are ahead of the RFU job in the queue are completed before the update is processed.
Follow these instructions to perform the upgrade by using FTP.
To upgrade the firmware on a network connection by using FTP
1 Take note of the IP address on the HP Jetdirect page. The HP Jetdirect page is the second page that prints when you print the configuration page.
NOTE Before upgrading the firmware, make sure that the MFP is not in Sleep mode.
Also make sure that any error messages are cleared from the control-panel display.
2 Open an MS-DOS command prompt on your computer.
3 Type: ftp <TCP/IP ADDRESS>. For example, if the TCP/IP address is 192.168.0.90, type ftp
192.168.0.90.
4 Press Enter on the keyboard.
5 When prompted for the user name, press Enter.
6 When prompted for the password, press Enter.
7 Type bin at the command prompt.
8 Press Enter. The message 200 Types set to I, Using binary mode to transfer files appears in
the command window.
9 Type put <filename> where <filename> is the name of the .RFU file that was downloaded
from the Web, including the path. For example, type put C:\LJ\4345FW.RFU, and then press
Enter.
NOTE If the file name or path includes a space, you must enclose the file name or path
in quotation marks. For example, type put "C:\MY DOCUMENTS\LJ\4345FW.RFU"
The following series of messages appears in the command window:
? 200 PORT command successful
? 150 Opening BINARY mode data connection
? 226 Ready
? 226 Processing Job
? 226 Transfer complete
Then, a message that contains the transfer-speed information appears.
10 The download process begins and the firmware is updated on the MFP. This can take
approximately five minutes. Let the process finish without further interaction with the MFP or
computer.
NOTE The MFP automatically turns off and then on again after processing the upgrade.
11 At the command prompt, type: bye to exit the ftp command.
12 At the command prompt, type: exit to return to the Windows interface.

Using MS-DOS commands to upgrade the firmware
To update the firmware by using a network connection, follow these instructions.
1 From a command prompt or in an MS-DOS window, type the following: copy /B <FILENAME>
\\<COMPUTERNAME>\<SHARENAME>, where <FILENAME> is the name of the .RFU file
(including the path), <COMPUTERNAME> is the name of the computer from which the MFP is
being shared, and <SHARENAME> is the MFP share name. For example: C:\>copy /b C:
\9200fW.RFU \\YOUR_SERVER\YOUR_COMPUTER.
NOTE If the file name or path includes a space, you must enclose the file name or path
in quotation marks. For example, type: C:\>copy /b "C:\MY DOCUMENTS\3500FW.RFU" \\YOUR_SERVER\YOUR_COMPUTER.
2 Press Enter on the keyboard. The control panel shows a message that indicates the progress of the firmware upgrade. At the end of the upgrade process, the control panel shows the Ready
message . The message 1 file(s) copied appears on the computer screen.

Jul 15, 2011 | HP LaserJet 4345mfp Printer

1 Answer

I lost my disc


Hi,you can download drivers from the link below..

opendrivers.com/driver/299646/epson-workforce-310-all-in-one-printer-driver-v6.61-windows-xp-vista-windows-7%28all-x64%29-free-download.html


andhttp://www.downloadatoz.com/driver/download/2316,epson-workforce-310-all-in-one-printer-driver.html


Hope it helps.

Thanks for using fixya...

Dec 06, 2010 | Epson WorkForce 310 All-In-One InkJet...

1 Answer

Hp clj cm1312 mfp firmware corrupt ready 2 download, What to me to do? Help, please


You will need to apply the firmware to the machine. I've attached the link to hp site for you to download the firmware file as well. Below the link is the directions on how to accomplish this, as well you can see the same directions on via the link provided

http://h20000.www2.hp.com/bizsupport/TechSupport/SoftwareDescription.jsp?lang=en&cc=us&prodTypeId=18972&prodSeriesId=3558902&prodNameId=3558903&swEnvOID=228&swLang=8&mode=2&taskId=135&swItem=t2-85206-1

