Programming how to

Tuning to radio stations

1. 1 Select TUNER source. ? TUNER is displayed briefly.
2. 2 Press BAND once or more to select your
   waveband.

1. 3 Press down on TUNING a? or a? and release button.
   ? The radio automatically tunes to a station with sufficient reception. Display indication during automatic tuning: SEARCH.? If a FM station is received in stereo, STEREO is shown.
2. 4 Repeat step 3 if necessary until you find the desired station.

To tune to a weak station, press TUNING briefly and repeatedly until you have found optimal reception.


Programming radio stations
You can store up to a total of 40 radio stations in the memory.
Automatic programming
Automatic programming will start with a chosen preset number. From this preset number upwards, former programmed radio stations will be overridden.The system will only programme stations which are not in the memory already.
Press PRESET 3 or 4 (on the remote control ¡ or TM ) to select the preset number where programming should start.
Note:
- If no preset number is selected, default is preset (1) and all your presets will be overridden.
Press PROGRAM for more than 2 seconds to activate programming.? AUTO is displayed and available stations are programmed in order of waveband reception strength: FM followed by MW and LW.The last preset automatically stored will then be played.
Manual programming
Tune to your desired station (see "Tuning to radio stations").
Press PROGRAM to activate programming. ? PROGRAM flashes in the display.
Press PRESET 3 or 4 (on the remote control ¡ or TM ) to allocate a number from 1 to 40 to this station.
Press PROGRAM again to confirm the setting. ? PROGRAM disappears, the preset number and the frequency of the preset station are shown.
Repeat the above four steps to store other stations.

Maybe the sprinkler head is not advancing.

Your Use and Care Manual can be found here:

http://useandcares.hamiltonbeach.com/files/840160001.pdf

See page 7 of the pdf for illustrated instructions on setting the clock and programming.

Sorry to read about your problem, I hope this helps you out.

ProgrammingBrewTemperature (187°-192oF)
The Brewer brews at a preset temperature of 192°. You can adjust this temperature down by 5 degrees if you prefer a cooler cup of coffee, tea or hot cocoa. Simply follow the instructions below.
1. Press the Menu Button on the LCD Control Center five times to program the Brew Temperature feature.
2. The LCD Control Center will now display the programming options with a small arrow next to "SET BREW TEMP" (fig. 15). Also, the temperature 192° (initial setting) will be displayed at the bottom of the LCD Control Center to indicate the current temperature setting.
3. A minus sign will appear over the Small Cup Button and/or a plus sign over the Large Mug Button. Use these buttons to raise or lower the temperature one degree at a time.
4. Once you have reached your desired brew temperature, press the Menu Button once to exit the programming mode. "BREW TEMP SET" will be displayed in the LCD Control Center if you have changed it from 192°.
5. To change the brew temperature again, repeat steps 1 through 3 to change the temperature up or down, remembering that the temperature can only be between 187° and 192°.

I tried to help you. Please help me and Rate/Vote on my response, thanks and good luck

"How can I program my electronic keypad lock when the instructions with the Programming Code have been lost?"
The back plate of the keypad side of the lock on the exterior of the door has a sticker which includes the serial number, six digit programming code and two pre-programmed four digit user codes. The lock must be disassembled to a point the exterior of the lock can be pulled away from the door and the information on the sticker made note of.

Complete installation & programming instructions can be found here:

http://consumer.schlage.com/Project%20Documents/P515-858.pdf

Notice that the above is a .pdf filetype. That means that you need to have Adobe Reader or similar installed on your computer to view it. So if you are unable to view the file, download (for free) and install Adobe Reader first. You can get it here:

http://get.adobe.com/reader/

Videos for installing and programming can be found on this page:

http://consumer.schlage.com/Service-Support/Pages/InstructionandManuals.aspx

Scroll down and find them under the heading Electronic Security--Keypad deadbolt 365

Good luck--and please provide feedback if this helps!

Try completely unplugging your pot and then plugging it back in. It is possible that this will reset the programming in your coffee pot. If this doesn’t work, I recommend calling Brevell customer service and they will either help you or probably send you another pot.

Way too easy :-)

When you were listening to messages you probably pressed the SKIP button for longer than 2 seconds. Try pressing it and holding it again and see what happens.

Here's the manual link: http://www.home-electronics.net/ge/pc/IB/25942GE3_IB.pdf

Carl

I got one of these for xmas, and I was able to program the pre-brew option.

First, turn off the machine.
On the front of the machine, there is series of 5 buttons. (From left to right, they are: Small Coffee, Large Coffee, Pre-ground Coffee, Hot water and Descaling.)

While holding down the 1st (Small coffee) and 4th (Hot water) buttons, turn on the power.
Wait 3-5 seconds before releasing these two buttons. You machine is now ready for programming.

Below the 5 buttons are 4 small lights. If the second light from the left is red, the machine is already programmed to pre-brew. If the light is not red, do the following:

Press the Coffee button (2nd button from the left) once and the second light from the left should glow red. This turns on pre-brewing. (Pressing the Coffee button again will turn off both the light and the pre-brew option.)

Now turn off the power for at least 5 seconds. The next time you turn the machine on, it should pre-brew the coffee.

The process worked great for me the first time, but when I wanted to program the machine to not pre-brew, I had to go through this process a couple of times. Not sure why, though. :-)

Kathy