Question about JBL Car Audio & Video

Open Question

Need the wiring diagram for JBL speaker and amp JBL 86150-04030

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

SOURCE: Wiring Diagram

First, try looking here: http://www.crutchfield.com/learningcenter/car/amplifiers_movie.html If that helps, be sure to leave feedback or I don't get paid. Look all over the cruchfield page and you can find guides for every type of installation.

Posted on Oct 03, 2007

Ad
sparky1500
  • 1066 Answers

SOURCE: JBL Sub Amp Wiring Please

it seems rather redundant to bridge a mono amp. Unless the instruction manual states otherwise, i would assume that one speaker output is identical to the other (ran in parallel, like an A or B speaker, not like Left or Right), and you would present the amp with a two ohm load by wiring one speaker to each output. Bridging it may or may not work, but, again, it just seems redundant.

Posted on Mar 01, 2008

  • 122 Answers

SOURCE: i got a stock ford JBL amp with no wiring diagram

ok on most amps there are two sets of wire ports one for speakers & one for +12v,grd & 12v remote start if you look over each port it will say what port is for what wire if it is in a connector it gets slightly more complecated what you do is with a vm check from wire to chassis ground [like seat bolts] 12v with key off when you cet power isolate wire then turn key on till radio comes on then do the same test for 12v isolate that will be remote start then turn key off &check from the first wire to other wire for ground to find speaker wires connect a regular peace of wire to chassis grd & touch the wires you will here the speaker pop be sure not to hold the wire on long cause it will blow the speaker

Posted on Jun 04, 2009

rteemon
  • 578 Answers

SOURCE: jbl bpx2200.1

and wht happen

Posted on Jun 26, 2009

catally733
  • 117 Answers

SOURCE: I have a JBL/Ford factory installed amp that I

www.metra.com u need the harness bypass kit for factory amp , or run wires from each speaker to amp you want to use

Posted on Jan 16, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Wiring diagram for 2004 toyota 4runner with jbl


It appears that red is a speaker connection and not power. The complete wiring diagram I'd in the link below.

speaker wire color Toyota 4Runner Forum Largest 4Runner Forum

Jan 26, 2014 | Toyota Cars & Trucks

2 Answers

Jbl audio wiring diagram/schematics/color codes/ect.ect.ect.


http://documents.victorytechnologies.com//documents/product/2322.pdf

Mar 15, 2010 | JBL BP1200.1 Car Audio Amplifier

2 Answers

I got a stock ford JBL amp with no wiring diagram i need to know what wires are what i have tryed to test for the power wirer but no luck.


ok on most amps there are two sets of wire ports one for speakers & one for +12v,grd & 12v remote start if you look over each port it will say what port is for what wire if it is in a connector it gets slightly more complecated what you do is with a vm check from wire to chassis ground [like seat bolts] 12v with key off when you cet power isolate wire then turn key on till radio comes on then do the same test for 12v isolate that will be remote start then turn key off &check from the first wire to other wire for ground to find speaker wires connect a regular peace of wire to chassis grd & touch the wires you will here the speaker pop be sure not to hold the wire on long cause it will blow the speaker

Jun 04, 2009 | JBL BP1200.1 Car Audio Amplifier

3 Answers

Bloon Fuses!


You don't need schematics to replace the fuses.
Open the speaker unit by unscrewing the back. The fuses are located near the on/off switch assembly. Replace them and screw the the unit back together.
To avoid blown fuses, try lowering the volume.

Aug 18, 2008 | JBL EON 15-G2 Powered DJ Speaker With EQ...

1 Answer

Jbl wiring diagram


OK     

See you CPU's backside  you will find  two different speaker input saket (in green ,yellow or pink) fix your speaker pins in their colors   and the speaker will work

Dec 17, 2007 | JBL CREATURE II Computer Speakers

Not finding what you are looking for?
Car Audio & Video Logo

Related Topics:

63 people viewed this question

Ask a Question

Usually answered in minutes!

Top JBL Car Audio & Video Experts

Steve Sweetleaf
Steve Sweetleaf

Level 3 Expert

1144 Answers

yadayada
yadayada

Level 3 Expert

76073 Answers

Mark Skinner

Level 2 Expert

77 Answers

Are you a JBL Car Audio and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...