Firmware Update Notes:
  1. The Firmware Update Utility uses the USB connection to the printer.
  2. The HP Color LaserJet CM1312 MFP print driver software must be installed prior to using this utility.
  3. The HP Color LaserJet CM1312 MFP printer must be on and in a READY state as shown by the LCD display on the control panel and remain powered on during the entire firmware update process.
  4. Depending on the processor speed of your PC, the firmware update process may complete on the printer before the update status progress bar in the flash firmware update utility on the PC screen completes, this is normal.
  5. Once the update process has started, do not use your PC for any other activity until the process is complete.
  6. Do not power cycle the product or the PC until the firmware update process is complete.
Process:
  1. Download the flash firmware updater file from HP.com to the PC desktop.
  2. Turn the printer off and then back on to clear main printer memory.
  3. Double click on the file CM1312_MFP_Series_FW_Update-20100616.exe flash firmware update utility file. An HP firmware update window will open.
  4. Select the appropriate CM1312 MFP driver in the dialog window. If you assigned a different name to the HP CM1312 MFP, choose the name that represents the correct printer.
  5. Click on "Send Firmware" when ready to proceed.
  6. The progress bar will begin to move to the right indicating information being transferred.
  7. DO NOT power cycle the product or the PC during this process or the product may become unstable and or unusable without further attention from HP. The flash firmware update can take up to 5 minutes to complete. Please be patient.
  8. During the product flash firmware update, the display on the product control panel will display "Printing Document - Erasing - Programming - Complete - Hewlett-Packard - Ready - Initializing - Ready". Once the download is finished the printer will be in the Ready state.
  9. At the conclusion of the firmware update, the dialog window will show a smiley face. Click on exit.
  10. If it is desired to verify the update, use the control panel reports menu under setup to print a configuration report. The configuration report will show the current firmware revision in the Product information block, Firmware Datecode: 20100616

Oct 20, 2010 | HP LaserJet CM1312 All-In-One Printer

1 Answer

My colour printouts from new Samsung CLP-310 do not match original WORD 2000 docs colours (or compared to HP deskjet. Is there a MS patch for this?


Hello,

There is an update for your printer. This is a firmware update. A firmware update, rewrites code located on the printer's main system board. The latest update is dated 10/17/08.

Flashing firmware does not have a go back element or undo, so it is really important that we verify your model and what seiries of printer you have. I suspect you have a CLP-300 Series printer and that the 310 of the 300 just describes some features added or left off and even who you purchased it from, in many cases.

Please look at these two photos and then post the data off the name plate for your model number in particular.

406eb47.jpg ccb435d.jpg

You will notice there are two lines to include in your reply.
1.) The Model: (first line)
2.) M/C entry (second to last entry in this photo of the label.

Once you verify this and I post the firmware update link for you, you will need to follow the instructions I include below.

Regards,
Worldvet


[from Samsung.com PDF file on this firmware upgrade]

Samsung has released a new Software upgrade file for print quality, automatic error recovery, and toner save mode on color laser printers.

Procedure to Set-up Download Mode on Your Printer - CLP-300 series
Turn power off.
While holding down the ‘STOP’ button on the Printer, turn the Printer back on.
Keep holding down the ‘STOP’ button until all the LEDs turn orange.
Then release the ‘STOP’ button, and press it again, one more time.

1. How to Upgrade
Please make sure to check the printer model number before performing the firmware upgrade.
2. Release Notes
Improved on light printing quality at low temperature environment
Automatic error recovery at abnormal operation
Toner save mode by optimized toner supplying
3. Caution
After firmware upgrade is completed, green LED lights will light up.
Do not turn off the printer before green LED lights turns on. A power interruption will corrupt the process.
If the printer is connected by a USB cable, disconnect all other USB devices, except your keyboard & mouse, from the computer.
If possible, be certain the Printer is connected to a BackUPS

Firmware Update Confirmation Instruction
Model CLP-300 series
When firmware upgrade is started, status LED light will start blinking.
As the printer reinitializes, status LED light will automatically turn off and then on.
Firmware upgrade is complete when status LED stays on green.

After firmware upgrade is completed, the LCD will display the message ‘Ready Copy’ and the LEDs will stay on green.

4. If there is an Error after firmware upgrade
If LED is on red or blinking after firmware upgrade, set-up download mode again and re-try the firmware upgrade.

Oct 20, 2008 | Office Equipment & Supplies

Not finding what you are looking for?
Office Equipment & Supplies Logo

Related Topics:

43 people viewed this question

Ask a Question

Usually answered in minutes!

Top Office Equipment & Supplies Experts

kakima

Level 3 Expert

102366 Answers

jasbo
jasbo

Level 3 Expert

2237 Answers

yadayada
yadayada

Level 3 Expert

76132 Answers

Are you an Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...