Question about Abit IP35P Motherboard

1 Answer

VIA CPU to AGP Problem with 3Gb and Vista


Hi,

I would be grateful if someone could please help me with the following problem I am experiencing with my PC which I have been fighting for months now!

My system was purchased from Evesham in 2003, and has a KT4V motherboard which can hold up to 3Gb RAM, a Radeon 9700 Pro graphics card, with an AMD XP processor. In March last year I installed a new hard disk and installed Vista Home Premium. At this time, I had no issues.

Recently I upgraded the RAM to the maximum amount (3Gb). All RAM chips are from Crucial, each 1Gb. I have three slots with 1Gb in each. All modules are DDR333(cl2.5).

When the system runs on only 2Gb RAM, there are no issues and the 9700 graphics card works fine, however when running on 3Gb (i.e. all slots occupied), the system fails to boot properly into Windows. Stops on the Blue Screen of Death with

“STOP 0X00000116 “ and complains about atikmdag.sys”

When looking in Device Manager, under System Devices, there is a problem with the VIA CPU to AGP Controller. The device gives the following error message:


“This device cannot find enough free resources that it can use. (Code 12)
If you want to use this device, you will need to disable one of the other devices on this system.
Click 'Check for solutions' to send data about this device to Microsoft and to see if there is a solution available.”

At this time, the 9700 graphics card cannot be seen in Device Manager and is not being used.

When disabling the VIA CPU to AGP Controller, with 3Gb of RAM, the system boots normally and seems to work fine, but the Radeon Pro 9700 card is not showing up in Device Manager and is not being used (presumably because the VIA CPU to AGP Controller is disabled).

When the system is running on 2Gb of RAM, it boots normally and there are no problems in Device Manager (VIA CPU to AGP Controller works fine, Radeon 9700 card listed and working fine). Note, when I put one of my old 256MB modules in slot 3 (giving 2.25 Gb) the system works fine.


I have re-installed Vista, unplugged all other PCI devices, cleared CMOS, upgraded my BIOS to the latest, installed Version 5.14A of the Hyperion Pro drivers from VIA and installed the latest drivers from Ati for the Radeon 9700 PRO card. – but sadly no joy!

I have noticed that after installing the VIA CPU to AGP Controller driver (XP diver in 5.15A of Hyperion 4 in 1 drivers), it works fine (with the 3Gb in place). In Device Manager it is now shown as: VIA CPU to AGP 2.0/ AGP 3.0, however, the problem now is that the Radeon Pro 9700 card doesn’t work. I installed the latest driver from ATi (7.12 20/12/07), however in Device Manager this is showing a problem with the following message:

“Windows has stopped this device because it has reported problems. (Code 43)”.

Any help would be greatly appreciated with regard to what I should do to resolve this / what drivers I should install / order of installation etc….. anything!!!

I just can’t understand why all works fine with 2Gb but not with 3Gb!

Am I correct in saying, when a driver doesn’t exist for Vista, you still shouldn’t use the XP one?......but instead, accept the Microsoft provided driver which came with Vista)?

Thanks in advance,
Neil. Idential problem but with different hardware. Same problem occurs with XP32, XP64, Vista32 and Vista64 with an nVidia card and 3GB RAM and an IP35 pro mobo. (Also get problems with ATI cards too... so confused with this I 'm stumped). When I take out the 512mb stick, leaving 2.5gb, and hey presto, a stable system. WTF?


Posted by on

  • originuk Apr 22, 2009

    Hi there,
    Thanks for your input on this .... I've got 2 x 1gb sticks, and 2 x 512mb sticks.... I've alternated the two 512mb sticks to rule out a memory problem. No joy. :-(




×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 519 Answers

Hi,
Chances are good that your third 1gig memory module is faulty. Windows blue screen of death at startup is a typical symptom of faulty RAM memory.
Try replacing the third 1gig DIMM with another of the same type.
Let me know if this works or not.
Regards,
Graemevm

Posted on Apr 22, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Kd7a drivers for windovs7/vista


Hello try the homepage:

http://abit.ws/page/en/download/download_driver.php@pFUN_KEY=9000&pTITLE_IMG=_2Fdownload_2Fimages_2Fdownload.html

Or the intel download site:

http://downloadcenter.intel.com/

And run the update utility.

