Question about Hoover HTC243 Top Load Washer

1 Answer

Hoover 710 top load washer

Renewed spin soleniod. but have misplaced wiring diagram,need to know where the following wires go. Blue, Yellow, Red/black/White, Green/Yellow, Brown/Grey/White, Brownishred/White

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.


    An expert that has over 500 points.

  • Expert
  • 351 Answers
Re: hoover 710 top load washer - Hoover HTC243 Top Load Washer Washing Machines

They sound

Posted on Mar 02, 2008

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

I have a Hoover Top Loader HNT2135. The problem is that it will not spin. Makes a noise as though it is going to spin but doesn't manage to.


If it does make noise and does not spin it is usually the drain pump clogged. Disconnect power, reach the drain pump and check for blockage in there . If that is not the problem check in order drain hose at the back, lid switch, pressure switch, and finally pump and motor from underneath the washer. The switches and motors can be tested using a multimeter.

Here a page about drain/spin problem.

If you need parts see this tip explaining how to find parts and diagrams for most appliances: Where do I find parts and diagrams for my appliance?



Sep 13, 2011 | Hoover Nextra HNT 2135 Top Load Washer

2 Answers

I have a Hoover Zodiac12 2-speed reversible motor i want to use for a home project. Its a Nuova Ibmei with 5 terminals. The wires are L to R and top to bottom; 1. black stripe, 2. blue, 3. yellow, 4. red...

You will destroy the motor by running it with multiple speeds tied together. So be careful. Just try and get it to work with 2 wires and tape the others off away from each other and the frame so they won't short anything out. themobilian_795.jpg

Jan 04, 2011 | Washing Machines

1 Answer

Everything works but will not spinfast enough to spin the water out. It spins very slow if it spins at all.

Either the belt needs replacing or the high speed windings of the motor are failing. You should have about 1 ohm on each of the winding leads. This is the plug on the motor. Refer to the tech sheet or wiring diagram for what wires are for low speed and what one is for high speed. It is usually the blue or yellow for high speed. Check from the common (white wire) to each of the other terminals ( blue or yellow) and if it is more than 1 ohm the motor will need to be replaced. If it is good the transmission is likely bad.
here is a link for the motor of a similar type
and here is a link for disassembling

Jun 24, 2010 | Hotpoint VWSR4160GWW Top Load Washer

1 Answer

I need to know how to wire the motor on a kenmore belt driven washer----i.e. which wires go to which as the plugs on the end of the wires were removed and know the spin does not work

First, see the Sears parts site for your washer:

Enter your model number and you'll see a list of major sub-components with diagrams and parts.

From there you may be able to get PDF files of manuals for your washer.

Since Whirlpool makes most of the Kenmore washers, see the whirlpool site that lists PDF's for many of their products.

Without a model number, it would be difficult to try to track down the wiring diagrams.

Sep 26, 2009 | Kenmore 24032\24036 Top Load Washer

1 Answer

Frigidare top load mod# FWS445RFS2. Motor shaft spins on belt but will not engage tub. problem began going into final spin cycle. Tub pulley can be turned by hand and clutch appears to engage belt. What do...

Hi, you should check your wash and spin solenoid, located on gearbox assembly, or check for any device, that has wires connected to it, on gearbox, it's two soleniod, one for wash, one for spin, remove wires from solenoid, check for resistance, with ohm meter, looks, like your wash solenoid are burnt out, sometimes, they burnt out, if it's burnt out replace it. good luck.

Aug 08, 2009 | LG WM2077CW XL Front Load Stackable Washer...

2 Answers

Old Maytag washer LA182 motor replacement

I need to know if the motor came with a wiring diagram when it was purchased or did it just come by itself. You may have to learn how to read the wiring diagram that is stored inside the control panel.

Jun 09, 2008 | Maytag Atlantis MAV6000 Top Load Washer

1 Answer

Hoover 700LB top loading washing machine

there should be a wiring diagram on board in an envelope or taped somewhere you can get one from sears too

Dec 09, 2006 | Hoover HTC243 Top Load Washer

Not finding what you are looking for?
Hoover HTC243 Top Load Washer Logo

Related Topics:

137 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hoover Washing Machines Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Gerry Harvey
Gerry Harvey

Level 3 Expert

1456 Answers

Chris Hall
Chris Hall

Level 3 Expert

842 Answers

Are you a Hoover Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides