Question about Lavazza Espresso Point Capsule Machine

1 Answer

Our problem with the machine is every once and awhile the signal on the upper left side of machine that looks like a lightblub flashes and the machine does'nt work. It will stay on but not make coffee. Do it just need to be flushed out or is it a bigger problem.

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 8 Answers

When the light flashes it indicates that the 130 deg themostat is open, machine too hot, however this does not prevent the machine from making coffee. Does the pump turn on? Do you hear a vibrating noise? Can you get water or steam, if so, the pump or the 3way valve are defective. Also, if after inserting the capsule and making a selection nothing happens, replace the micro switch. Good luck

Posted on May 11, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1996 3500 sierra left signal causes all lights to flash


Well, you're dealing with a short. If the right turn signal only works the right side bulbs, you know you're issue must be in the switch. The only way left turn signal would light the right side, but the right signal would not light the left is if you added a diode, which I doubt is the case. So the switch itself is suspect. That or a wiring issue. If you just bought the truck, and this is an existing issue I'd suspect wiring. If it just started doing this I'd suspect the switch.


I would check to make sure someone didn't monkey with the wires and switch the left turn signal with the hazard lights or something (do your hazard lights happen to flash only the left turn signals?). If it has or had an aftermarket alarm you need to check their work and see what may be screwed up. Alarm systems often tap into the parking lights, which will look like all 4 turn signals, but are actually dimmer filaments. Flashing the parking lights would actually make your radio flash too, so I'm kind of leaning this way. Can't say for sure on limited information though.

Aug 16, 2016 | Cars & Trucks

1 Answer

2002 hd 1400 has a #2 code showing up will not clear


If you've got that Engine light coming On for 4 seconds, Off 4 seconds then On 8 seconds then out, its historic. (there WAS a problem that has now cleared)
If its On 4, Off 4 then remains On its a 'current' code.

I never heard of a #2 code.....they are read as a two digit code.

Here's one method some use to clear all codes:

Disarm alarm if so equipped.
Run/Off switch to OFF
Ignition Key: ON,OFF,ON,OFF,ON (and leave ON)
Press LEFT turn signal switch TWICE. Wait for 1 or 2 flashes..
Press RIGHT turn signal switch ONCE => turn signal will flash 1 time
Press RIGHT turn signal switch ONCE => turn signal flashes 2 times
Press RIGHT turn Signal switch ONCE => turn signals flash 3 times
Press LEFT turn signal switch ONCE. TROUBLE CODES WILL NOW BE DISPLAYED
TO CLEAR ANY CODES,,,=> PRESS & HOLD LEFT signal switch for 5 seconds. => turn
signal will now flash twice to confirm memory is clear.
Turn ignition OFF.

Sep 28, 2014 | Harley Davidson FLHX Street Glide...

1 Answer

LD ERROR CODE AND WONT DRAIN LID WILL LOCK


try any button sequences yet . try holding start button and a cycle button hold both down to reset

Apr 01, 2013 | Whirlpool Cabrio WTW6800W Washer

1 Answer

No audible sounds on turn signals, turn lights on, key left in ignition or seat belts


just had this happen to me awhile ago it was the left speaker once the left speaker goes out so do your sounds... just had a speaker put in it worked for awhile now I am having the same issue ...I started having trouble with the driver side door where it won't close I think it is a big problem in cobalts if you try to close it it will not close then try it again then it closes that might have something to do with the speaker going out again in my car... but listen to your speakers my solution is to check your left speaker that might be your culprit......hope this helps

Sep 30, 2012 | 2008 Chevrolet Cobalt

1 Answer

I just bought a 2003 road king classic and can not set the alarm. Can you tell the procedure?


Arming: Hold Fob button down until signals flash twice. The 'key' lamp on
the speedo will Blink to indicate the system is armed. If auto arming is
enabled, the key lamp will Stay continuously lit for 30 seconds after the ignition is turned off, then the system Will arm itself.

Disarming: 'Double-click' the Fob, the signals will flash once and the key lamp will stop flashing. If the Fob is lost or not working, the system can be disabled by entering the passcode. Without setting off the alarm, get the ignition switch to accessory, hold down both left and Right signal switches until the key lamp flashes rapidly, enter the first digit on the left And use the right as an 'enter' key, enter all five digits of the passcode and the system will Disarm, if you screw up, the alarm will activate and you will have to wait ten minutes.

Transport Mode: Allows the system to be armed with the motion sensors disabled for service, Trailering, etc. Turn the ignition switch on, arm with the Fob, turn the ignition off and Arm once again with the Fob. Signals will flash 3 times to confirm
arming, All other functions of the alarm system require entering the configuration mode. This is done by Disarming the system, run/stop switch in stop, flip the ignition switch on/off/on/off/on Then push the left signal button
twice. If power was disturbed to the alarm module, The sequence may have to be repeated to get into configuration mode. The system will respond by flashing out the module type code.
(1-TSM, 2-TSSM dom, 3-TSSM hdi)
Now that you are in the config mode, you can do the following.....

- To assign the Fobs, push the right once (one flash) then the left once (two flashes)
Then hold down the Fob button until the system recognizes it. Hold down the second
Fob until the system recognizes it. Both Fobs must be assigned at the same time.

- To assign a passcode, use the fob to send a disarm command, signal will flash once
To indicate the first digit, push the left signal button and the key light will flash out the Value of the first digit. Pushing the left button will advance the value up through 9 and Will start over at 1. When done setting the first digit, double click the fob again and The signals will flash twice to indicate the second digit, continue on through all five digits. Turn ignition off to exit.

- To adjust the sensitivity, use the fob to send an arm command (one flash) then push the Left signal button once. The signals will flash out the current setting, 1-4, push the left Button to advance the setting, turn ignition off to exit.

- To extract system trouble codes, press the right signal button three times,
pausing between Each press for the system to flash once, twice, and three times
respectively. Press the left signal button once and they signals will flash out two digit
codes. Press and hold the left button to clear all codes from memory, otherwise
turn ign off to exit.

- To enable auto arming, use the fob to arm the system twice, and press the
left button once. The system will flash the setting code, 1-disabled, 2-enabled. Press the left button to change The setting, turn ignition off to exit.

- To adjust between Sidecar mode and normal mode, push the right button
twice quickly, Then the left button once and the signal will flash out the current setting, 1-normal, 2-sidecar. Press the left button to change the setting, then turn the
ignition off to exit.

- To adjust the length of time delay before going into storage mode, use the fob to send an Arm command three times, then push the left button, the signal will flash out the current setting. 1-30 days, 2-60 days, 3-90 days, 4-disabled. Use the left
button to advance the setting and turn the ignition off to exit.


Aug 31, 2011 | 2003 Harley Davidson FLHRCI Road King...

1 Answer

My signal stack stopped letting me switch on my high beams and wont spray washer fluid anymore. also my signals only work on the passenger side whether i signal left or right, but when i put my hazards on...


Sounds like that multifunction unit is bad or you are looking at some wiring issue. I would recommend taking the few screws loose on the bottom of the steering column shroud and looking inside it for clues. If nothing, you're going to need a wiring diagram and start checking wires! Good luck.

Nov 17, 2010 | 2006 Dodge Ram

2 Answers

I bought an old timex indiglo watch it has a button on the right middle and left bottom, how do i adjust the date?


Thank you for contacting FixYa.
  • Press the button on the lower right side of your Indiglo watch to unlock the mode function of the watch.
  • 2 Press the button on the lower left side to move through the modes. Each time you are in a mode, the digital display will flash. For example, when the time display begins to flash, you are in the correct mode to set the time.
  • 3 Change the time (or date) by pressing the button on the upper right side to advance the numbers or the button on the left side to move the numbers down. When you do this, you will be changing the first set of numbers (the hour or month, for instance); to change the minutes, press the button on the right side of the face until the second set of numbers is flashing and begin the process again.
  • 4 Press the button on the lower left side of the watch to save your settings. The button on the upper left side of the watch is not used in this process--it is the switch to turn on your Indiglo light.

  • Best regards. Jewel

    Sep 08, 2010 | Timex Watches

    2 Answers

    My left turn signal goes too fast when i want to make a left turn but my right turn signal is fine... how do i make the left one normal again?


    Replace the burned out bulb. It is flashing fast to alert you that bulb is burnt out. Turn on the side that works properly & note all bulbs flashing in front, rear & side. Most likely there is at least 1 burnt out on the other side.

    Jun 25, 2010 | 2001 Cadillac DeVille

    1 Answer

    I am pretty sure there is a relay bad on my focus for my signals. the left turn signal flashes faster than the right. Which one do i change?


    Howdy,
    First look for a burned out bulb on the side that flashes faster. Look carefully. Go to the right side that flashes normal and see how many bulbs flash front side and rear. then turn to left side and look, you may find one bulb burned out.
    Good Luck !!!!!!!!!!

    May 10, 2010 | 2000 Ford Focus

    1 Answer

    Turn signal flashes repeatedly


    Could be several things but generally this happens when one of the turn signal bulbs is burned out (front or back), especially if it is fast on one side (left vs right). Once the burned out bulb is replaced the flashing returns to normal.

    Apr 16, 2010 | 2000 Ford Econoline

    Not finding what you are looking for?
    Lavazza Espresso Point Capsule Machine Logo

    Related Topics:

    366 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Lavazza Coffee Makers & Espresso Machines Experts

    ray gallant

    Level 3 Expert

    44268 Answers

    nikolay nikolov

    Level 2 Expert

    123 Answers

    Tom Chichester

    Level 3 Expert

    34731 Answers

    Are you a Lavazza Coffee Maker and Espresso Machine Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...