Question about Peavey Electronics Peavey PV10 Mixer

1 Answer

I want to know how to connect a powered subwoofer to the peavey 10 mixer

Posted by on

  • Rick Morris
    Rick Morris Dec 20, 2013

    All hooked up and work's fine. Thank's everybody for the help.

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Champion:

    An expert who has answered 200 questions.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 243 Answers

Connection is hooking up from mixer's main outputs (L,R) to
Subwoofer amp inputs.

Posted on Nov 07, 2013

  • Rick Morris
    Rick Morris Dec 20, 2013

    Sorry i have'nt got back to. Your solution worked. Thank's

×

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 17 Answers

SOURCE: i have the peavey xr

That's easily done. Simply connect the left(or right) output of your mixer to one of the channels on the peavey. Use any line input. Since the peavey is a mono system, there's no need sending a stereo mix to it.

Posted on Mar 09, 2011

  • 4234 Answers

SOURCE: can i connect the pv 112 to the pv 118 subwoofer

Generally speaking you should only send low frequencies to subs. The highs, while lower in power than the lows, will over time harm the voice coils. The ideal way to do this is to use an external crossover netween the main output and the amp input with the higher range going to a general set of speakers. Send the lows through the second channel of the amp and then to the subs.

In short, while not recommended, yes you can hook them up in parallel.

Dan

Posted on Dec 10, 2010

  • 5603 Answers

SOURCE: My Peavey PV-118 18" subwoofer

Peavey uses a protection network and sometimes it gets blown when too much power is sent to the speaker. The speaker may be blown however. Peak power for this is 800 Watts and 400 Program... That is NOT RMS power. Make sure your amp is no bigger than 300 Watts RMS driving this. If you are REAL lucky, maybe a lead has fallen off the speaker... Open the unit inspect and test the components.

Posted on May 16, 2011

  • 5603 Answers

SOURCE: How do i hook a

You CAN drive the power amps from the main amp inout jacks BUT the rest of the inout of the 8600 would be dead then. You can connect the L and R from the FX24 to either the media RCA jacks or into the channel9/10 jacks. FOr the latter, use TRS cables. Leave the two selection buttons in the up position.

Posted on Sep 22, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How do I connect my Bose l1 compact to Peavey xr 8600?


You would come out of the Main output on the front of the mixer into the line in on the Bose.

You may find this site useful- L1 Unofficial Performers Guide

Jun 25, 2015 | Peavey XR 8600D Class D Powered Mixer

1 Answer

I want to record using Tascam with my peavey xr1220 mixer


What Tascam recorder are you using? If you are multitracking you will be unlikely to be able to use this mixer. Otherwise get a phono lead to fit the tape out and suitable connections for the Tascam recorder at the other end. This will allow you to record the main mix but unless you are a solo act or putting everything through the PA this will probably be pretty useless to you.

Jan 07, 2015 | Peavey XR 1220 Powered Mixer Mixer Powered

1 Answer

How do i hook a peavey fx24 mixer to a Peavey xr8600 with out going through the 8600's mixer? I am wanting to use the 8600 to power my mains and use another amp to power my monitors. can i do this?


You CAN drive the power amps from the main amp inout jacks BUT the rest of the inout of the 8600 would be dead then. You can connect the L and R from the FX24 to either the media RCA jacks or into the channel9/10 jacks. FOr the latter, use TRS cables. Leave the two selection buttons in the up position.

Sep 21, 2011 | Peavey Xr 8600 8 Channel Powered Mixer

1 Answer

Connect Qsc pair kw122 powered speakers and kw 181 powered sub to peavy pv14 mixer?


Two things... Use BALANCED LINES, either XLR or TRS... AND power the mixer from the same receptacle or power conditioner as the speakers and the sub.

Apr 30, 2011 | Peavey Electronics Peavey 00512140 PV 14...

1 Answer

I have the peavey xr 8600 and i wanna know how to connect an additional non powerd mixer to it ( i wanna use the peavey as an amp??


That's easily done. Simply connect the left(or right) output of your mixer to one of the channels on the peavey. Use any line input. Since the peavey is a mono system, there's no need sending a stereo mix to it.

Mar 08, 2011 | Peavey Xr 8600 8 Channel Powered Mixer

1 Answer

Can i connect the pv 112 to the pv 118 subwoofer since the powered mixer i bought it only has 2 main outputs? The powered mixer I bought is the PV XR 8600D powered mixer...


Generally speaking you should only send low frequencies to subs. The highs, while lower in power than the lows, will over time harm the voice coils. The ideal way to do this is to use an external crossover netween the main output and the amp input with the higher range going to a general set of speakers. Send the lows through the second channel of the amp and then to the subs.

In short, while not recommended, yes you can hook them up in parallel.

Dan

Dec 09, 2010 | Peavey Pv118 1x18" Subwoofer Speaker...

1 Answer

Hi. I have a Peavey xr800f. Where can I connect a 400 W active subwoofer?


If the subwooofer has only a single input, then connect it to the Monitor output which does a mix, HOWEVER the level will NOT vary with the main sliders, but only with the monitor pots... This is NOT really practical for performances.

There is no mixer built in the unit, so you might make a simple resistive mixer taking the "Master out" left and right using 1K ohm resistor from each to a common point that feeds the subwoofer. Tie the grounds of the sub and mixer together.

FOR SYSTEM SAFETY always power the mixer and active speakers or any interconnnected equipment from the same receptacle or source.

Aug 21, 2010 | Music

Not finding what you are looking for?
Peavey Electronics Peavey PV10 Mixer Logo

Related Topics:

98 people viewed this question

Ask a Question

Usually answered in minutes!

Top Peavey Music Experts

Ben Armstrong

Level 2 Expert

334 Answers

Vito Vacirca Jr.

Level 2 Expert

140 Answers

Lawrence Nentwig
Lawrence Nentwig

Level 1 Expert

8 Answers

Are you a Peavey Music Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...