Question about Dishwashers

1 Answer



Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert whose answer gotĀ voted for 20 times.


    An expert who has answered 20 questions.

  • Expert
  • 116 Answers

Open the door panel and look for the screws holding it together. it is in the panel and may not look like a fuse if its a thermostaic fuse. it will look like a silver resistor. ohm check it and see if its closed.

Posted on Apr 21, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Rangemaster fault finding

It is possible the drain hose at the back of dishwasher is kinked or you have lifted it up too high under the kitchen sink.

Assuming you have the buzzer also beeping at the same time. See page 14 on this manual. Not sure if this is your dishwasher model number.

Apr 01, 2014 | Dishwashers

1 Answer

Dishwasher fault finding

you water level in your dishwasher is probably low if you change your water valve and run a dishwasher cleaner through it that will solve your issue

Dec 30, 2013 | Beko Dishwashers

2 Answers

Samsung dishwasher no power/display off

The Samsung DMR57LFS Dishwasher has a 15 Amp/250VP Volt Fuse located on the lower right side of dishwasher behind an aluminum panel held by two screws. Pull dishwasher out from counter, remove lower rectangular aluminum panel, and it is just inside underneath. Unscrew fuse holder and replace fuse. I had to pay a Samsung Authorized Repairman $109.70 to replace a simple fuse. I learned the hard & expensive way. Samsung won't tell you to check the fuse underneath the unit. They won't even tell you that there is a fuse underneath on the right side. The fuse protects the Printed Circuit Board or Blue LED Control Panel in the event of a power surge or lightning strike.The less than $4.00 fuse will blow first.

Jan 27, 2013 | Samsung DMR57LFS Stainless Steel Builtin...

1 Answer

The LED's don't come on. Why?

Is it that the LED's don't come on or is it that the dishwasher does not work? i.e. if you push the buttons you need to run it and close the door does it run. I would wager that you have blown the breaker for the circuit for the dishwashers. These appliances can draw alot of current and should be on a circuit by themselves.

If the breaker is blown you should see this by finding your breaker box and locating the switch for the dishwasher, it will be popped out of the on position. Switch it to off and then back to on. If you are in an older place it will be fuses and not breakers and you will need to replace the fuse.

Oct 25, 2012 | Dishwashers

1 Answer

KUDS01FLWH6 clean light flashing, replaced fuse kit and wire harness but still won't run after reset

Hi David, welcome to FixYa for starters.

Sorry to hear about your difficulty in finding a remedy for your dishwasher problem, but I believe I have a fairly simple solution to a very common problem, specifically with these machines (provided the model number is indeed KUDS01FLWH6 as indicated).

I'll direct you to my blog site as opposed to writing the complete solution out here,

if you cannot link up to it for any reason, please let me know. good luck and thank you for choosing FixYa.


Macmarkus :)

Nov 07, 2011 | KitchenAid 24 in. KUDS01FLSS Built-In...

1 Answer

Dishwasher will not work. heated dry and child lock lights are lit up. tried holding heated dry button for 3 seconds to turn off child lock nothing happens.

Try finding the electrical circuit that powers your dishwasher. Turn off the breaker for a while (15-30 min.) This may reset the computer to factory defaults.

Apr 29, 2011 | Haier ESD310 24 in. Dishwasher

1 Answer

I have a whirlpool quiet wash dishwasher model no. DUG12PF6B2

The fuse is a white square shaped fuse located on the bracket that holds the control board in place, with two wires going to it. When you replace the fuse get the kit that has wire extensions with it. Extend the wires as the kit suggest. It will save you from replacing the fuse again. Current is what took the fuse out.

Sep 09, 2009 | Dishwashers

1 Answer

Dishwasher not draining

the first things to look for, are the simplist faults.
1:) Check that the Outlet Hose-Pipe Isn,t Blocked-Kinked Or Bent.
2:) Check that the Pump, is not clogged/Blocked or not-functioning.

Hope this helps you start, your fault-finding successfully.

Mike @ Compurepair.

Aug 02, 2008 | Maytag 24 in. MDB5600A Jetclean II...

1 Answer

Shu43 built in dishwasher

Running the hot water in the sink until you get the water hot then, make shore you are using jet dry. Bosh dishwasher dry with condensation. Let me know

Aug 02, 2008 | Bosch 24 in. SHU43 Built-in Dishwasher

1 Answer


grazi, your part number for the use and care manual is LIT3368766. You may have to call Whirlpool, thats who made this dishwasher and inquire with them. Im not finding it on any parts suppliers...Catriver.

Feb 03, 2007 | Kenmore 24 in. 16304 Built-in Dishwasher

Not finding what you are looking for?
Dishwashers Logo

Related Topics:

527 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dishwashers Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers


Level 3 Expert

76846 Answers

Brad Brown

Level 3 Expert

16194 Answers

Are you a Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides