Question about Mitsubishi VS-5047 50" Rear Projection Television

1 Answer

Television Problem When Television is turned on it turns immediately back off. Wondered if there was any way i could fix it

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer
Re: Television Problem

First off can you answer this:Is it possible to hook up my Mitsubishi 60" Gold rear projection tv (with Picture in a Picture capabilities) to my "Direct TV DVR", Phillips AV receiver and Phillips DVD player so I can receive picture in pictures of diferent channels i want to view of my "Direct TV" satellite provider. If so I would be glad to pay you for the easy to follow directions and drawings of the possible solution to my problem.

Posted on Sep 21, 2007

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer


Most common is convergence chips problem.

Apr 19, 2010 | Mitsubishi WS-65807 65" Rear Projection...

1 Answer

Sony LCD turns off 34 flash turn on 30sec repeats ...

The self-diagnostic function of the projection television will cause the STANDBY light to blink or flash when the television detects an issue. The number of times the STANDBY light flashes corresponds to a specific issue, some of which you may be able to resolve without the need for service.
  • If the STANDBY light flashes three times in sequence, the lamp cover is not securely attached. Reattach the lamp cover to resolve this issue.
  • If the STANDBY light flashes four times in sequence, the television may be overheating. To resolve this issue, ensure that the back of the television is well ventilated.
NOTE: If the television will not turn on immediately after being turned off, wait for the fan to finish its cycle, then attempt to turn it on again. This is part of the cooling process of some projection televisions and is normal operation.
If the flash sequence is not listed above, or the light continues to flash after troubleshooting the indicated issue, follow the steps below to perform a power reset on the television:

  1. Turn off the television. IMPORTANT: For a projection television that uses an internal lamp, wait 5 minutes after turning off the television to allow the lamp to cool before continuing with the following steps.
  2. Unplug the television power cord from the electrical outlet.
  3. Let the television remain without power for 60 seconds.
  4. Plug the power cord back into the electrical outlet. NOTE: If the television is plugged into a power strip or surge protector, remove it from the power strip or surge protector and plug it directly into the wall outlet. If the issue is resolved, the problem is with the power strip or surge protector and not the television.
  5. Turn on the television.

If the issue is still unresolved after following all of the troubleshooting steps, service may be required. Please note the number of times the STANDBY light flashes and relay that information to the service center.


Dec 14, 2007 | Sony Grand WEGA KF60XBR800 60" Rear...

1 Answer

Panasonic Cinema Vision Clicked Off

try bulb if not if not than it doesnt sound good for your t.v

Sep 14, 2009 | Panasonic PT-47WX49 47" Rear Projection...

1 Answer

Same problem

Look for a factory reset in the users manual. If you don't have the manual, it's available at

Jun 12, 2009 | Samsung HC-P4752W 47" Rear Projection...

1 Answer

No picture, no sound, turns on, but turns itself off immediately.

unplug 2 ribon cables they are white then plug them back in  should fix it 

Jun 08, 2009 | RCA HD52W66 Projection Television

2 Answers

Why does my GE 46GW945 46 in.TV turn on and then right back off?

this is weak power distribution throughout the unit. you wil need to test the power supply board for blown capacitors and resistors as well. replace this vital board if you notice any swollen or disscolored componets.

May 23, 2009 | GE 46GW945 46" Rear Projection Television

1 Answer

No sound, no picture, blinking LED.

You must use the original stk 392-110 and stk 392-150 and do not mix them up. There is one of each.

All the suggestions about substituting other ICs for 110's are Bullplop, except for Hitachi manufacturers upgrade with changed resistor values included.

Oct 25, 2008 | Hitachi 46F500 46" Rear Projection...

1 Answer

Pioneer SD-P4552 turns off immediately after turning on

Good Day, vash4056;

Don't dig a hole yet I'll will have to some more research.

Okay?? big IRISH.

Aug 07, 2008 | Projection Televisions

1 Answer

Mitsubishi Big Screen VS-45607

probaly bad wiring or shorts in the wires or something is intefearing with your tv if it is wiring it might be a fire hazard

Feb 13, 2008 | Mitsubishi VS-45607 45" Rear Projection...

Not finding what you are looking for?
Projection Televisions Logo

142 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Projection Televisions Experts

matt martin
matt martin

Level 3 Expert

1187 Answers

Jaime Hernandez

Level 3 Expert

2267 Answers

The Knight
The Knight

Level 3 Expert

66413 Answers

Are you a Mitsubishi Projection Television Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides