My unit runs for 10 to 15 minutes and turning off. We need to wait for about 20 minutes and push the start button and goes on normal. I think that is a over heat problem or bad thermal sensor. I need the wiring to trouble shut it.

Sounds like the fuel pressure regulator. if you have access to a pressure guage check the pressure when it will not start.

Have the fault codes read. Replace faulty items. Use only genuine items as non-genuine replacement are not always compatible with the OEM fitted CPU units I suspect corroded wire connectors

I have exactly the same problem started last winter, ran fine all summer then as soon as it got below freezing again if I start it and run for 15 20 minutes wont restart I have to let it sit for 20 minutes or so and then it will start again. no codes and just turns over without starting. cant be fuel pump like i said had this problem last winter then ran fine all spring summer and fall! Anybody got the answer for this one??

you may need to replace the capacitor that starts the motor

Due to battery being disconnected while timing belt was replaced, You will need to go through the IDLE RELEARN PROCESS.

In order to make the engine run normal again, you need to take the car through a relearn process. Otherwise the idle could be very slow or have a 30mph idle.

To enable it to relearn, here's what to do.

1) Disconnect the battery cable for 15 minutes, before hooking it back up.

2) (KOEO) Turn the Key On with Engine Off, just so the electronics are on, but without starting the engine and turn the climate control panel to off.

3) Push the off and warmer buttons on the climate control panel at the same time and hold for up to 5 seconds for the computer to go into diagnostics.
On the fuel panel screen it will display 888 then E52 and then 70.
When it gets to 7.0 shut off the key for 1 minute.

4) Repeat step 3, two more times.

5) Start the engine without pushing on the accelerator pedal and let it run for 18 minutes with the climate control panel off.

6) After 18 minutes put your foot on the brake and shift into drive and wait 1 minute.

7) Then turn on the a/c by pushing the auto button. It needs to be warmer than 60 degrees F so the compressor can engage. Wait 1 more minute.

8) Put the shifter back in park and turn the key off.

9) Wait 1 minute

10) Idle relearn is now complete and the engine should start and run correctly.

follow directions from the owners manual. while unit is powered up, unplug power cord from back of unit - wait 5-seconds. Depress the DVD open/close button while re-plugging the power supply cord to the unit. LG splash appears onscreen and unit goes into re-set. you do not loose any of you programing or settings.

Be sure its all the way in park or try neutral.Its possible that security system does not recognize the key. Is security light flashing or on steady? Shut all doors and windows,trunk,hood, turn off all accessory's,roll down drivers window, turn key off and remove for at least 1 minute, insert key into ignition, try to start leaving key to run position for 20 minutes, turn key to off,wait 15 seconds, try to start again leaving key to run, wait 20 minutes, turn key off,wait 15 seconds, try to start, This should relearn key code. It may relearn after 1 learn cycle and start if system is ok. Hope this helps and that the weather is dry and warm for this procedure!.. i think this may solve ur problem..

thank u rate me!!!

Be sure its all the way in park or try neutral.Its possible that security system does not recognize the key. Is security light flashing or on steady? Shut all doors and windows,trunk,hood, turn off all accessory's,roll down drivers window, turn key off and remove for at least 1 minute, insert key into ignition, try to start leaving key to run position for 20 minutes, turn key to off,wait 15 seconds, try to start again leaving key to run, wait 20 minutes, turn key off,wait 15 seconds, try to start, again leaving key to run, wait 20 minutes, turn key off, wait 15 seconds, try to start. This should relearn key code. It may relearn after 1 learn cycle and start if system is ok. Hope this helps and that the weather is dry and warm for this procedure! This is not always a fix, but works most of the time.

at leas 15 yrs old??? think it's done its time, its a great machine andwould reccomend replacing with a whirlpool/kenmore unit again.no tworth servicing in my opinion, average call here in new york 150-225, anbd those are for simple issues. id rather put money into new unit! bit be sure to check your venting id say 85% of dryers taking too long to dry are vent related issues

Hi,

i belive that your printer needs to be resetted. Just try the reset options which are for HP 6110xi.

POWER DRAIN:-Turn off the printer, Unplug the power cable from printer and from the wall outlet.Press and hold ON buton for 30-60 seconds.


PARTIAL RESET:-Unplug the printer power cable while its ON, press and hold # and 3 button and connect the Power cord while holding.Wait untill the ON light flashes, then release the buttons.

----(for below reset cartridges must be removed out)---------

SEMI_FULL RESET:-Unplug the printer power cable while its ON, press and hold # and 6 button and connect the Power cord while holding.Wait untill the ON light flashes,or wait for 20 seconds,hen release the button.If the printer goes off dont worry release the button and Push the ON button.


FULL NVM RESET:-Take the Ink Cartridges out, Unplug the printer power cable while its ON, press and hold OK and CANCEL button and connect the Power cord while holding the buttons.keep Holding the buttons until the printer goes off ,release the button and Push the ON button.

(Notes - resets will take a while)


Thank You