Question about Maytag 24 in. MDB5651A Built-in Dishwasher

3 Answers

All the lights are flashing on Maytag Quiet Series 300

For some reason all the lights are flashing on the dishwasher display and counting down. It happened once before and I was able to press the start button and hold it in and it cleared it, but that didn't work this time. It just keeps counting down over and over and I can't start it now.

Posted by on

  • 2 more comments 
  • Elphaba Nov 13, 2007

    Flashing L on dishwasher and nothing is working when I press the buttons.....

  • foligno548 Oct 10, 2008

    Can someone resolve this issue - all the display lights blink in a pattern and it counts down from 50. I checked the two door switches (good) and reseated the connectors. The have the quiet series 300 but the model number is different. MDBH970AWQ

  • debsuetwo Jan 06, 2009

    i've tried all these suggestions and nothing is working. The "L" flashes on when I try to press any buttons (including Cancel) and holding down the Cancel for any length of time does not work. There is no "heated" wash cycle--just Heavy, Light, etc. cycles.

  • Anonymous Mar 22, 2014

    Lights blinking

×

Ad

3 Answers

  • Level 1:

    An expert who has achieved level 1.

    Governor:

    An expert whose answer got voted for 20 times.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 18 Answers

Try pressing heated wash, heated dry, then heated wash, heated dry. It should reset it. Also try pressing and holding the cancel button for 5 seconds to see if that works if the other doesnt.

Posted on Nov 18, 2007

  • pahl19 Mar 08, 2011

    I just pressed the heated dry button and held it down for 3 seconds. That seemed to reset everything and it works fine now.

  • Wanda Oct 17, 2012

    THat worked wonderfully!! I got a little worried cause it was completly full of dishes.

×

Ad
  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Tried the heated wash/heated dry sequence but no luck. Turned of power to dishwasher (300 series) for 5 secs and then turned power on and lights/count down stopped flashing/counting. This is the same procedure one does when your satelliite receiver hangs up.

Posted on May 07, 2010

Ad
  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I have a quietseries 400 I get a flashing L whe I press any button

Posted on Dec 21, 2008

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

  • 2 Answers

SOURCE: Maytag 300 Litghts flash in sequence

Yes I think I was able to solve the problem. I'm not sure, but it appears to be working properly now. Since I was able to possibly solve the problem, if you want the answer, I would like to direct you to my Premium Assistance Plan. For $9.99 I will give you the answer, just like you offered me.

Posted on Sep 20, 2008

  • 2 Answers

SOURCE: 1.5 year old Maytag Legacy Series Quiet Series 300 Lock Light on

Hold down the heated-dry button for 3 seconds and the light will clear.

Posted on Dec 19, 2009

  • 1 Answer

SOURCE: Maytag Quiet Series 300 Dishwasher will not turn off after it com

MY DISHWASHER KEEPS RUNNING, IT IS A WHIRLPOOL GOLD QUIET PARTNER IV

Posted on Apr 06, 2009

  • 1 Answer

SOURCE: Maytag Quiet Series 300 owners manual

my dishwasher does not want to work anymore it has a big L flashing

Posted on Sep 28, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

We have a whirlpool ADG 7800 dishwasher ,getting a beeping sound and start button flashes 12 times? Any help


Hi
.
Ok try this and see what happens.
.
Hold the start button again till it beeps
Then select the first cycle on the left which should be the rinse cycle
Then turn the dishwasher off
Then press and hold the start button and with this held in turn the dishwasher on.
Once the start light is flashing let go
Now press the start button once and close the door.
.
Now it will run a 12 minute test cycle. If it goes wrong it will drain the water out and beep. So open the door and count the number of flashes from the start light inbetween the pause and let me know.
.
Regards

Oct 11, 2014 | Whirlpool Dishwashers

1 Answer

Zanussi dishwasher beeps once and end of cycle light flashes


Most likely your dishwasher finds fault.

Appliances without a display will show the alarms by a number of flashes of the LED "end of cycle".

For example: one flash = i10, two flashes = i20
..........and so on

So, count how many times LED "end of cycle" flashes and you will know the error code.

