Question about Kenmore HE2 Plus Front Load Washer

2 Answers

Kenmore F-01 error - Kenmore HE2 Plus Front Load Washer

Posted by on

  • Mark Nichols May 11, 2010

    f 1 usually means the board is fried find me the model and get back to me here or on my site there is a phone number there.

×

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 3,230 Answers

Hi there,

The F01 fault code is indicating an EEPROM error or a PUMP DRIVER error. A communication error between the Central Control Unit (CCU) and the EEPROM on board the CCU occurred.

Possible causes of an EEPROM error:
A power glitch may have caused this error. Unplug the power cord for 3 minutes then reconnect power.

Possible causes of PUMP DRIVER error:
The pump driver fails to activate. Replace the the CCU board.

Most likely the CCU board will need to be replaced.

Good Luck!!

Thanks

Posted on Aug 09, 2009

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 460 Answers

F1
Possible Cause / Procedure
*A power gitch may cause this error
-Unplug washer or disconect power for 2 minutes.
-weryfy CCU operation by running a Diagnostic Test or any cycle
==================PUMP DRIVE ERROR==========
* Replace CCU board.
==================
MAIN RELAYS ERROR
= MEANS; one of the main relays is not working properly======
possible
====Causes=====The relay might be soldered or always open.
===== Procedure ====Replace CCU board This is a Technicion that must work on it.
Sorry

"Was this helpful?"

Posted on May 11, 2009

  • 3 more comments 
  • VIRGINIA MARTINEZ
    VIRGINIA MARTINEZ May 11, 2009


    F1

    Possible Cause / Procedure

    *A power gitch may cause this error

    -Unplug washer or disconect power for 2 minutes.

    -weryfy CCU operation by running a Diagnostic Test or any cycle

    ==================PUMP DRIVE ERROR==========

    * Replace CCU board.

    ==================

    MAIN RELAYS ERROR

    =======one of the main relays is not working properly======

    POSSIBLE

    ====Causes=====The relay might be soldered or always open.

    ===== Procedure ====Replace CCU board wish a technition service must work on it.

    Am sorry

    "Was this helpful?"

  • VIRGINIA MARTINEZ
    VIRGINIA MARTINEZ May 12, 2009

    code 01
    EEPROM ERROR

    Means a communication error between the Central Control Unit(CCU)and the EEPROM onbord the CCU ocurred

    *Unplug washer or disconect power for two minutes.
    *If the error still exist you need to call a technition to replace the CCU bord.



    Did I answer your question?

  • VIRGINIA MARTINEZ
    VIRGINIA MARTINEZ May 13, 2009

    F1
    Possible Cause / Procedure
    *A power gitch may cause this error
    -Unplug washer or disconect power for 2 minutes.
    -weryfy CCU operation by running a Diagnostic Test or any cycle
    ==================PUMP DRIVE ERROR==========
    * Replace CCU board.
    ==================
    MAIN RELAYS ERROR
    =======one of the main relays is not working properly======
    POSSIBLE 
    ====Causes=====The relay might be soldered or always open.
    ===== Procedure ====Replace CCU board wish a technition service must work on it.
    Am sorry 
    "Was this helpful?"



  • VIRGINIA MARTINEZ
    VIRGINIA MARTINEZ May 13, 2009

    F1
    Possible Cause / Procedure
    *A power gitch may cause this error
    -Unplug washer or disconect power for 2 minutes.
    -weryfy CCU operation by running a Diagnostic Test or any cycle
    ==================PUMP DRIVE ERROR==========
    * Replace CCU board.
    ==================
    MAIN RELAYS ERROR
    =======one of the main relays is not working properly======
    POSSIBLE 
    ====Causes=====The relay might be soldered or always open.
    ===== Procedure ====Replace CCU board wish a technition service must work on it.
    Am sorry 
    "Was this helpful?"



  • VIRGINIA MARTINEZ
    VIRGINIA MARTINEZ May 14, 2009






    F1 EEPROM ERROR



    A communitcation error between the Central Control Union (CCU) and the EEPROM ondoard CCU occurred.



    Possible Cause / Procedure

    *A power witch may cause this error

    -Unplug washer or disconnect power for 2 minutes.

    -verify CCU operation by running a Diagnostic Test or any cycle.



    some diagnosticst must be done by a technician service .



    Was this helpful?


×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Sears Electric Dryer is flashing F01 What is wrong?


The F01 indicates a failed electronic machine control board. This error code can sometimes be caused by a glitch or power surge through the electrical lines. You may be able to clear this code by unplugging the washer for 5 minutes. If the code returns after plugging the washer back in, then the electronic machine control board will need to be replaced.
You can order a new control board from the Sears PartsDirect website.
http://www.searspartsdirect.com/partsdir...
Here's how to do it: http://media.fotki.com/1_p,wkwdftgtbkdgf...


Error code on dryer F01 - Kenmore Elite HE3 Dryer - iFixit

https://www.ifixit.com/.../Error+code+on+dryer+F01 Traduire cette page The F01 indicates a failed electronic machine control board. This error code can ... The Kenmore Elite HE3 is 7.2 cu. ft. capacity electric dryer by Kenmore.

Dryer Sears / Kenmore HE3 - F01 Error Code Main Circuit ...

2q==? 7:35 https://www.youtube.com/watch?v=eWqrn5klxm0 20 avr. 2015 - Ajout? par Jim Dandy Sears Kenmore Dryer Model HE3 - F01 Error Code. Main Circuit Board Repair - Electronic Control Board ...

Error code F1 on Kenmore HE2 electric dryer appeared ...

www.shopyourway.com > ... > Questions Traduire cette page Sears Kenmore HE2 electric dryer; model #11087571601. F1 error message appeared ... Power it back up and see if you still get the F01 error code. If not, then I ...

What does the error code F-01 mean on my Kenmore front ...

www.shopyourway.com > ... > Questions Traduire cette page By unplugging and plugging in the electrical cord, I got the dryer to work again. ... What does the error code F-01 mean on my Kenmore front loaded HE2 dryer? ... My kenmore washing machine 110.46462500 is flashing an error code F.01 ...

Error code on dryer F01 - Kenmore Elite HE3 Dryer - iFixit

https://www.ifixit.com/.../Error+code+on+dryer+F01 Traduire cette page The F01 indicates a failed electronic machine control board. This error code can ... The Kenmore Elite HE3 is 7.2 cu. ft. capacity electric dryer by Kenmore.

Dryer Sears / Kenmore HE3 - F01 Error Code Main Circuit ...

2q==? 7:35 https://www.youtube.com/watch?v=eWqrn5klxm0 20 avr. 2015 - Ajout? par Jim Dandy Sears Kenmore Dryer Model HE3 - F01 Error Code. Main Circuit Board Repair - Electronic Control Board ...

Error code F1 on Kenmore HE2 electric dryer appeared ...

www.shopyourway.com > ... > Questions Traduire cette page Sears Kenmore HE2 electric dryer; model #11087571601. F1 error message appeared ... Power it back up and see if you still get the F01 error code. If not, then I ...

What does the error code F-01 mean on my Kenmore front ...

www.shopyourway.com > ... > Questions Traduire cette page By unplugging and plugging in the electrical cord, I got the dryer to work again. ... What does the error code F-01 mean on my Kenmore front loaded HE2 dryer? ... My kenmore washing machine 110.46462500 is flashing an error code F.01 ...

Feb 04, 2016 | Sears Kenmore Elite Electric Dryer 69278

1 Answer

What does code F 01 mean


For a start, google "Kenmore Dryer Model xxxxx error code F 01"
where xxxxx is the model of your dryer. Sift through the hits for an answer.

Pete

Sep 28, 2015 | Kenmore Dryers

1 Answer

Resetting a F 01 error repair.


F 01 is a bad control board, you dont reset, replace board

Oct 06, 2014 | Kenmore HE2 Plus 3.6 cu. ft. Front-Load...

1 Answer

What does this error mean dryer has error f-01?


The "F1" error means that the dryer's thermistor failed and needs to be replaced. Make sure you check the dryer vent for clogs before installing the new part.

May 04, 2014 | Kenmore Dryers

1 Answer

110.4753 error code f01


I found this on the WEB-In reference to your Kenmore HE washer, model number 110.4753:

F-01 Error code

:

EEPROM ERROR

,

PUMP DRIVE ERROR

, or a

MAIN RELAY ERROR

EEPROM ERROR

: A communication error between the

Central Control Unit

(CCU) and the

EEPROM

onboard the

CCU

occurred.

PUMP DRIVE ERROR

: The pump driver fails to operate

MAIN RELAY ERROR

: One of the main relays is not working properly

Mar 31, 2014 | Kenmore HE2 Plus Front Load Washer

1 Answer

I have a F-01 fault code on my Kenmore HE2plus front load washer. model # 11047512601. Sears talked me thru the software resets and still had the F-01 error. do I need to replace the Main Control Unit?


Hi,


The F01 fault code is indicating an EEPROM error or a PUMP DRIVER error. A communication error between the Central Control Unit (CCU) and the EEPROM on board the CCU occurred.

Possible causes of an EEPROM error:
A power glitch may have caused this error. Unplug the power cord for 3 minutes then reconnect power.

Possible causes of PUMP DRIVER error:
The pump driver fails to activate. Replace the the CCU board.
Most likely the CCU board will need to be replaced.

Thank you !!

Jun 28, 2010 | Kenmore HE2 Plus Front Load Washer

1 Answer

Kenmore oven-microwave 911 41479791 I get E 01 error.


F 11 code. it is a touch pad error.
If you just cleaned the control panel it may have water in the panel causing a key to stick.
If after a day or 2 it hasn't dried out - then you will need to replace the touch pad.

Visit www.searspartsdirect.com and enter in your full model number for a parts breakdown and schematics.

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question

Feb 18, 2010 | Kenmore 63662 / 63664 / 63669 Microwave...

2 Answers

Unit will not run.


Error code 01 - unit has a sealed system leak; most warranties are 5 years.

Dec 30, 2009 | Kenmore 54701 Dehumidifier

2 Answers

Kenmore he2 electric dryer error code f-01


always unplug for 10 minutes and retry first.

Jun 12, 2009 | Kenmore 82822 Electric Dryer

Not finding what you are looking for?
Kenmore HE2 Plus Front Load Washer Logo

1,617 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenmore Washing Machines Experts

Sal DeAngelo

Level 3 Expert

2180 Answers

fordexpert

Level 3 Expert

5520 Answers

Ed Mac

Level 3 Expert

731 Answers

Are you a Kenmore Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...