Question about Cobra 148 GTL 120-Channels Base CB Radio

1 Answer

Need to change mic jack . wires came unhooked which wire goes where ?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Guru:

    An expert who has written 7 tips or uploaded 3 video tips

  • Master
  • 773 Answers

If it is a 5 pin then..
Looking from inside the radio at the mic jack, with the nub down. Starting from the left is pin 1, pin 2, pin 3, pin 4, and pin 5.

here is the colors that should be attached to each.

1 is white.
2 is sheild.
3 is black.
4 is red.
5 is blue.

Here is a 4 pin explanation:

Again looking from inside the radio, with the nub down. Starting from the left, Pin 1, Pin 2, Pin 3, Pin 4.

Pin 1 is red.
Pin 2 is white.
Pin 3 is blue.
Pin 4 is black.

Posted on May 03, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Tring to wire up sadelta hand mic the mb-4 to the superstar 3900 but dont know the wiring there are 5 wires the couler of the wires are screen white red green andbrown can you help


I would like to state there are two ways to do this, one way is too open the radio cover up and look at the back of the jack where the mic goes and the color of the wires should be the same, or you can do it the second way which is a little longer and patience to do take the wires of the mic and touch one at a time to a prong one should get you sound when its right the other should transmit when you push the handle to talk on the mic

Jun 02, 2014 | Superstar 3900

1 Answer

Galaxy dx 44hp, no am audio or mod ,fm & pa ok


Have you tried another mic. First guess microphone wire broke or broke solder for audio wire in mic jack at mic cord.

Mar 26, 2014 | Galaxy Radios DX-44HP Mobile Amateur Radio

1 Answer

I need to wire a silver salute mic to a cobra 142 gtl 5 pin what color wire goes towhat mic pin


dont go by colors.. go by what wires are on the switch and mic element.. mics can be rewired and no one told you the colors could have changed FYI..

Pin #1 ~ Audio
Pin #2 ~ Shield
Pin #3 ~ Receive
Pin #4 ~ Switch Wire
Pin #5 ~ Transmit

always go by connections not color of the wire. that way you learn and you can do any mic. to any radio.

Nov 30, 2013 | Radio Communications

1 Answer

HOW DO I INSTALL ROGER BEEP ON A GALAXY 33 CB RADIO


Does the roger beep come with instructions? It can vary between beep boards.

Typically it gets installed inline with the mic jack.

There is a wire or pin on the board where the tx wire, and the rx wires go.These wires get disconnected from the mic jack, then a wire goes to the tx pin. Then there is an audio wire that gets connected to the audio wire of the mic jack. Then the black wire to ground, and the red wire to switched 12v right off the power switch.

Here is a schematic of the board connected to the mic jack so you know what pin is what.

Again, I would need to know what roger beep board you would like to install.


Feb 22, 2010 | Galaxy Radios DX-33HML 40-Channels Base CB...

1 Answer

148 gtl 5pin


Looking from inside the radio at the mic jack, with the nub down. Starting from the left is pin 1, pin 2, pin 3, pin 4, and pin 5.

here is the colors that should be attached to each.

1 is white.
2 is sheild.
3 is black.
4 is red.
5 is blue.

Hope this helps. Take care in soldering. It is easier to reach the pins if you remove the 4 screws that hold the face plate on. Be careful not to pull another wire from somewhere.

Apr 20, 2009 | Cobra 148 GTL 120-Channels Base CB Radio

1 Answer

Need proper wiring for the J9C2 connector pinout


The User Manual for this m/board (E210882) can be found at :- ftp://download.intel.com/support/motherboards/desktop/d865glc/BFLC_English.pdf
you will need adobe free reader to view it. refer to pages 40 thru 46 for the front panel header and isb info.

Apr 01, 2009 | Dell Dimension 4600 PC Desktop

4 Answers

Conection


Find the Audio card of you computer. Mostly audio card jack had label line out or audio. Also audio out jack was light green in color.

Jun 17, 2008 | Boka 81000 Computer Speakers

2 Answers

How to wire a headset to stereo phone jack.


http://en.wikipedia.org/wiki/TRS_connector#Tip.2Fring.2Fsleeve_terminology

the table shows u what u need i think

Oct 25, 2007 | Cell Phones

Not finding what you are looking for?
Cobra 148 GTL 120-Channels Base CB Radio Logo

Related Topics:

195 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cobra Radio Communications Experts

AnyMHz.com
AnyMHz.com

Level 2 Expert

500 Answers

Steve

Level 3 Expert

3287 Answers

Brad Brown

Level 3 Expert

15691 Answers

Are you a Cobra Radio Communication Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...