Features

Processor
Supports AMD-K7 Athlon/ AthlonXP/ Barton FSB 200/266/333MHz Processors
Chipset
- VIA KT400A / VT8235CE chipset
- Supports Hi-Speed Universal Serial Bus (USB 2.0)
- Supports Advanced Configuration and Power Management Interface (ACPI)
- Accelerated Graphics Port connector supports AGP 8X /4X (0.8V /1.5V)
Memory
- Three 184-pin DIMM sockets
- Supports 2 DIMM Un-buffered DDR 333/400 (Max. 2GB)
- Supports 3 DIMM Un-buffered DDR 200/266 (Max. 3GB)
LAN
- On board 10/100M LAN
Audio
- 6-Channel AC 97 CODEC on board
- Professional digital audio interface supports optical S/P DIF Out.

You can`t use xp drivers for windows 7, it does not work that way.
This mainboard is from the year 2002, and you probably can`t find any drivers for windows 7.
The mainboard is too old, for the windows system.
Continue using windows xp, or buy a new mainboard or pc.

Good luck

Jan 17, 2013 | Abit IP-95 Motherboard

1 Answer

Deleted via cpu to agp controller


You can actually do a system restore to retrieve it. Go to start > programs > accessories > system tools > system restore

select the date when it was still there.

Dec 17, 2012 | Acer VIA CPU to AGP Controller

1 Answer

When I start my laptop I get the following message " The system bios has detected a possible issue with a cooling fan" and after a few seconds it turns itself off. I would be grateful for any...


The heat sink isn't properly connected to the CPU. If you're not comfortable opening up your computer then take it to your local repair shop. If you are, then open it up, remove the CPU and heatsink, remove the old thermal paste with goo gone, and apply a fresh layer of thermal paste, then reseat the CPU.

Jun 18, 2011 | HEWLETT-PACKARD HP G62 15.6" Laptop Intel...

1 Answer

Manyal


EP-8K3A
Introduction
KT333 with VT8233A AGPset/266MHz FSB/3 DIMM with DDR333/1 AGP-4X/6 PCI/USB1.1/ATA-133/6CH Audio/ATX
Specification
PROCESSOR:
The Socket A compatible AMD AthlonTM XP processor 1500+ to 2700+, 600MHz to 1.4GHz AMD AthlonTM and AMD DuronTM processor up to 1.3GHz
CHIPSET:
VIA KT333 AGPset (KT333+ VT8233A)
DRAM MODULE:
184pin DDR DIMM x 3 for PC2700 Memory
DRAM Size: 64MB to 3GB
EXPANSION SLOT:
PCI x 6!A4X AGP x 1
ONBOARD I/O:
Winbond W83697HF LPC I/O integrated with FDD, Parallel, Game, Serial and IrDA v1.0 and Power-On Controllers
ONBOARD PCI / IDE:
PCI Bus IDE Port with PIO / Ultra DMA-133 x 2 (Up to 4 Devices)
I/O CONNECTOR:
PS/2 Mouse and PS/2 style Keyboard
COM1, COM2, Printer, Audio-in/out, MIC & Game Port connectors
USB:
USB connector x 4 (2 for Opt.)
BIOS:
Award Plug & Play BIOS
Built-in AC97 Digital Audio (by Realtek ALC650):
Compliant with AC97 2.2 specification
6 channel slot selectable DAC output for multi-channel applications
Supports digital SPDIF Out Function
EXTENDED FUNCTION:
Supports Hardware Monitoring Function by W83697HF
Supports exclusive KBPO (KeyBoard Power On)
Supports CPU Vcore , Clock and Multiplier setting via BIOS
Supports Memory Voltage setting via BIOS
Supports STR (Suspend To RAM) power saving Function
Supports Wake-On-LAN Function
FORM FACTOR:
305mm x 245mm x 34mm ATX Size
OS Supported:
Windows 98SE/ME/2K/XP/Server2003

Jun 05, 2011 | EPoX EP-8K3A+ Motherboard

1 Answer

Hi i got ati radeon 9000 agp lost CD!!!!!!!!


