Question about Lexmark Document Distributor Advanced Edition Full Version for PC

Open Question

Exploded view of a distributor for a1929 ford model A

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Garden tractor. A.Y.P American yard pro


Request the exploded view from the manufacturer/distributor.

May 12, 2017 | Husqvarna Garden

1 Answer

How do l get a distributor diagram for a 1988 Ford ranger 2.3


Are you wanting the wiring diagram or distributor exploded view, all the above?
Autozone.com
Has free auto repair info and wiring diagrams.

Mar 03, 2016 | Ford Ranger Cars & Trucks

1 Answer

How do I find a drawing/ exploded view of the front driveline/u-joints/cv joints on a 2003 ford ranger 4x4?


google " drawing/ exploded view of the front driveline/u-joints/cv joints on a 2003 ford ranger 4x4", several sites come up including a video on how to change them out

Dec 11, 2014 | Ford Cars & Trucks

1 Answer

Where is the fuel pump on a 1965 ford mustang 289


Exterior tank side...

zjlimited_687.gif

Fig. 1: Exploded view of the mechanical fuel pump on most V8 engines

zjlimited_1796.jpg

Fig. Exploded view of the pump mounting (click image for zoom)

Hope helps.


Sep 06, 2011 | Ford Mustang Cars & Trucks

1 Answer

Where is the location of the egr valve on a standard 4x4 93 ford ranger?


62a387d.jpg

Fig. 3: Exploded view of the EGR system and related components for the 3.0L engine



e302e23.jpg

Fig. 4: Exploded view of the EGR system and related components for the 4.0L engine

Hope helps (remember rated and comment this).

Sep 12, 2010 | Ford Ranger Cars & Trucks

2 Answers

How do I change the distributor


REMOVAL NOTE: Once the distributor is removed, the engine should NOT be turned or moved out of position. Should this occur, please refer to the engine rotated installation procedure. Distributor components — 4A-F engine 88272p61.jpg
Fig. 1: Exploded view of the distributor — 4A-F engine 88272g41.gif
Fig. 2: Exploded view of the distributor — 1993 4A-FE and 7A-FE engines 88272g42.gif
Fig. 3: Exploded view of the distributor — 1996–97 4A-FE and 7A-FE engines 88272g43.gif
Fig. 4: Exploded view of the distributor — 4A-GF engine 88272g44.gif
  1. Disconnect the negative battery cable.
  2. Disconnect the distributor wire(s) at its harness. Loosen the screws holding the cap onto the housing 88272p05.jpg
    Pull the cap and wires off the distributor housing 88272p06.jpg

  3. On the 4A-F engines, disconnect the vacuum advance hoses. NOTE: On some models the distributor wires are part of the cap and can not be separated.
  4. Remove the distributor cap. Label and disconnect the wires from the cap. On some engines it will be necessary to use a flat bladed tool to lift up the lock claw and disconnect the holder from the cap. Fig. 5: On some engines, use a flat bladed tool to lift up the lock claw to disconnect the holder from the distributor cap 88272g45.gif

  5. Carefully note the position of the distributor rotor relative to the distributor housing (also note position of distributor to the engine assembly); a mark made on the casing/housing will be necessary for reassembly. Use a marker or tape so the mark doesn't rub off during handling of the case/housing. Mark the position of the rotor relative to the distributor housing 88272p07.jpg
    Label and remove all vacuum hoses attached to the advance on the distributor if equipped 88272p14.jpg
    If necessary, remove the rotor 88272p08.jpg

  6. Remove the distributor hold-down bolts. Remove the distributor hold-down bolts before pulling the unit from the engine 88272p13.jpg

  7. Carefully pull the distributor from the engine assembly. Remove the O-ring from the distributor shaft. Pull the distributor straight out from the engine 88272p15.jpg
prev.gif next.gif

Aug 13, 2010 | 1996 Toyota Corolla

2 Answers

How to replace oil pump


REMOVAL & INSTALLATION

Gasoline Engines
See Figures 1 and 2


7ec529c.jpg
Fig. Fig. 1: Exploded view of the oil pump used on 2.0L and 2.3L gasoline engines


20995b0.jpg
Fig. Fig. 2: Exploded view of the oil pump used on the 4.0L engine-2.8L and 2.9L engines are similar
  1. Follow the service procedures under Oil Pan Removal and remove the oil pan assembly.
  2. Remove the oil pump retainer bolts and remove the oil pump.

To install:
  1. Prime the oil pump with clean engine oil by filling either the inlet or outlet port with clean engine oil.
  2. Rotate the pump shaft to distribute the oil within the pump body. Install the pump and tighten the mounting bolts to 14-21 ft. lbs. on 2.0L and 2.3L engines; 6-10 ft. lbs. on 2.8L and 2.9L engines or 13-15 ft. lbs. on 4.0L engines.

Do not force the oil pump if it does not seat readily. The oil pump driveshaft may be misaligned with the distributor shaft assembly. To align, rotate the intermediate driveshaft into a new position.
  1. Install the oil pan as previously described. The oil pumps are not serviceable. If defective, they must be replaced.

Remember rated this.

Aug 11, 2010 | 1989 Ford Ranger

1 Answer

Exploded view diagrams


The diagrams are normal page size, nothing that big was ever printed by Ford

Jun 16, 2008 | 1965 Ford Mustang

Not finding what you are looking for?
Lexmark Document Distributor Advanced Edition Full Version for PC  Logo

Related Topics:

1,187 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lexmark Computers & Internet Experts

mukhtar21 shaikh
mukhtar21 shaikh

Level 3 Expert

2017 Answers

micky dee

Level 3 Expert

2775 Answers

Owen Barnes

Level 3 Expert

867 Answers

Are you a Lexmark Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...