Question about ASUS P4BGL-MX 845GL (AS04P4BGL-MX) Motherboard

1 Answer

HD LED and POWER LED Connection

Dear Sir, I had lost the manual of this mother board. I faces the problem of HD LED and POWER LED connection. Please help me .

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 71 Answers

Here is a link to the manual that should give you a diagram - http://dlsvr03.asus.com/pub/ASUS/mb/sock478/p4bgl-mx/e1339_p4bgl-mx.pdf - hope this solves your problem.

Posted on Sep 17, 2007

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Mother board manual for mx4lr


T got this from the Aopen website - hope it helps!


xayfj4aaaaasuvork5cyii=

Jan 15, 2012 | AOpen MX4LR (91.89Y10.002) Motherboard

1 Answer

I have mercury mother board and its having nine pinsocket for reset switch,power switch,hd led ,etc but i dont know their proper connections. there are some nos besides but not understandable . can you...


Hi Rajen samani!
Most mercury motherboards with a nine pin front panel connection use the following configuration.
joehaydu_0.jpg
You may want to double check to make sure that your motherboard follows this configuration. Just go to http://www.mercury-pc.com/downloads.php, enter your model number, and you'll be able to download the manual for your board. The jumper configuration should be in a section labeled "Front Panel Connection" or something similar.
Hope that Helps!

Mar 07, 2011 | Mercury Computers & Internet

1 Answer

Driver for ms 6526 ver 2


please detected the cd rom from the bios setting and check the data cable connection of mother board and the cdrom

May 05, 2010 | Intel Motherboard

1 Answer

Power connections for tower led's


The manual in question can be located here

http://download.intel.com/support/motherboards/desktop/sb/d1047103_en.pdf

It is a pdf file, so you will need ADOBE,
I have checked and the pinout for the front panel connectors is there.

May 24, 2009 | Intel D945GTP Motherboard

1 Answer

Need help with enachine t2528 wiring power sw wire on mother board


If you open the CPU cabinet you will find the front panel connection pins at opposite right corner to the motherboard IO ports (where we connect all the power,monitor,keyboard,mouse chords) You can easily identify it as below these pins it will be named as P_Sw or P_Bt,Pw_led ,Hdd_led etc

May 09, 2009 | Computers & Internet

2 Answers

845 mother board. ps2 keyboard connection are not working.


do not connect power led r remove if connected i had the same problem and this was the solution

Dec 21, 2008 | Intel D845HV (735858149143) Motherboard

3 Answers

Need to connecte wires to power sw, HHD Led etc. for pm8m mother board


You can download the manual from this site to connect the wires. If you need further help just respond to this post or thread

http://www.graficall.nl/pdffabrikant/4710F.pdf

Sep 02, 2008 | MSI PM8M-V Motherboard

2 Answers

Mother Board connection


Go to the site below. Its a manual for the 800/i65GV group. Go to page 67 and zoom in. You'll get a nice look where everything goes. Two rows of pins. Upper row and bottom row. Real close to each other. Do not place connectors up to down. Connect only left to right.
The reset connector has two pins. One will be white or black. These are - grounds. So connect it to the bottom row onto the most right two pins. Moving to your left. Skip one pin. Take the Power Switch a two pin connector. Remember Black & White is ground & ground goes to your right for both rows of Mb pins.
http://dlsvr03.asus.com/pub/ASUS/mb/sock478/p4p800/e1324_p4p800.pdf
Go to IDE_LED next. Its the last two pins towards your most left of the bottom row of pins. Move to the upper row & the power LED. Same as the bottom row keping the grounds to your right. Lastly is the speaker. Its connector holds four pins but you only use two. One in each end.

Good luck & please vote....

Dec 22, 2007 | Intel PENTIUM-4 865GV CHIP MOTHER BOARD...

Not finding what you are looking for?
ASUS P4BGL-MX 845GL (AS04P4BGL-MX) Motherboard Logo

Related Topics:

477 people viewed this question

Ask a Question

Usually answered in minutes!

Top ASUS Computers & Internet Experts

Les Dickinson
Les Dickinson

Level 3 Expert

18424 Answers

Alun Cox

Level 3 Expert

2678 Answers

Doctor PC
Doctor PC

Level 3 Expert

7733 Answers

Are you an ASUS Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...