You can get the drivers for this card from http://ati.amd.com

Apr 19, 2010 | ATI RADEON Graphic Card

1 Answer

Matrox millenium G450 AGP video card second monitor


i have problems for vista window . i instled vista wind in cpu but the main problems is grapics ( cpu model is intel d450 please advise about grapics, how to do and which driver will use. please advice and i thanks.

Feb 18, 2009 | Matrox G450 Millenium 32MB DDR PCI Dual...

2 Answers

Who is the mother board manufature for sy -p41 845pe? what type of cpu does sy -p41 845pe suport and speed range? the type of module, max support capacity and speed ranges? the type of chipsets? the type...


Processors
  • Supports all Socket 478 CPUs (400FSB & 533FSB)
Chipset
  • North bridge: Intel I845PE MCH
  • South bridge: Intel ICH4
System Memory
  • 3 x 184-pin DDR SDRAM
  • DDR200 / DDR266 / DDR333 support @ 2.5v
  • 3GB maximum system RAM
Slots
  • AGP slot, 4x AGP compliant (1.5v support only)
  • 6 x 32-bit PCI 33MHz slots
On-board peripherals - I/O
  • 1 floppy port supports 2 FDD
  • 3 Audio Jacks for the CMI9738 sound chipset
  • CMI9738 6-channel sound
  • Davicom 10/100 LAN (10/100 Mbit/s)
  • 2 USB2.0 ports and a further 4 available via headers
  • PS/2 ports
On-board IDE
  • An IDE controller on the ICH4 chipset provides IDE HDD/CD-ROM with PIO, Bus Master and Ultra DMA/100/66/ operation modes
  • Highpoint HPT371 RAID single-channel ATA133 RAID controller
  • Ultra DMA/ATA133, 100, 66, 33 operation modes
  • Supports up to 2 hard drives
  • Serial ATA support via the Marvell 88I8030 single-ATA bridge
  • Supports 1 S-ATA drive
BIOS & Voltages
  • FSB speeds of 100Mhz - 255Mhz (quad-pumped)
  • 1.1 - 1.85v Vcore adjustable in 0.025v increments
  • 2.5v - 2.8v Vmem adjustable in 0.1v increments
  • 1.5v - 1.8v VAGP adjustment
  • Fix AGP/PCI speeds and variable settings

Jan 22, 2009 | Soyo SY-P4I 845PE Motherboard

1 Answer

Ram upgrade


Your system support only 2Gb, only 1Gb at one bank. Please Checkout http://www.memoryx.net/aspire53151.html

you can even have your system Scan "Scan My System" from this site to give you an accurate system details.

Hope this fix your problem!

Dec 03, 2008 | Acer Aspire 5315 Notebook

1 Answer

Only boot in safe mode with Vista


Recheck that you have the exact driver for that ati card including the correct driver for the operating system you are using. physically pull the card and confirm the model of ati card you have.
also consider installing just the driver and not the catylist program.

Robert

Sep 01, 2008 | ATI RADEON 9600SE128MB AGP Video Card...

2 Answers

VIA CPU to AGP Problem with 3Gb and Vista


Problem is you need to install Vista which support 4Gb! Look for specification on Vista you have!! Mostly XP and Vista support 2Gb!
The problem is in your OS. 32 OS support max 2Gb of ram they detect you 3gb but they couldn't operate with all!!

Jan 25, 2008 | MSI KT4V (MS-6712) Motherboard

Not finding what you are looking for?
Abit IP35P Motherboard Logo

249 people viewed this question

Ask a Question

Usually answered in minutes!

Top Abit Computers & Internet Experts

Matthew Spark
Matthew Spark

Level 3 Expert

1066 Answers

David
David

Level 3 Expert

778 Answers

Jerry Umali

Level 3 Expert

979 Answers

Are you an Abit Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...