Question about Life Fitness 9100 Next Generation Remanufactured Treadmill

5 Answers

9100 life fitness treadmill

Have a 9100 life fitness treadmill, runs for a few minutes then stops?

Posted by on

  • 2 more comments 
  • Anonymous Mar 23, 2014

    The treadmill runs fine for 30 minutes and then stops with an error. I recently replaced the blown fuse with a 15 amp fuse, but I am not sure if it should have been a 10 amp fuse instead.

  • Anonymous Mar 25, 2014

    turned on today and it has a motor comm error...where do we start with troubleshooting

  • Anonymous Mar 26, 2014

    my vision fitness stops after a few sec. wiyh error code E1

  • Anonymous Mar 31, 2014

    how to change kg to lbs on Life fitness tr 9100 elipticle

×

Ad

5 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Habit-Forming:

    Visited the website for 3 consecutive days.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 115 Answers

Sounds like you need a new lower board replacement. You can get that for that treadmill by call lifefitness or sportsmith.com Please rate me good

Posted on May 01, 2009

  • drdick8 Jan 19, 2014

    what's a "lower board"?

×

Ad
  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

This can also be due to excessive resistance on the motor which is caused by a worn belt and/or deck. Run the treadmill without getting on it and see if it still stops, if it doesn't stop without you on it then either there isn't enough current getting to the motor (this treadmill should be using a dedicated circuit) or the belt and/or deck need to be replaced. If it still stops then it could be the motor controller or the board in the motor compartment.

Posted on Dec 01, 2011

Ad
  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 4 Answers

It could be that your stop switch is not returning all the way. . With the machine off, tap the stop switch several times, then vacuum it to remove any loose debris. Put a little WD40 or other lubricant on a paper towel, then rub the paper towel on the edges of the switch. This should fix it.

Posted on Jan 22, 2010

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 2 Answers

Iv had similar problems, but it was when i had a lot of electricity being used at the house - every time i switched it on after a few mins it would go off.

iv read to dismantle the stop switch, clean and replace the microswitch. where can the microswitch be found from?

also, is the red stop switch that needs looking at?

also, which spring could do with replacing? as per post above?

Posted on Dec 01, 2009

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 5 Answers

You need to dismantle stop switch ,clean,replace micro switch and reassemble.replace spring if damaged or rusted also.

Posted on Jul 23, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Life fitness crosstrainer 9500 HR just shut down few second after start


see the video and fix it. This happen because the lack of maintenance schedule.God bless you

Apr 04, 2013 | Life Fitness Crosstrainer, 9100, 9500 Rear...

1 Answer

How do i refill the wax on my life fitness 9100 treadmill?


open cover on left at rear of treadmill, disconnect pipe, fill with wax kit and then reconnect pipe, 2 screws to remove wax cover.

Mar 30, 2013 | Life Fitness 9100 Next Generation...

1 Answer

Life fitness 9500hr?it wont start and says ....see maintance on display?any ideas


just bought a amazing model after reding review on this site thanks amazon rock http://www.pianoforall-review.com/life-fitness-treadmill-reviews-does-it-works/

Dec 03, 2012 | Life Fitness 9100 Next Generation...

1 Answer

I have A Life fitness 9100 treadmill The display shows the message "maintenance notes wax over" how can I remove this error?the treadmill will not turn on HELPPP


see this steps and fix it. .Of course you must read your instr. manual or download from www. iconservice.com
When the treadmill is not in use, press the "Stop," "ENTER" and "QUICK START" buttons in rapid succession. The "RESET" button can also be used, in place of the "Stop" button.

  • 2 Press the "ENTER" button three times to access the treadmill's error log.
  • 3 Press the up or down arrows to scroll through the error codes, if necessary for club or personal logging purposes.
  • 4 To view the treadmill's odometer reading when a particular error code was elicited, press "SELECT" while a particular error code is displayed.
  • 5 To clear the error log, press "QUICKSTART" for a minimum of four seconds while viewing the list. Prompts will appear on the display and let you know when the log has been deleted.
  • Oct 17, 2012 | Life Fitness Lifestride 9100 HRT...

    1 Answer

    What's your problem?I have a life fitness 9100 hr I have a problem how do I clear the message waxer tank empty?


    see this step and fix it. God bless you
    Unplug the treadmill. Locate the console key and place the safety or reset key into the treadmill console. Replace any parts that need replacing, or move on to the next step.

  • 2 Locate the reset switch on the underside of the treadmill console. Usually the button is large enough to trigger with a pencil eraser or Q-tip. Plug the treadmill plug back into the wall. Use the Q-tip to press the reset button. It may be necessary to hold the reset button down for a few seconds. "CL11" will appear in the display of the treadmill.
  • 3 Press the reset button one more time with the Q-tip. "CL21" should appear on the screen. Press the enter key. The display will change again and show "CL22." Keep pressing the enter key until the numbers cycle through to the number "CL26." Press enter one more time. The letter E should appear on the display screen.
  • 4 Press enter twice more. The letters "SS" should appear on the screen. When this happens, press the start/stop key. Making sure to keep well away from the tread, press enter to start the treadmill. The treadmill will start on its own. The treadmill will stop on its own after a few seconds. When it stops, press the power key two times. Remove the safety key and put in a safe place. Your treadmill is reset.
  • Oct 15, 2012 | Life Fitness 9100 Next Generation...

    1 Answer

    I have a life Fitness 9100 that do great walking but if I start running on it, it will automatically shut down to start menu. Is it the wax? or any suggestions?


    the stop switch is bad to check this out start the tread and press around the stop switch on the counsel and see if it shouts down

    Aug 18, 2010 | Life Fitness Exercise & Fitness

    1 Answer

    I can't reset a fault named "wax empty" and my equipment doesn't work life fitness 9100


    hit the stop button and hold down pouse key until the counsel repowers up and tougle throug to mantinace enter then tagel throug to waxer refill and hit enter

    Aug 13, 2010 | Life Fitness 9100 Next Generation...

    1 Answer

    Hi i have life fitness 9100 hr. it is not starting..after inter your weight..it shuts off


    Could be a number of reasons - first to check would be the small micro switch behind the red "stop" button. these sometimes go faulty and will reset the machine at data entry

    Mar 02, 2010 | Life Fitness 9100 Next Generation...

    4 Answers

    Lifefitness 9100hr treadmill cut out


    iv had similar problems, only happened once tho - i switched it on after a few mins it would go off.

    iv read to dismantle the stop switch, clean and replace the microswitch. where can the microswitch be found from?

    also, is the red stop switch that needs looking at? how can i remove it?

    i was wondering on how i can service/maintain this properly, can anyone advise my on how to give this a service.

    Jul 14, 2009 | Life Fitness 9100 Next Generation...

    Not finding what you are looking for?
    Life Fitness 9100 Next Generation Remanufactured Treadmill Logo

    1,019 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Life Fitness Exercise & Fitness Experts

    Howard
    Howard

    Level 2 Expert

    115 Answers

    Electro Med Services...
    Electro Med Services...

    Level 3 Expert

    6694 Answers

    Matt Olenzek
    Matt Olenzek

    Level 2 Expert

    297 Answers

    Are you a Life Fitness Exercise and Fitnes Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...