Question about StarTech.com StarView SV431USB 4-port KVM Switch

1 Answer

The box super us starview 4

How do u enter the codes in 2 my box what setup is it u have 2 go through

Posted by on

  • loftys0504 May 11, 2010

    again more details needed sorry

×

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 8 Answers

To enter the codes
1 - Press menu
2 - Press 1570
3 - Make sure key emu is on
4 - Enter nagravision
5 - Make sure it says ntl at the top box, if not press right till it says ntl
6 - Key number should be on 00
7 - Go to key data and put this code in *******************(what u have)
8 - Go to key number and press right so its on 01
9 - Press down so you are on key data and enter this code ******************(what u have)
10 - Press ok to save
11 - All done

Posted on May 07, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need a universal remote code


Try 0000..
If that doesnt work I have another solution for. Westinghouse flat panel TV
TV 10812 probably has the correct IRsignalsfor enter programmed to the ok/select button. However the comcast and access remotes are intended to control a cable system so even in tv mode the remote sends the digit, ch+1and enter signals to the set top box.
There are two ways to defeat this.
1)Turn off channel lock. Sethe 9xx comand for this.
OR2) Assign a EFC for the Enter signal to the device mode.
1) Press TV
2) PRESS SETUP UNTIL IT BLINKS TWICE.
3) Enter 994 (two blinks)
4) Tap setup(DO NOT HOLD)
5) Enter 00069
6) Press ok/select.
The remote should blink twice and the ok/select button should work in the tv mode.
Use 1 unlessyou're going to use remote with cable box.
I hope this works...

Dec 17, 2014 | Westinghouse Televison & Video

1 Answer

Hi, recently I have lost my controller to my alba freeview box I was hope on of you guys had a little more experience than me in connecting another controller to the box.if you could get back to me on


If you wish to buy a genuine remote control, you have to contact the authorized service center. If you wish to buy a universal remote control, you should know about, which brand remote control have set-up codes to your TV brand, and buy that one according to availability. The first thing you have to do is, to confirm the number of digits in the setup codes to your TV brand. There are 4 digit, 5 digit, 3 digit and even 2 digit codes. You can make it sure by entering '0s' at the code enter window the TV dispays, and asks codes. Enter 'Zeros', and count how many zeros can be enterd. That number will be the number of digit of setup code, the TV/Device need. If you can enter 5 zeros, the number of digit in the set-up code to your TV is a '5' digit one, if only 2 zeros can be enterd, the number of digits in the set-up code to your TV should be a 2 digit one, and so on.. If you wish to get more details about this, try the sites linked here.
http://electrohelponline.blogspot.com/
http://electro-medical.blogspot.com/
Both the sites have setup code list, and setup procedure to many popular brand remote controls. Check the site in 'Mosaic' view. It will make search easy.

Jan 18, 2014 | Televison & Video

1 Answer

Need codes for emerson & also insructions to program comcast remote


Hello
Setup codes for Emerson TV with "Comcast On demand Custom-3 Universal remote control are:

0154, 0236, 0463, 0180, 0282,
0178, 0179, 0038, 0177, 0280

The Comcast Custom 3-Device universal

remote control is preprogrammed at

the factory to operate the Cable Box

supplied by your Comcast system, an

RCA TV, and an RCA VCR (in the AUX

mode). To control devices other than

default brands (excluding the Cable

Box), perform the below steps; otherwise
skip this section:

1* Turn on a device (e.g., VCR or DVD

Player) and, if applicable, insert

media, (e.g., video cassette or disc).

NOTE: Please read steps 2 to 6 completely

before proceeding. Highlight or write

down the codes and device you wish to
program before moving on to step 2.

2* On the remote control, press a

device key once (i.e., AUX or TV).

NOTE: Use the AUX key to program

control of an Audio Amplifier or

Receiver, a DVD Player, a Home-

Theater-In-A-Box Device, a PVR (or
DVR), or a VCR.

3* Press and hold Setup until the

selected mode key blinks twice,
then release Setup.

4* Locate the code for your device in

Manufacturer's Codes on the back

of this user guide. Brands are listed

in alphabetical order with the
most popular codes listed first.

