Question about Sharp 19C140 19" TV

1 Answer

Can't find on-off switch

I have the set apart. I can't find the On-Off switch. (pushbutton) It came out, so I took the set apart to put it back in place. I am unable to find it.

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 297 Answers

Get to dealer for repair or short it and operate by extension cord with a switch. Common ordeal for many Philips CRT users in the past years.

Damn breakable switches these days.

Posted on Apr 17, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

4 Answers

35GT740 television


Have you tried to unplug the TV set for a half hour or so? If not see if that helps reset the set. If that does not work, make sure that none of the front panel channels buttons on the front of the TV set is not pushed in and stuck. Or if all this is checked and the TV set still scrolls, there is a problem in the remote sensor, or the front panel board will need to be replaced. Good Luck

Sep 10, 2007 | RCA 24V511T 24" TV

1 Answer

Denon avr 95


Try mouser.com and search on tact switches. You will have to look at the datasheets to find one with the correct dimensions, normally shown in mm and inches. With two leads it is a SPST type switch and very likely "momentary". The amount of pressure it takes to close the switch is not very important but if it is not close to the original it will have a different feel. That should give you enough info to hopefully get what will work for you... good luck!

Dec 13, 2013 | Denon Audio Players & Recorders

1 Answer

I took my kitchenAid stand mixer (md# KSM5PSAC) apart to replace the plastic gear inside of it. When I put it back together it would not start. I took it back apart took a good look at all the connections,...


You need to either re-time the speed control switch at the back or replace it. If it worked great before then it is just an adjustment to get it back to running correctly. YouTube viseo available for timing the switch

Aug 06, 2013 | KitchenAid K45SS Classic Stand Mixer

1 Answer

Reset button or Fuse on my Infinity?


Ok, I took it apart, cleared the clog out, and put it back together. It wouldn't switch to "carpet". Got no answer on my question. Took it apart again, only I went further. Took apart the bottom - brush out, all inside bottom parts out, cleaned all that part of vac. No clogs down there. Ran the carpet/bare floor switch back and forth several times while I had it apart. Put it all back together and it worked fine. Still didn't find a fuse or reset button...

Jan 09, 2010 | Vacuums

1 Answer

Same symptoms


There is a safety switch to make sure you can not power the unit while it is apart. Sometimes this switch will break when you open the unit. Bottom line most manufactures if electric tools and appliances do not want tou screwing with their stuff.

Sep 12, 2009 | Toro Blowers Rake and Vac - Electric...

3 Answers

2000 5.3 silverado pushbutton 4wd wont work


I would try to replace the switch. I believe that chevy had a bunch of problems with the 4x4 switch. I had a message on the display the something was defective with the 4 wheel drive, and it just ended up being the darn switch. Hope this helps.

Feb 17, 2009 | 2000 Chevrolet Silverado 1500

1 Answer

How to remove main pushbutton switch from asko d1716 dishwasher


Hi I read your enquiry of how to remove the pushbutton swith.

You have to open the door, and remove the back panel of the door to release the front protecting cover panel. This is the only way to release the pushbutton. Do not forget to disconect the mains to avoid an electric shock.

Hope I have been of help

Nevd Fixya.

Feb 15, 2009 | Asko D1716 Built-in Dishwasher

2 Answers

My Rainbow stopped running


I took my unit apart to clean it. I was careful to put it back the same way. Now it won't start.

Jul 07, 2008 | Rainbow E series Canister Wet/Dry Vacuum

1 Answer

Tv switching back and forth from three seperate channels, cant get it to stop on any!


The only thing I know of that can do what you are seeing is if something has spilled into the set and has contaminated the pushbuttons under the volume/channel buttons. If the Channel Up pushbutton has fluid in and around it then it can conduct and the microprocessor thinks you are telling it to go up through the channels. The only way to fix that would be to disassemble the set and pull out the PC board which has the pushbuttons on it and clean or replace them. If you do not have experience working inside TV's then allow a qualified tech to handle it for you.

Jul 13, 2007 | RCA F32450 32" TV

Not finding what you are looking for?
Sharp 19C140 19" TV Logo

Related Topics:

44 people viewed this question

Ask a Question

Usually answered in minutes!

Top Sharp Televison & Video Experts

The Knight
The Knight

Level 3 Expert

74198 Answers

Jaime Hernandez

Level 3 Expert

2318 Answers

Cindy Wells

Level 3 Expert

5124 Answers

Are you a Sharp Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...