Question about Zanussi 18 in. ZDT5044 Built-in Dishwasher

Open Question

Zanussi ZDT 6244 Dishwasher

When I select a program I get three intermittent audible signals.

The possible cause according to the manual is Protection against flooding is active. Can you help

Posted by on

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 2 Answers

SOURCE: zanussi zdt 6252

I had the same problem with Zanussi ZDT 6252. To fix it, turn power on, close door fully, then open door, turn off then turn back on again. If you follow this sequence the machine is reset and you can select programs again.

Posted on Feb 15, 2009

Ad
  • 901 Answers

SOURCE: Zanussi ZDT 6244 Dishwasher , wash cycle completes

Try cleaning all the jet orifices in the rotating vanes. Use tooth brush. Check for dish plate is touching the rotating arm in the wash chamber. Rotate by hand for freeness.

Posted on Mar 30, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Zanussi zdt 6053 usually will not run full cycle (on any cycle) but stops with constant error beeps. But it is draining ok and sometimes goes full cycle (not often) Any ideas?


Could be anything!
If you suspect that there is a fault then it will be displayed by blinking LED "END OF CYCLE". As the display of failure in hexadecimal code it can flash up to max. 15 times than short pause and after that repeat fault code. You must to count the number of times the LED "END OF CYCLE" flash up.

Example from user manual: Anti-flood device is activated.
- continuous flashing of the indicator light of the running programme
- 3 intermittent audible signals
- 3 flashes of the END OF CYCLE indicator light
(which means "i30" fault code, the cycle is interrupted and the
drain pump switches on).
Possible causes:
Water leakage from the tub - sump and various connections
(pump, upper spray arm duct etc.); floating sensor blocked
mechanically; microswitch faulty; fill solenoid blocked
mechanically; circuit board faulty (solenoid triac short-circuited);
wiring faulty.
26226179-aipk5px1bmfkdpsmrgevaqwn-3-1.jpg Could be also:
To cancel a washing programme in progress:
- Open the dishwasher's door.
- Press the programme selection/cancel button for about 3 seconds,
until the indicator light of the running programme turns off and the
END OF CYCLE indicator light flashes, indicating that the running
programme has been cancelled and that the machine has
returned to setting mode. It is now possible to select another
washing programme. If a new washing programme will be
selected, check that there is detergent in the detergent dispenser.

NOTE: only during the drying phase, if the dishwasher's door will be opened and remains open for more then 30 seconds, the running programme will be automatically cancelled and the machine will return to setting mode. This will happen, always only during the drying phase, also when the machine is switched off by pressing the
On/Off button and remains switched off for more then 30 seconds.

Dado

Jun 26, 2016 | Zanussi Dishwashers

1 Answer

MY DISHWASHER WONT START ITS CYCLE THERE IS VIBRATION IN THE BOTTOM AND NO WATER ENTERING


The vibration is probably the electric valve that opens and closes the water supply valve on the dishwasher underside. If you have set a few dishwashers before, you may be able to remove yours to access the solenoid valve on the bottom of your dishwasher and replace this part for a few bucks, then reset the dishwasher and test. The buzz/no water symptom points directly to this part being your problem. DO NOT work on your dishwasher without some previous knowledge of dishwashers in general. The electrical power must be shut off/unplugged, the water supply must be shut off and the drain hose must be disconnected before removal and repair. Be careful and good luck.

Feb 17, 2015 | Zanussi Dishwashers

1 Answer

Can I turn the beeper off on the end of the washcycle on the DDY062 Hoover dishwasher. I want to put it on timer delay and dont want to be woken in the middle of the night.


These are the instructions taken directly from the DDY062 manual:
Alarm mute for the PROGRAMME END
The alarm for the programme end may be muted as follows:
IMPORTANT The dishwasher must be ALWAYS off before start this procedure.
1. Hold down the "PROGRAMME SELECTION" button and at the same time switch on the dishwasher by pressing the "ON/OFF" button (a brief audible signal will sound).
2. Keep the "PROGRAMME SELECTION" button pressed for at least 15 seconds (during this time, 2 audible signals will sound).
3. Release the button when the second audible signal sounds (3 "PROGRAMME SELECTION" indicator lights will come on).
4. Press the same button again: the 3 indicator lights (which indicate that the alarm is activated) will start flashing (to indicate that the alarm is off).
5. Turn off the dishwasher by pressing the "ON/OFF" button to confirm the new setting.
To turn the alarm on again, follow the same procedure.

Jun 21, 2012 | Hoover Dishwashers

1 Answer

Zanussi ZDT 6252 dishwasher will not work


Almost certainly the control board has gone faulty. The favorite is the transformer burns or the thyristor gets very hot and burns due to a bad solder joint. Quickest no noncense repair is to bite the bullet and install a new board.

Jun 05, 2010 | Zanussi 23 in. ZDT6252 Built-in Dishwasher

1 Answer

Zanussi ZDT 6244 Dishwasher , wash cycle completes , all water drains out , but the dishes are not brilliant clean & dishes are still wet


Try cleaning all the jet orifices in the rotating vanes. Use tooth brush. Check for dish plate is touching the rotating arm in the wash chamber. Rotate by hand for freeness.

Mar 29, 2010 | Zanussi 24 in. DE6544 Built-in Dishwasher

1 Answer

Just moved in and run the dishwasher


Replace the timer.

Most likely it was broken by someone resetting the timer by hand while the unit was energized.

Always open the door(de-energizes the timer) when you want to make an adjustment to the machine while it's running.

Jun 21, 2009 | Zanussi 23 in. ZDT6252 Built-in Dishwasher

1 Answer

Changing heating element.


You normally access the element from the side , Be careful of sharp edges . meter it before you start spending money it could be a timer fault also !

Maurice

Feb 15, 2009 | Zanussi 23 in. ZDT6252 Built-in Dishwasher

1 Answer

Zanussi zdt 6252


I had the same problem with Zanussi ZDT 6252. To fix it, turn power on, close door fully, then open door, turn off then turn back on again. If you follow this sequence the machine is reset and you can select programs again.

Dec 26, 2007 | Zanussi 23 in. ZDT6252 Built-in Dishwasher

Not finding what you are looking for?
Zanussi 18 in. ZDT5044 Built-in Dishwasher Logo

Related Topics:

341 people viewed this question

Ask a Question

Usually answered in minutes!

Top Zanussi Dishwashers Experts

paulcarew

Level 3 Expert

2518 Answers

Owen Barnes

Level 3 Expert

867 Answers

Gerard Curran

Level 2 Expert

114 Answers

Are you a Zanussi Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...