5* Enter the first four-digit code for

your device. If you perform this

procedure correctly, the selected

mode key will blink twice.

NOTE: If you enter an invalid code, the

selected mode key will display one long

blink and exit the programming mode.
Repeat steps 2 to 5 with a valid code.

6* Aim the remote control at your

device and press Power once. The

device should turn off. If it does

not respond, repeat steps 2 to 6,

trying each code listed for your
brand until you find one that

Searching For Your Code.

NOTE: If the device does not have a
Power key, press the (Play) key
OK

Aug 22, 2011 | Televison & Video

2 Answers

What are the comcast remote codes for Sony HT-SS370 home theater system?


If you have this comcast Universal Remote - Red OK/Select Button here are the codes Sony 11100, 10000, 11317

if this doesn't work use the search mode

Searching For You our Code
If your home entertainment device does not respond to the remote control after trying all of the codes listed for your brand, or if your brand is not listed at all, try searching for your code.
For example, after trying all of the codes for your TV, you still cannot get the remote control to operate your TV, then:
1. Turn on your TV.
2. On the remote control, press TV once. Then press and hold Setup until the TVTV key blinks twice, then release Setup.
3. Enter 9 - 9 - 1. The TV key will blink twice.
4. Press and release the digit 1. The TV key will blink twice.
Note: Substitute 1 with 0 if searching for a Cable code, 2 if searching for a DVD, VCR or PVR and 3 if searching for an Audio device
5. Press Power and aim the remote control at the TV and press CH + one or more times until the TV turns off.
NOTE: In the search mode, the remote control will send IR codes from its library to the selected device, starting with the most popular code first.
6. Press Setup once to lock in the code.The TVTV key will blink twice.
7. To search for the codes of another device, repeat steps 1 to 5, but substitute the AUX key for the device you are searching for.
Checkcking the Codes
If you have set up the remote control using the Searching For Your Code
procedure, you may need to find out which five-digit code is operating your equipment. Perform the following steps after setting up your devices to find out which five-digit code operates your equipment. For example, to find out which code is operating your TV:
1. Turn on your TV.
2. On the remote control, press TV once. Then press and hold Setup until the TV key blinks twice, then release Setup.
3. Enter 9 - 9 - 0. The TV key will blink twice.
4. To view the code for the first digit, press 1 once. Wait 3 seconds and count the number of times the TV key blinks (e.g., 3 blinks =3) and write down the number in the left most TV Code box (at end of this section).
NOTE: If a code digit is "0", the selected mode key will not blink.
5. Repeat step 4 four more times for the remaining digits. Use 2 for the second digit, 3 for the third digit, 4 for the fourth digit and 5 for the fifth digit. Finish writing down the code in the TV Code boxes (at end of this section).

It can be a pain but once you get it down its a cake walk.

Jan 23, 2011 | RCA L42FHD37 42 in. LCD HDTV

2 Answers

Looking for remote codes for vizio sound bar and comcast remote


After much research, here is a step-by-step for getting your Vizio Soundbar to work with the Comcast remote using EFC codes (mine is the newer charcoal grey one, works great!)
Aux - Setup (2 blinks) - 11144 (2 blinks)Aux - Setup (2 blinks) - 994 - Setup - 00169 - Vol Up - Should get 2 blinksAux - Setup (2 blinks) - 994 - Setup - 00168 - Vol Down - Should get 2 blinksAux - Setup (2 blinks) - 994 - Setup - 00037 - Mute - Should get 2 blinksAux - Setup (2 blinks) - 994 - Setup - 00165 - Power - Should get 2 blinksAux - Setup (2 blinks) - 994 - Setup - 00164 - Input - Should get 2 blinks
These are optional, I didn't use them:Aux - Setup (2 blinks) - 994 - Setup - 00036 - <button to use for TVOL> - Should get 2 blinksAux - Setup (2 blinks) - 994 - Setup - 00101 - <button to use for TSHD> - Should get 2 blinks
Then set the volume control on the remote and other settings according to the Remote's manual.
ENJOY!! Hope this helps someone...

Aug 28, 2010 | Vizio High Definition Sound Bar

1 Answer

I need to manually program my universal vizio remote


Hi,

1. Manually turn on the VCR/DVD/Cable set top box.

2. Press the VCR/DVD/Cable set top box button on the remote control.

3. Press and hold the SETUP button until the LED LIGHT flashes twice.

4. Enter the codes using the Number Buttons. If the code is accepted, the LED flashes twice after the last digit is entered.

If the LED does not flash twice, repeat Steps 2 through 4 with the next code listed for the component and
manufacturer.

5. Point the remote control at the VCR and press the POWER button. The VCR/DVD/Cable set top box will turn off.
6.Your are done.

Thanx

Jul 23, 2010 | Vizio VR2 Remote Control

1 Answer

Entering new codes using remote control


hi go to afterdawn.com you will get all the help you need.hope this helps.

Dec 01, 2008 | StarTech.com StarView SV211K 2-port KVM...

1 Answer

Codes and how to set box


1stly.......press.............menu............then.............yellow button on ur remote..........it should pop up?? unless you got old box its bluebutton........then use ur remote to enter codes such as(letter A would be TV)it tells you at bottom of screen if your following these steps..........then 1st two boxes at top...............enter...............5A 01 if ur telewest.........then codes

key 00 = 98 B0 BA 52 D3 21 08 B4

KEY 01= D2 EA 29 B7 B5 52 E9 AD

then press................OK...............and then..............EXIT that should be you sorted always use remote to enter codes........recall..........info.............p+.............p-.....them buttons u should see at bottom screen??


hope helps?/

charlize

Nov 29, 2008 | StarTech.com StarView SV211K 2-port KVM...

3 Answers

CORRECT SETUP CODE FOR RECEIVER


Originally Posted by 3FingeredGlove viewpost.gif We can make this work. You didn't mention which setup code you're using, or explicitly say whether the OK/Select button is red or gray (the manual you're using is for gray), so these are somewhat generic instructions. Should work, though. This will provide a power toggle function to the Power key.

Use red numbers for the red OK/Select button remote, grey numbers for grey button remtoes.
Temporarily assign setup code 30842 or 0842 to AUX
1) Tap AUX
2) Press Setup until 2 blinks
3) Enter 30842 or 0842The remote should blink twice

Assign NEC1 IR protocol device 210, subdevice 108, function number 203 to Power (you don't need to understand these numbers)
1) Press Setup until 2 blinks
2) Enter 994 (2 blinks)
3) Tap Setup
4) Enter 00051
5) Tap Power (not All On)
The remote should blink twice

Assign setup code 30135 or 0135 to AUX (this is NEC1, 210.109)
1) Tap AUX
2) Press Setup until 2 blinks
3) Enter 30135 or 0135
The remote should blink twice

Nov 15, 2007 | Onkyo HT-SR800 System

1 Answer

RCA TV won't change channels


Your set uses the 195 series chassis and you have something set wrong in your guide plus. Go into the TV's menu and do a complete set-up. Take the remote and press MENU, then "8" to enter setup, then press "1" for "begin setup now" and then press "1" for English, and so on. You must enter "set up guide plus+", then press OK on the remote to choose "setup", select "USA", enter your zip code, and then if you choose "yes" for "do you have cable?" you MUST then choose "no" for "do you have a cable box" If you choose "yes" for that choice, your tuner will lock on one channel no matter what channel you try entering. After choosing "no" for "do you have a cable box", choose "no" for "do you have a VCR?", exit the guide plus menu and then skip the rest of the steps by pressing "2", and then exit the main menu by pressing "0". Your channels will then work normally.

Aug 29, 2007 | RCA P52937 52" Rear Projection Television

Not finding what you are looking for?
StarTech.com StarView SV431USB 4-port KVM Switch Logo

Related Topics:

206 people viewed this question

Ask a Question

Usually answered in minutes!

Top StarTech.com Computers & Internet Experts

Les Dickinson
Les Dickinson

Level 3 Expert

18424 Answers

Alun Cox

Level 3 Expert

2678 Answers

mbowen171
mbowen171

Level 2 Expert

15 Answers

Are you a StarTech.com Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...