Question about Fluke Networks Fluke VoltAlert 1AC-II High Voltage Tester

Open Question

Where are the batteries for volt alert 1lac-2

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Low charge alert wont stop


Go by a battery shop and get them to check your alternator. If you have a voltmeter, start the car and then check the battery voltage with the engine running. It should read 14----14.5 volts with the engine running. If it reads 12 ---13 volts, you have an alternator problem.

Apr 20, 2015 | Cars & Trucks

1 Answer

Internal battery 601


Replacing the bios battery will fix that.

Jul 14, 2014 | Computers & Internet

1 Answer

Labelled on march 29, 2011, and it beeps every 30seconds. what's the problem?


They beep to say that the battery isn't at its full potential (for all intensive purposes.... DEAD) You have to get the newest ALKALINE 9 volt battery that can be obtained to please these modern power hungry alarms.

Aug 22, 2013 | First Alert SA302 Dual System Smoke...

1 Answer

GE Simon says that the smoke alarm has a low battery. Replaced the batteries, and still receive the same alert. ???


I know some of this sounds obvious but the problem is usally related to 1 of 3 things.

1 Battery oreintation is wrong
2 Replacement batteries were old and were already below the low battery threshold (1.35 volts per battery/ 2.7 volts combined)
3 Didn't use the correct battery - manufacturer recommends lithium batteries (quality alkilines will work but they will have a shorter life)

Beyond this I will need more information to diagnose the issue.

Mar 19, 2010 | GE Security Simon 3 Wireless Home Security...

1 Answer

Need to make sure programmed


Program the Midland 74-109 Weather Radio
a) Turn unit on. Extend the antenna. Adjust volume up slowly; Do you hear anything? If not, try replacing the 9 volt battery with a fresh one, in the accessible battery compartment underneath the unit. Repeat above steps.
b) If no sound is heard, turn unit over and look for "WEATHER" slide switch on bottom. With unit on & volume adjusted to comfortable hearing level, slowly slide switch down (or up) through various frequencies [1)162.550, 2) 162.400, 3) 162.475, 4) 162.425, 5) 162.450, 6) 162.500, 7) 162.525] until voice transmissions are heard. This should be the closest National Weather Service (NWS) broadcast for your area. Check the NWS website at http://www.nws.noaa.gov/nwr/nwrbro.htm for your state, click on the state name, and look for the site name or site location nearest you. The frequency for that site should be the strongest, and appropriate for your area.
c) You can set the alert tone, for special weather alert broadcasts, on the bottom of the unit on the slide switch marked "ALERT". Set the switch to the desired type of alert: 1) LED [LED on top of unit (marked ALERT) lights up when alert is broadcast-no siren tone/alarm is heard] 2) LED & ALARM [LED lights up and alarm/ siren tone is heard] 3) VOICE [LED on top of unit lights up and voice broadcast is heard, only; no siren tone/alarm is heard].
d) Be sure to press the "ALERT" button on top of the unit and leave the volume at a comfortable listening level to hear weather alerts for your area (Alert LED on top of unit lights up to show Alert function is active). You can test the present volume level by pressing the "TEST" button. Be sure to press the "ALERT" button again after listening to the volume level to re-set the Alert function. You can listen to weather broadcasts anytime, by pressing the "WEATHER" button. After listening, be sure to re-press the "ALERT" button to reset the Alert function.
e) 9 volt battery life should last about 6 to 7 months, depending on how much unit is used an number of alerts received. Replace battery every 6 months, or when you replace your smoke alarm battery, or at beginning and end of daylight savings time. A 12 volt AC adapter to replace the battery, can be used. One should have been supplied with unit. If not, a replacement can be found at Radio Shack.
f) This should complete your Midland Weather Alert Radio Model 74-109 programming.

Apr 09, 2009 | Midland 74-109 Weather Radio

1 Answer

Battery light alerts when car is driving


The thing that sucks about the Sebring, I have a 2001, is that if there is a problem and your car detects it 3 times, it will stay programmed in the onboard diagnostic, even if you have repaird it. The only way to have that little light go out, is for someone to reset the onboard diagnostic computer with the fancy machine code reader that only the shops seem to have. So, have it reset.

Jul 25, 2008 | 2001 Chrysler Sebring

1 Answer

Not receiving alerts anymore...


My wr-100 came with a special note inserted with the instructions that the WR-100 was programmed to not give off an audible alert on tests. This is to supposedly protect you from thinking you have a real emergency. Mine is new. Maybe the older ones had an audible test alert. I assume yours gave an alert at one time??

Feb 06, 2007 | Midland WR-100 Weather/RDS Radio

Not finding what you are looking for?
Fluke Networks Fluke VoltAlert 1AC-II High Voltage Tester Logo

Related Topics:

45 people viewed this question

Ask a Question

Usually answered in minutes!

Top Fluke Networks Measuring Tools & Sensors Experts

Vuk B

Level 3 Expert

683 Answers

Trevor Turner

Level 2 Expert

208 Answers

joseph m fucci
joseph m fucci

Level 1 Expert

43 Answers

Are you a Fluke Networks Measuring Tool and Sensor Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...