Question about IOGear HAND-HELD RF WIRELESS MOUSE (S2696984)

1 Answer

Trouble tracking vertically

I have had this a few weeks and it seems to work OK but more and more it refuses to track vertically but does fine horizontally. Anything I can do?

Posted by on


1 Answer

  • Level 1:

    An expert who has achieved level 1.


    An expert who has answered 20 questions.


    An expert that hasĀ over 10 points.


    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 35 Answers

Dust stuck inside the trackball on the vertical axis maybe. Otherwise faulty device, you should return it

Posted on Sep 22, 2007


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Power driver seat will not fully move forward or backward.

make sure nothing is lodged under the tracks this is common things get thrown under the seat and stops them in the track

Mar 31, 2014 | 2002 Chevrolet Tahoe

1 Answer

Sony cdp cx 355 skips on first track

Could be some dust or debris in the unit. Also be careful that you are not putting fingermarks near the hole section of each CD you put in, as the CD plays from the centre out.

Jul 02, 2017 | Sony MegaStorage CDP-CX355 300-Disc CD...

1 Answer

Strange recording problem - no diagnostic messages

Sounds like the servo is shot on the deck that moves the laser. MDS JE520 is a nice early deck 1998-1999 vintage, so it's had a great run and I'd look for another on eBay or at a "hamfest" swap & shop for parts.

Mar 26, 2010 | Sony MDS-JE520 Mini Disc Player

1 Answer

It won't track reliably. It plays OK for the first few tracks of a CD, then has trouble tracking. Finally it just sticks.

Try cleaaning the lead screw that moves the head. Often they get dust particles which jam up the works. REMEMBER that CD's read from the inside tracks outward.

Dec 23, 2009 | Sony SCD-CE595 5-Disc CD Changer

1 Answer

Discs will not eject, unit makes strange clicking noise

HI, the gear track is stripped and the load motor is stuck between the good section of the track and the bad section of the track. you will need to replace the loading dock in your unit. this will fix this issue.

May 27, 2009 | Teac CD-RW880 CD Player / Recorder

1 Answer

Suspension or tracking? The car doesn't sit like it used to

i think you go to other shop foe second opinion, for allignment, sometimes be an defective tire

Apr 24, 2009 | 2005 Audi A3

1 Answer

Cluster PCB

sorry i don't have a photo yet, but what i did was remove a small section of the laquer from the track on the PCB about 1/2 inch away from the plug socket, then pre-tinned & soldered a small insulated wire (small speaker wire, only 1 part of the figure 8 cable) from the bottom right plug track (common pos for the warning lights) to the solder joint @ the lower end of the under PCB link that goes to the bottom left screw fitting of the tacho, this bypassed the crack in the PCB,
if there is "NO" burn marks & it is only a cracked track you will-not have any problem in bypassing the crack with a small wire, or even running a small solder track along the PCB track, just remember to remove the laquer, kind regards waz

Nov 27, 2008 | 2002 Mitsubishi Lancer

1 Answer

Tracking seems off

I have had the same problem. There is no way to manually adjust the tracking on this Hitachi, or on most 8mm cameras, for that matter. I copied all of my more recent tapes to DVD first (2 copies of each) and then I went to the oldest tapes, which for some reason were OK. When I got to one tape that gave me trouble, I just let it play in the camcorder for about an hour. It adjusted its own tracking so that the picture was OK. Then, I rewound the tape and copied that one. I still have 2 tapes that will not adjust. I am going to send those out to a copying service. I hope they can adjust the tracking and make the copies I need.
By the way, I used this camera and a Panasonic DMR-E55 to make the DVD copies.

Jun 04, 2008 | Hitachi VME545 Camcorder

1 Answer

ETrex Vista shows incorrect date

Thanks for the great advice. My problem is fixed!! Yay!

Nov 18, 2007 | Garmin ETREXVISTA GPS Receiver

Not finding what you are looking for?

Related Topics:

194 people viewed this question

Ask a Question

Usually answered in minutes!

Top IOGear Computers & Internet Experts

Greg Cann
Greg Cann

Level 3 Expert

1114 Answers

John Anderson
John Anderson

Level 2 Expert

310 Answers

Cindy Wells

Level 3 Expert

5306 Answers

Are you an IOGear Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides