Question about Pioneer inno2 Portable XM Satellite Radio Receiver with Home Kit - Black

Open Question

Inno2 stuck in "please wait mode"

With radio in cradle screens displays "please wait" for a few seconds then goes white for 2 sec: then darkens and reboots to "please wait screen"

Posted by on

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 3 Answers

SOURCE: white screen

I had the same problem with my Pioneer Inno Gex-Inno2BK XM radio receiver. One evening while leaving work, I gently took it out of the cradle & the screen suddenly went completely blank & all white. I could still hear music but there was no screen visible. Solution is this: (1) Gently remove the back cover which covers the battery. (2) Gently remove the dark blue square battery which is only about 1 inch (width) by 3/4 inch (height) by 1/4 of an inch in thickness. I removed mine by holding the receiver upside down & gently shaking it with one hand until the battery came out into my other hand. After about 4 or 5 gentle shakes, it came out. (3) Wait about 10 seconds. (4) Place battery back into XM radio receiver being careful to line the copper power receptable on the battery with a corresponding surface inside the receiver. Each copper area is only about 1/10 of an inch by 1/10 of an inch. Use this as a guide when putting the battery back in to make sure it's lined up properly. (5) Gently slide the cover back in place & let it snap into place. (6) Turn receiver back on by pushing power button like normal. (7) XM receiver should boot up with a full display just like new. All recorded songs are still in place. Nothing has been lost. Problem solved. Root cause of problem is probably some type of boot-up issue with the receiver in which the battery (i.e., the power supply) just happened to be slightly ajar...which also persisted even when placing the receiver back in the cradle until the above steps were taken. The steps above worked beautifully for me...Hope it works for you as well! Have A Great Day...Tom Armstrong

Posted on Feb 05, 2009

Ad
  • 2 Answers

SOURCE: white screen

tomarmstrong's solution works!! Just take out your battery, and put it back in.. should work fine.

Posted on Feb 22, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to how to unlock car radio 2008 Chevy Impala


Requirements
The theft lock radio must be in "LOC" mode.

Procedure:
1. Turn the ignition ON (The radio should display "LOC")
2. Hold down the Radio Presets 2 and 3 buttons for six seconds
3. The radio display changes from LOC to a three-digit number. Write this number down. You now have fifteen seconds to complete the next step.
4. Press the AM/FM button
5. The radio display changes to another three-digit number. Write this number to the right of the first one.
6. You now have a six-digit number, the first three digits are from STEP 03 and the last three digits are form STEP 05
7. Call 1-800-537-5140
8. Press 1 then # (pound). You'll hear "Invalid Code, try again"
9. Press 139010 or 106010 or 206010 or 202107 then # (pound). You will be asked to enter your four or six digit code followed by *
10. Enter the number from STEP 6 then *
11. Listen to the four-digit number and write it down. It will be repeated twice
12. Turn the ignition ON (The radio displays LOC)
13. Use the MN and HR buttons to enter the code from STEP 11
14. Press the AM/FM button. The radio display changes to "SEC". Your radio is now "un-locked" and usable.


Dealership Codes
  • 139010
  • 106010
  • 206010
  • 202107
Troubleshooting
If you fail to enter the correct code eight times, the radio goes into INOP mode. You have to wait an hour with the ignnition on before the radio returns to LOC mode.

Aug 14, 2015 | Cars & Trucks

1 Answer

Does pioneer have a car cradle for the inno2 that secures it better i have gone through so many of them and now my warranty is up. i operate heavy equipment and it causes my inno to fly out of the cradle,...


I feel your pain. Unfortunately, I haven't been able to find any car docks, there all discontinued. (sorry bums!)
But, when I'm riding my motorcycle, I put a rubber band around the radio and dock, holding it in place.
But, in a place that doesn't interfere with any buttons or the display.

Jun 06, 2010 | Pioneer inno2 Portable XM Satellite Radio...

1 Answer

My audio system is stuck in the 'loc' position. We didn't have a code so we can't unlock it. Suburban


How to Reset GM Theft lock Radio's

Article Disclaimer: This article is meant to be used by Delco Radio owners to reset there radios. In no way is it meant to be used for any unethical or unlawful ways.

Purpose

The following instructions will allow you to reset any GM (General Motors), Cadillac, Oldsmobile, Buick, Pontiac theft lock radio.

Requirements

The theft lock radio must be in "LOC" mode.

Procedure:

1. Turn the ignition ON (The radio should display "LOC")

2. Hold down the Radio Presets 2 and 3 buttons for six seconds

3. The radio display changes from LOC to a three-digit number. Write this number down. You now have fifteen seconds to complete the next step.

4. Press the AM/FM button

5. The radio display changes to another three-digit number. Write this number to the right of the first one.

6. You now have a six-digit number, the first three digits are from STEP 03 and the last three digits are form STEP 05

7. Call 1-800-537-5140

8. Press 1 then # (pound). You'll hear "Invalid Code, try again"

9. Press 139010 or 106010 or 206010 or 202107 then # (pound). "it's really *<star>lol"
You will be asked to enter your four or six digit code followed by *

10. Enter the number from STEP 6 then *

11. Listen to the four-digit number and write it down. It will be repeated twice

12. Turn the ignition ON (The radio displays LOC)

13. Use the MN and HR buttons to enter the code from STEP 11

14. Press the AM/FM button. The radio display changes to "SEC". Your radio is now "un-locked" and usable.

Dealership Codes

* 139010
* 106010
* 206010
* 202107

Troubleshooting

If you fail to enter the correct code eight times, the radio goes into INOP mode. You have to wait an hour with the ignition on before the radio returns to LOC mode.

Thank you for using fixya and good luck

May 10, 2010 | 1999 GMC Suburban

1 Answer

The screen doesn't flip when in the cradle. It


I just spoke with Pioneer for this same issue. They said they do not repair the inno2 because it's not cost effective.

Nov 27, 2009 | Pioneer inno2 Portable XM Satellite Radio...

1 Answer

The power went out at the office. when the power was restored my brother intellifax 5750e will not work. there is an error 77 message displaying on it's panel.


you can try this. press "menu/set" " *2864 " within 2 secs. then press "01" and wait for a few seconds until "para init" goes away. then press "99" and when you see "please wait" unplug machine. wait for 15 secs. and plug back in and see if it comes up. if not, then you have a hard error and must have serviced.
good luck,
razors

Mar 03, 2009 | Brother IntelliFAX 5750e Laser Fax

2 Answers

White screen


I had the same problem with my Pioneer Inno Gex-Inno2BK XM radio receiver. One evening while leaving work, I gently took it out of the cradle & the screen suddenly went completely blank & all white. I could still hear music but there was no screen visible. Solution is this: (1) Gently remove the back cover which covers the battery. (2) Gently remove the dark blue square battery which is only about 1 inch (width) by 3/4 inch (height) by 1/4 of an inch in thickness. I removed mine by holding the receiver upside down & gently shaking it with one hand until the battery came out into my other hand. After about 4 or 5 gentle shakes, it came out. (3) Wait about 10 seconds. (4) Place battery back into XM radio receiver being careful to line the copper power receptable on the battery with a corresponding surface inside the receiver. Each copper area is only about 1/10 of an inch by 1/10 of an inch. Use this as a guide when putting the battery back in to make sure it's lined up properly. (5) Gently slide the cover back in place & let it snap into place. (6) Turn receiver back on by pushing power button like normal. (7) XM receiver should boot up with a full display just like new. All recorded songs are still in place. Nothing has been lost. Problem solved. Root cause of problem is probably some type of boot-up issue with the receiver in which the battery (i.e., the power supply) just happened to be slightly ajar...which also persisted even when placing the receiver back in the cradle until the above steps were taken. The steps above worked beautifully for me...Hope it works for you as well! Have A Great Day...Tom Armstrong

Jan 19, 2009 | Pioneer inno2 Portable XM Satellite Radio...

1 Answer

Screen won't flip when in the cradle


Take it back the store where you bought it at. It sounds like a broken system?

Jan 09, 2009 | Pioneer inno2 Portable XM Satellite Radio...

1 Answer

Pioneer Inno Gex-INNO2BK stuck in re-boot cycle


I fixed the reboot cycleing problem by plugging the travel charger into the jack that also fits the home and car cradle. I had the Inno set to auto start when it was powered on in the car cradle. The travel plug must have over-ridden the auto-start setting and allowed it to finish the complete bootup. I then reset the Inno default settings and every thing was back to normal. I do not know what was the original cause of the rebooting cycle problem

Jul 28, 2008 | Pioneer inno2 Portable XM Satellite Radio...

4 Answers

Screen locked on "Checking media"


When the radio locks up on the Checking Media page you hold the + button to the volume and the MODE button wait for 3 seconds and it will turn off...  Thanks to Delphi for this assistance!!  Chris K.

Jun 02, 2008 | Delphi SKYFi3 XM Radio Receiver

Not finding what you are looking for?
Pioneer inno2 Portable XM Satellite Radio Receiver with Home Kit - Black Logo

Related Topics:

126 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pioneer Audio Players & Recorders Experts

 Grubhead
Grubhead

Level 3 Expert

5113 Answers

John
John

Level 2 Expert

509 Answers

T-Comtech Repairs
T-Comtech Repairs

Level 2 Expert

417 Answers

Are you a Pioneer Audio Player and Recorder Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...