Question about Zebra Z4Mplus Label Printer

2 Answers

Sent too many labels to printer - need to reset

I sent too many labels to my zebra z4m Plus printer. How can I clear memory? Tried: power off, power on and hold clear until data light stops flashing. labels started to print again.

Posted by on

  • 1 more comment 
  • jhart71 Apr 21, 2009

    The data was sent to the printer and the job is no longer visible. The data is spooled in the printer.

    Is there any way to clear that spooled data from memory?

  • jhart71 Apr 21, 2009

    Told user to unplug for 15 min. just to be safe. Labels are still printing... We're eating up label stock like crazy. Any other suggestions?

  • babadugo Nov 23, 2009

    When I tried to print to my Z4M plus Zebra printer it is wasting labels.

×

Ad

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 32 Answers

As the previous expert has stated, with the printer paused, press the cancel key to cancel the job. One thing to note, is depending on how your software sends the print jobs, you may say print 1000 labels, but the software sends it one at a time, so basically you have 1000 print jobs in the printer. If you pause the printer, press and hold the cancel key. Hold it for about 2 mins. This should clear the buffer.

Posted on Oct 27, 2009

Ad
  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 8 Answers

Your labels job need to be cancel from your computer. If your using windows, try this :you go in your start menu-Setting-Control Panel then check for printer and fax icon and double-click on it, then you'll see your printer's icon. Double-click on it, you should see your print job in the list. Right-click on it then cancel the job. Confirm your cancellation and it should set the problem.

Posted on Apr 21, 2009

  • 1 more comment 
  • Alain Charbonneau Apr 21, 2009

    Try to disconnect the lableler for at least 10 min. it should clear the spoole.

  • Alain Charbonneau Apr 21, 2009

    put it in pause mode. When done press cancel button and it should cancel the current job, if other job are in queu and want to delete them repete cancel as long as there still job in queu

  • Alain Charbonneau Apr 21, 2009

    could have many job in queu.

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I turn on the zebra z4m and it runs the labels even with no information sent to the printer. I can not use the cancel or pause button to stop. I runs for a minute and then error condition ribbon out. I...


1.Double check that the ribbon and the labels are routed correctly. 2.Make sure the media guide is holding the labels against the inside of the printer and not moving to the right away from the media sensor. If the labels are sliding to the right as they come out, increase the left side head pressure on top with a flat blade screw driver. Download the user manual at zebra.com .Check the media type and sensor type, and set for thermal transfer if using a ribbon.

Feb 24, 2011 | Zebra Z4M Printer

1 Answer

Why would bar code print both vertically and


This is I think due to the data being sent to your printer. On a Z4m the width is 4 inch and whatever is beyond is not printed. On your Z6M the coordinates are valid so your printer will print the code.

Mar 26, 2010 | Zebra Z6M Thermal Label Printer

2 Answers

Zebra Z4M Plus


Is the length of the label correct on the configuration print out?
Else try t check if there isn't a feed or print adjust in the parameters

Jun 25, 2009 | Zebra Z4M+ Printer

2 Answers

Zebra printer 140xilll - Too many print jobs?


It does sound like you have a memory overload when you send the 2nd print job. Each label is getting sent to the printer and filling up the memory. Make sure you are using the printer resident fonts and not a regular windows font. The windows fonts get sent down as graphics and take up memory. What zebra is saying to do is store the format of the label in the printer memory and then just send down the information that changes. For example if you were printing a UPS label the basic format of the label is the same but things such as the addresses and tracking # would change.

Jun 23, 2009 | Zebra 140XiIII Plus Thermal Label Printer

1 Answer

Zebra Z4M only feeds a small portion of the label.


You should try a factory reset. Power off the printer. Hold the "pause" and "feed" buttons down while powering up. Allthe lights will blink and when they stop blinking, release the "pause" and "feed" buttons. This will factory reset the printer.

Apr 24, 2009 | Zebra Z4M Printer

2 Answers

(zebra Z4M PLUS)


Here is a website to help with specs and supplies...

CLICK HERE

Nov 27, 2008 | Zebra Z4Mplus Label Printer

1 Answer

ZEBRA Z4M LABEL PRINTER LOCKED UP


The printer is Z4M or Z4M plus? I found this error at z4m plus and the solution is to change the motherboard. Roberto Martinez Mexico bartech9@yahoo.com.mx

Nov 14, 2008 | Zebra Z4M Printer

3 Answers

ZEBRA Z4M PRINT QUE ERROR


Try a reset: press the PAUSE and FEED keys while turning the printer, release the keys when feed the label. You can also try downloading the latest firmware.

Jul 02, 2008 | Zebra Z4M Printer

1 Answer

Zebra Z4M Plus


this is a color printer or not

Oct 01, 2007 | Zebra Z6M Plus Thermal Label Printer

Not finding what you are looking for?
Zebra Z4Mplus Label Printer Logo

2,614 people viewed this question

Ask a Question

Usually answered in minutes!

Top Zebra Office Equipment & Supplies Experts

pkwc

Level 2 Expert

254 Answers

Dave Busselle

Level 1 Expert

54 Answers

CheckitRight
CheckitRight

Level 3 Expert

1362 Answers

Are you a Zebra Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...