Question about Intel DG965WH Motherboard

2 Answers

Boot packard bell 181379 phenoix bios 4.04 wont boot past post error is 3f8h address conflict wont find any drive cant use system disk (wont find A:)cant get to cmos setup

Posted by on

  • ttttwwww Sep 21, 2007

    thanks I will try this if I want to flash bios
    but for now removeing the battery for a time did the trick. P.S. This board did not seem to like the removal of the coin battery. is this a way of telling me i should have tried the bios re-write instead?????


    Thanks

  • desolve Dec 07, 2007

    Need A User Manual To provide jumper settings and proper toggle settings on the main board. So I can run throu system bios. To cofigure my motherboard to install an O/S system.Wish I could get a manual. Thank You!!!!!!

×

Ad

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 165 Answers

3F8 is a comm port address, try removing modem card if you have one. Once you can get into bios setup, disable comm port that is using 3f8.

Posted on May 10, 2008

Ad
  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 293 Answers

CORRUPTED BIOS Reprogramming the BIOS That depends on your motherboard Model. It should correspond to your BIOS Model. Download the Motherboard's BIOS file usually in a Zip file then the contents are .bin files. Then use the BIOS manufacturer's EPROM Programming tool. Which usually comes with a user manual or guide on how to's. Just follow its examples. Hope this helps ======================= If you are having trouble with Newly bought items save your self from headaches by returning them and demand a replacement or a refund! You may have purchased a reconditioned\repaired\factory defect product.

Posted on Sep 21, 2007

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hello, I have a Packard Bell branded laptop displaying the error there is no boot disk see details and the photos in first comment to know what happens and did someone can help me with it?!


If you set the boot order to USB first boot device and HD second. Insert USB and boot from there. It should find your HD and then you can install your OS. Another system for a different laptop will not work!

Jun 15, 2016 | Packard Bell Computers & Internet

1 Answer

Cannot get passed bios screen


Eighter the disk drive is devective or the Boot sector is corrupted.
You have tried Stating with the Windows Installation Disk and chose repair ?

May 09, 2014 | Packard Bell Computers & Internet

1 Answer

Imedia system32 error


okay this is a confusing post/question. you can always start a machine from bio regardless of what operating system you're running. if you're attempting to boot from the disc, tap f12 @ boot until you get a one time boot menu and choose the dvd/cd drive. that should load the setup file. the windows disc does not load setup onto the hard drive. if you're running xp when you have the option hit 'r' to repair the computer, when you get into command prompt type sfc /scannow. this will search and fix all system files. you can also try chkdsk c: /r this will fix any errors in the file structure. good luck

If you need further help, reach me via phone at https://www.6ya.com/expert/joel_63c670a84e9f6a97

Jan 30, 2012 | Packard Bell iMedia Computers & Internet

1 Answer

I have a Packard Bell Imedia desktop not sure of the model. It was working fine until recently, I switched on my pc and after the boot screen "NTLDR is missing Alt Ctrl Del" message appeared....


Remove the hard disk and attach it to an USB hard drive adapter and then connect it into the USB port of a working computer. This computer will detect the hard drive as an external storage device, then you can open the various folders and files to copy your files to this computer or burn your data to a CD/DVD disc or USB flash drive.
Return you hard disk back to your Packard Bell so you can reinstall Windows.

Aug 10, 2011 | Packard Bell iMedia 6826 (P481000502) PC...

2 Answers

Acer aspire laptop wont boot


y dont u dispose it off if it is a problem computer, i guess it is a generic problem of laptop need to replace motherboard or so. avail warrent if it has...

Nov 25, 2008 | Acer Aspire 5100-5033 Notebook

1 Answer

New HDD Install Prob


Basic Troubleshooting Tips after Installing a New Hard DriveBased on Seagate IDE hard drives.

