Question about Hotpoint Dryers

1 Answer

Hotpoint condenser dryer drum workinbg no heat


hotpoint condenser dryer drum rotating but no heat. All three heater element havre been ringed through with a meter and all are working o.k.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 38 Answers

Check the temperature switches in the back for continuity and also the moisture sensor on the exhaust housing at the rear of the unit. all these switches should be normally closed.
good luck...jay

Posted on Apr 24, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Dcvh660ghbb dryer wont heat


First check to see that the exhaust venting line is clear (not full of lint) as well as the path in the dryer to the line. This is the most common cause of no heat.
Second set the knob to heat turn on dryer with the lights off and the door open but the "open door" switch so that it still rotates with the door open. Look at the back of the rotating drum for a orange/red glow behind the drum (the heater coils). If there is no glow the heater coils are probably broken.
As the dryers age, the amount of thermal cycles the heater elements go through until the point when the coil wire breaks. There usually two heater coils behind the rotating drum (one hotter than the other and when combined the hottest heat temperature setting. You will need to pop open the top where you see the belt that turns the drum. The belt is removed from the spring loaded tensioner pulley at the base of the dryer. Then you can lift the drum out to get to the heater coils. Since no heat, both should be broken and will require replacement.

Sep 05, 2013 | GE Dryers

2 Answers

No high heat in dryer


This type of dryer has 2 rows of elements. If one is out then you will not have high heat.


Basically to get into ge dryers your start by popping the top then removing the front. Then the drum comes out.

Dec 05, 2012 | GE Dryers

2 Answers

Dryer does not heat


Might be a limit or a the heater element.MY REPAIR PAGE

Aug 15, 2012 | GE Dryers

2 Answers

How to replace ge dryer heating element


you will need to remove the drum for this one.  once it is out, the element is mounted on the back of the unit.  not a hard repair, just lay out the parts as you take it apart to give you some order as you re-assemble it.

Aug 03, 2010 | GE Profile Wizard DPSE592EAWW Electric...

3 Answers

No heat


Most likely you have a burnt element....A good handy man could replace the element fairly easily.. Cost of a new element about $50-$75

Apr 20, 2010 | GE DVLR223 Dryers

2 Answers

Dryer does not work drum rotates but does not dry on hotpoint aquarius washer dryer model wd64. all other functions operate ok


Probably open circuit heater element, or thermostat/s
Remove top cover, and you will see the heater manifold on the top of the drum.
It is a long aluminium box.
The element and stats are located here..
You will need a meter to test the appropiate components for continuity.
Please rate my solution.
Thanks.

Nov 22, 2009 | Hotpoint Aquarius WD640 Front Load...

1 Answer

Have a Hotpiont condenser dryer and the drum is live. (gives me an electric shock when touched) Please help .


Moist or water on the heater element is most common. Dismount heater cover dry out, then plug in and try. Or loose cable touching the chassie.

Jul 15, 2009 | Hotpoint Dryers

1 Answer

Elements over heating on hotpoint ctd00 condenser dryer


Did you check the fuse in your unit ?

Check the fuse whether it is burned.

Mar 13, 2009 | Hotpoint Dryers

1 Answer

Hotpoint dryer takes 3-4 70 minute cycles per load to dry, no matter what size load


Check your rear exhaust vent for blockage.
Your dryer has 2 heating elements.
If it gets warm at all at least one element is broken.
The operating thermostat could also be bad.
Burned/broken wire at heater terminal.
Unplug the dryer.
Remove the front panel, then the belt and drum and inspect the heater and thermostats.

Feb 22, 2009 | Hotpoint Dryers

Not finding what you are looking for?
Dryers Logo

Related Topics:

324 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hotpoint Dryers Experts

Gerry Harvey
Gerry Harvey

Level 3 Expert

1456 Answers

Chris Hall
Chris Hall

Level 3 Expert

842 Answers

shaun taylor

Level 3 Expert

1525 Answers

Are you a Hotpoint Dryer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...