Having trouble adjusting settings - Cooper Wiring OS306U-W-K Passive Infrared Wall Mount Occupancy Vacancy Sensor White

Somewhere on the lower part of the dash, you will find a small thumbwheel that increases the brightness.

It might be shown in here. 'Year make model' are important.

Time Setting
Sets the time and date of the player. to adjust the values and then press the VOL button to move to next selection. When all values have been adjusted press the Menu button to accept and return to previous menu.

need vacuum gauge, take one carb and adjust till highest vac setting. then match next carb to first carbs settings (same vac) if u can't match adjust first carb to 2cd carb's highest vac setting. make sure engine is warmed up first.then ride

Be shure the guns are set properly follow below:
ADJUSTMENT PREPARATION:

• Pre Heat Run should be finished.
  
• Be sure Screen Color Temperature setting is in the COOL mode
  
• Room Light should be minimal.
  

ADJUSTMENT PROCEDURE:

1. Go to I2C ADJ. Mode. (With power Off, press the INPUT button on front panel and then press the POWER ON button then release. The Service Menu is displayed.)
   
2. Set R DRV (COOL) to center data value (3F).
   
3. Set G DRV (COOL) to center data value (3F).
   
4. Set R, G, and B CUTOFF (COOL) data settings to [80].
   
5. Adjust Screen VRs on Focus Pack fully counter clock wise.
   
6. Choose SERVICE item [1] of I2C ADJ. Mode. Select CURSOR RIGHT and the Vertical will collapses.
   
7. Adjust any Screen VR. Screen VR should be turned clockwise gradually until that particular color is barely visible.
   
8. Repeat for the other two colors.
   
9. Exit SERVICE MODE by pressing the CURSOR LEFT on remote.
   
10. Exit SERVICE MENU by pressing the MENU key on remote.

ok, if you do have a sound problem it is separate from the convergence trouble; this set uses two STK-392-110 ic's. you need to change both and any of the resistors near them that may be gone or open---then adjust the set with the original remote--you can do the adjustments in the customer menu or if needed in the TECH menu-I can tell you how to get into that menu--if you have no sound from the speakers in the set that is a separate issue.

I do this here for free--if you have questions or need help reply here--if this has helped you give me a vote here.

Most of these sets with a convergence problem just need the two chips replaced and the set adjusted---you can buy both chips on Ebay for less than 14 dollars plus shipping.

This depends on how muddy or clear the water is. If muddy or there is a LOT of floating sediment in the water, most fishfinders will have trouble getting a good image through the dirty/brackish water. You might not be doing anything wrong in this case.

Sensitivity and grayline are your main adjustment settings, assuming you have your transducer located correctly at the right depth in relation to your hull and the waterline as well.

Does the clutter extend all the way from the surface to the bottom? If so, try reducing sensitivty... if clutter is moreso near the surface or top of the screen, then this is probably because the transducer is getting aerated water or distrubed water over it and causing the clutter and readings.

As a good rule, match the sensitivity setting tot he grayline setting. I.e. if you have sensitivity at 90%, put grayline at 90% also.

Hope that helps!

• 2 ways to adjust the volume:
• system volume and sound card icon settings:
  
• 1. click the volume icon on the system tray and a window will pull up, adjust accordingly
  
• 2. click the sound card icon on the system tray and adjust it according as windows pulls up.
  

http://www.brother.ca/en/products/pdf/manuals/GX6750-UG.pdf

Page 2, Section 4 describes how to set the margins

Pasted from the manual:
1 In the Clock priority mode, press and hold
TITLE/ for at least 2 seconds while the time is
displayed.
The time indication will blink.
2 Turn the Rotary encoder (CDE-9846 only) or
press up or down arrow (CDE-9842 only) to adjust the
hours while the time indication is blinking.
3 When the hour has been adjusted, press the
Rotary encoder (CDE-9846 only) or press MODE
(CDE-9842 only).
4 Turn the Rotary encoder (CDE-9846 only) or
press up or down arrow (CDE-9842 only) to adjust the
minutes while the time indication is blinking.
The time is automatically set 5 seconds after the minute
adjustment. The time can also be manually set by
pressing the Rotary encoder (CDE-9846 only) or press
MODE (CDE-9842 only).

These height adjustments are designed so that they will not adjust when the handle is in the "back" position. This is so they will stay where they are set and not self-adjust while you are vacuuming. To change the setting, you need to return the handle to the upright position and the adjust the setting and the machine will go to that position when the handle is lowered.