If you have installed your drive and it does not function properly, perform the following basic checks:

Additional Troubleshooting Tips

If you have performed the preceding basic checks but the problem persists, follow these guidelines for troubleshooting specific cases: 
After you install your new drive, your computer will not boot, and no error message appears on the screen.
The screen remains blank when you power up the system. 
The system does not recognize the drive. 
The dealer partitioned and formatted the drive for you in the store, but the drive does not respond when you install it. 
The system hangs in FDISK or fails to create or save the partition record. 
The system error message, "Drive not Ready," appears. 
The FDISK error message, "No Fixed Disk Present," appears. 
The drive does not format to full capacity. 
The DOS message "Disk Boot Failure," "Non-System Disk" or "No ROM Basic - SYSTEM HALTED" appears. 
The system error message, "HDD controller failure" appears. 
After you install your new drive, your computer will not boot, and no error message appears on the screen.

Check your computer manual or BIOS manufacturer to determine whether your BIOS supports drives that have more than 4,092 cylinders. If your system has this limitation, use the following procedure to configure your computer:

Turn off your computer, open the case, and remove your new drive.

CAUTION: To avoid electrostatic discharge damage to your computer or hard drive, make sure you are well grounded before touching the drive, cable, connector or jumpers.

Move the jumper on the alternate-capacity jumper, as shown in Figure 6. This causes the drive to appear to your BIOS as having a 2.1-Gbyte capacity (4,092 cylinders, 16 heads, 63 sectors per track). You may need third-party partitioning software, such as Disk Manager, to achieve full capacity of the drive. 
Remount your drive in the computer and replace the computer cover. 
Insert a bootable system diskette into drive A and turn on the computer. It should boot from drive A and automatically detect the new drive as a 2.1 -Gbyte drive. 
Insert your DiscWizard diskette into drive A and type A:XDM. Then press ENTER. This runs the Disk Manager program. 
Follow the Disk Manager instructions to install the dynamic drive overlay and to partition and format your new drive to its full capacity. 
After Disk Manager is done, reboot your system. You should see the Disk Manager banner and be able to access the full capacity of your new drive. 

The screen remains blank when you power up the system. 
If the steps listed above do not remedy this problem, try the following: 
Make sure the monitor is plugged in and turned on. 
Check all cards. 
Make sure the video card is seated in its slot and secured with mounting screws. 
Turn off the computer and remove the drive host adapter. If the screen turns on after you reboot, the host adapter may be incompatible or defective. If so, see your dealer. 

The system does not recognize the drive. 
Check all cables. 
Make sure the power supply is adequate for system needs. 
Reboot the computer and listen to make sure the drive motor starts up. If the drive is very quiet, it may be difficult to hear its discs reach operating speed. If the drive motor does not start up, recheck all drive cables. 
Verify that for each drive, a drive-type is listed in the system setup program. 
Try rebooting your computer by pressing the CTRL, ALT and DELETE keys simultaneously. If the drive is recognized after you reboot the system, the computer BIOS test may be completing before the drive is ready. 
One solution is to slow the processor speed during startup. If your computer has a turbo switch, set it to slow speed before turning the computer on. If there is no turbo switch, you may be able to use keyboard commands; see your computer manual for details. After the computer is up and running, return the processor to the fast speed. 
Another solution is to warm-boot your computer after every power-on. 
Check for I/O address conflicts. To isolate the conflict, verify that the drive and host adapter are compatible with your computer. Turn off the computer and remove all the peripheral adapter cards except for the video card and host adapter. If the computer recognizes the drive when you reboot the computer, turn off the computer. Reinstall the other peripheral cards, one at a time, until the conflict reoccurs. After you have isolated the source of the address conflict, you can resolve the conflict by changing the 1/0 address of the peripheral that appears to cause the conflict. 
If Disk Manager has installed the DDO on your hard drive and you have booted directly from a diskette, the information in the boot record for the drive may not have been loaded. Make sure there is no diskette in drive A and reboot. If you want to boot from the diskette, follow the "Booting with a Diskette" instructions under "Advanced Disk Manager Options" on page 20. 

The dealer partitioned and formatted the drive for you in the store, but the drive does not respond when you install it. 
Reboot the computer and make sure the drive spins up. 
Check all cables. 
Make sure the power supply is adequate for system needs. 
Make sure the DOS or Windows version the dealer used to partition and format the drive is the same version you have installed in your computer. If it isn't, see your dealer. 
Verify the drive-type values in the system setup program. You must install the drive using the same drive-type values your dealer used to partition the drive. 
Check for 1/0 address conflicts between peripheral cards. 
Check for viruses. 

The system hangs in FDISK or fails to create or save the partition record. 
Check all cables. 
Your setup system diskette may be corrupted. Try using a backup diskette. 
Make the partitions smaller. 
Change the interrupt jumper setting on the host adapter. 
Some BIOS have a Track 0 protection feature that protects Track 0 from viruses. This may cause FDISK to hang the system. You must disable this feature in the system setup program before you can use FDISK. See your computer reference guide for assistance. Be sure to re-enable this important feature when FDISK is done. 

The system error message, "Drive not Ready," appears. 
Check all cable connections. Make sure pin 1 of the drive is connected to pin 1 of the hard-disc controller or host adapter. 
Make sure the power supply is adequate for system needs. 
Reboot the computer and make sure the drive spins up. 

The FDISK error message, "No Fixed Disk Present," appears. 
Make sure the power supply is adequate for system needs. 
Verify the drive-type values in the system setup program. 
Check for 1/0 address conflicts. 

The drive does not format to full capacity. 
Verify the drive-type values in the system setup program. One of the following problems may have occurred: 
The values may be set with an incorrect translation characteristic. 
You may have entered a parameter value that exceeds the physical capacity of the drive. 
You entered a translation characteristic that does not take full advantage of the drive's capacity. 
The drive's physical specifications exceed the translation limits imposed by the BIOS.

CAUTION: If you change the drive-type values in the system setup program, you must partition and format the drive again. This erases data on the drive. 

If you have partitioned the drive into individual logical drives, you may need to make the partitions smaller to access the full drive capacity. 
If your computer supports LBA mode, you may need to enable LBA mode in the system setup program to access the full capacity of the drive. Refer to your computer's reference guide to find out how to enable LBA. 
Your computer may not support drives that have more than 4,092 cylinders. Follow the instructions on page 25 for After you install your new drive, your computer will not boot, and no error message appears on the screen. 

The DOS message "Disk Boot Failure," "Non-System Disk" or "No ROM Basic - SYSTEM HALTED" appears. 
Reinstall the DOS system files using the DOS SYS utility. 
Check all cables. 
Use FDISK to verify that the primary partition is active. 
Check for viruses. 

The system error message, "HDD controller failure" appears. 
Confirm the jumper settings on the drive. 
Verify the drive-type settings in the system setup program.
If a problem persists, please search for a solution or post a question in our tech support forum in our Help Desk.

Oct 19, 2008 | Computers & Internet

1 Answer

Old Packard Bell


try to see if bios jumper is in normal mode or pur battery off for a few minutes and see if it works

Dec 18, 2007 | Packard Bell (181379) Motherboard

1 Answer

Doesnt boot up


Hey, Blackchuck, try this
When you power up, try to get into BIOS and see what you get.
Let me know and we'll go from there.
Ron-

Nov 09, 2007 | Packard Bell Easy One Silver 2120 Notebook

1 Answer

Boot


Since you forgot the password best thing to do is make the cmos forget it. The way to do this is remove the cmos battery. Take it out for several hours then put it back in. This will reset the cmos and you should gain access.

Sep 20, 2007 | Packard Bell (181379) Motherboard

Not finding what you are looking for?
Intel DG965WH Motherboard Logo

120 people viewed this question

Ask a Question

Usually answered in minutes!

Top Intel Computers & Internet Experts

Alun Cox

Level 3 Expert

2678 Answers

David
David

Level 3 Expert

781 Answers

vsri9

Level 2 Expert

73 Answers

Are you an Intel Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...