Question about Miele Novotronic W1918A Front Load Washer

1 Answer

Need replacement part for front load machine

The washer around the door (the grey rubber piece) has a piece (chunk) missing and we need to find a replacement. Any thoughts/ideas? I have a Miele Novotronic W 1930 front load washing machine that is about 11 years old.

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 4 Answers

Contact Mieleusa at (800) 999-1360.


Posted on Aug 06, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Manual release on door lock of a bosch nexxt series 100 washer


Try pulling door up before out. My washer does this when the rubber around the door gets a piece of wet paper under it, or I have overloaded it and the rubber gets moved. Once open, run your fingers around the rubber seal to verify nothing under it and that it lays smooth.

Jan 03, 2013 | Bosch Nexxt 100 Series WFMC1001UC Front...

1 Answer

My grey rubber gasket around the tub has a 1" rip in it. This is located where you open the front load door and on the grey rubber gasket just inside. Is there a patch kit? Or do I have to replace...


I search on google and no such patch kit. I tried a bike inner tube repair kit and it seems to work, but my holes are less than 1". Check out my post. I have a gasket on the way just in case.

Jan 03, 2011 | Whirlpool Duet GHW9150P Front Load Washer

1 Answer

Need to replacedoor lock sensor on model aftb7000epo


THERE IS A TINY SPRING CLAMP THAT GOES AROUND THE GREY RUBBER BOOT AT THE DOOR OPENING. THE BEST WAY TO REMOVE THIS IS AT THE BOTTOM 6 O'CLOCK POSITION. THEN UNATTACH RUBBER BOOT FROM DOOR OPENING.

Apr 22, 2010 | Frigidaire ATF6000ES Front Load Washer

1 Answer

Water is leaking from the bottom of my washer, it is maytag neptune ,front loading washer


Check the door boot (typically grey rubber bellows looking ring around the door opening that keeps the water in the tub from leaking) for cuts.

See the manual:www.applianceblog.com/manuals/MaytagNeptunenew.pdf
Joe

Jun 06, 2009 | Maytag Neptune MAH6500A Front Load Washer

1 Answer

The door leaks on my whirlpool front load model wfw8300sw03, looks like the door isnt sealing tightly, if I push on the door it stops lealing, any ideas?


you might have a bent door hinge, but most likely you have a worn door boot. its the grey rubber thing that the glass seals to.
try to lift up on the door to get the hinges back into place and if that doesnt work then you might need to replace the door boot.
look at the edge of the boot where the glass hits it. the glass must seal to the rubber and if the rubber is worn or torn then it wont seal.
not an easy piece to replace but it can be done. i wouldnt recommend trying it first as you will find it very tight to get your hands into and the clamps are hard to figure out as well.

Feb 03, 2009 | Whirlpool Duet GHW9150P Front Load Washer

1 Answer

Kenmore Elite Front load washer leaking


You need to replace the rubber gasket around the door.

Dec 16, 2008 | Kenmore Elite 45986 Front Load Washer

1 Answer

Rubber piece


If you mean in the bottom of the gasket between the drum and the door the hole is to allow water to drain from the gasket to prevent standing water which will smell .

Aug 08, 2008 | Malber P25 Front Load Washer

2 Answers

Mold on rubber around door


Yes he can change it himself just make a note of how it comes off and then reverse the process when refitting, the black is caued by damp and residue detergent, try doing a very hoy wash occasionally this will prevent this happening, it should also cure the stale smell that you get from the machine.

Sep 01, 2007 | Kenmore Elite 45986 Front Load Washer

Not finding what you are looking for?
Miele Novotronic W1918A Front Load Washer Logo

Related Topics:

343 people viewed this question

Ask a Question

Usually answered in minutes!

Top Miele Washing Machines Experts

Gerry Harvey
Gerry Harvey

Level 3 Expert

1474 Answers

mpservices

Level 2 Expert

128 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Are you a Miele Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...