Dado

Aug 24, 2014 | Zanussi Dishwashers

1 Answer

Electrolux (dishlex) DX302SJ dishwasher all lights flashing. When I press program and start buttons together code 1C flashes.


Take the kick panel off the bottom. There is a tech sheet in an envelope under the machine. IT will have everything that you need to do to troubleshoot the machine.

Dec 02, 2013 | Electrolux Dishwashers

1 Answer

I have filled dishwasher selected temperature and the start light is flashing but nothing happens I think the m/c type is 7197


The Start/Resume light is flashing

This flashing light indicates that your cycle or start-up was interrupted.
Possible causes: The door opened during the cycle, or the power was interrupted.
To resume operation: Make sure the door is closed, and press Start/Resume.

The Clean light is flashing

You should call for service if the Clean light is flashing and the machine is inoperable. It is normal if the Clean light stays on after the cycle is complete. The Clean light is an indication that the dishwasher has been run and that the dishes inside it are clean. Once the door is opened after the cycle is complete, the light will shut off.

The lights are rapidly flashing

Any key that gets stuck will rapidly flash. Press the key a few times in order to release it or press Cancel.

The Rinse Only light is rapidly flashing

If multiple keys are stuck, the Rinse Only light will flash. Press each key, one at a time, to release the stuck keys, or press cancel.

Jun 28, 2011 | Dishwashers

1 Answer

Unable to clean


Hi you can try
This works with most Brother printers

Procedure how to reset the error 46 error (unable to clean). This can be done on every Brother inkjet machine with a numeric keypad.

- Machine off
- Switch on the machine while holding down the “menu” button until all the leds are flashing on/off. Now you are in “maintenance” mode.
- press 80
- press the “mono start” button several times until you see “purge: xxxx”
- press “2783” in order to reset the purge counter. You will see: “purge:0000”
- press “99” to exit the maintenance mode

Now you are able to print again, but actually your ink absorber box is now full with ink. Ink flooding can happen if you don’t replace this ink box


Also can try.

Reset code.
Press menu then*2864 within 2 seconds (maint should be on the display and all the lights should be flashing, if not try again) press 80
then keep pressing black/mono start button until screen displays ‘purge count’
press 2783 to reset purge count
press stop/exit key
press 99
machine should return to normal



Mar 30, 2010 | Brother MFC-5840CN All-In-One InkJet...

1 Answer

Electrolux dishwasher delays before starting


  1. To cancel the delay.press the delay pad again when the delay is counting down. The indicator light will go out and the cycle will start or resume immediately.
  2. To cancel the delay and the cycle, press Start/cancel once to drain and turn-off the dishwasher.
  3. Press Start/cancel twice to turn-off the dishwasher without draining.

Aug 31, 2009 | Electrolux EDW5505ESS Built-in Dishwasher

1 Answer

Lights flash Intermitten and tiemr counts backwards


hi there,

it's either the touchpad or the control board that's malfuctioning. have you checked those yet?

Sep 18, 2008 | KitchenAid 24 in. KUDI02IRBS Stainless...

1 Answer

I cant get my dishwasher to turn on, i press the normal cycle and the light flashes 4or5 times and nothing happens, i've unplugged it and tried all of the cycles nothing works


Count the exact number of flashes prior to the pause - this is the error code necessary to diagnose the problem. What is the model number also?

May 13, 2008 | KitchenAid 24 in. KUDI01TJ - Multiple...

5 Answers

Kenmore dishwasher Lock On light flashing


holding the button for four seconds will not do it, you have to hold it until the light stops blinking and
will go back to normal, normall takes more than four seconds to unlock the unit, this is something
the sears repair techs know becouse the are trained on all this things but, they will not share this things, becouse thats how they make money

Dec 29, 2007 | Dishwashers

Not finding what you are looking for?
Maytag 24 in. MDB5651A Built-in Dishwasher Logo

4,143 people viewed this question

Ask a Question

Usually answered in minutes!

Top Maytag Dishwashers Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Charles T Nevin
Charles T Nevin

Level 3 Expert

4070 Answers

Mike

Level 3 Expert

4348 Answers

Are you a Maytag Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...