Question about Dishwashers

1 Answer

Is this hot or cold feed

Is the whirlpool/ikea DWH b10 hot or cold feed

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 423 Answers

This dishwasher should be connected to the hot water line under the sink. If it is connected to the cold line, you will have very poor cleaning. The hot water should be 120 degrees (F) minimum and less than 140 degrees.


Posted on Apr 18, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Just need to know how to operate DWH B80


Hi Wendy the link below has two user manual downloads on it, I hope you find what you're looking for....CHEERS..
http://lastmanuals.com/manual/WHIRLPOOL/DWH-B80-W

Mar 24, 2016 | Whirlpool DWH B80

6 Answers

Whirlpool DWH B10 - under IKEA


Try checking this link for the user manual http://www.serviceforce.co.uk/pdf_search.asp

Hope that helps..........

Jul 24, 2008 | Dishwashers

1 Answer

Whirlpool dwh b10 stuck on rinse cycle


sounds like your heating element has open circuit duff fit a new element should work fine

Sep 26, 2012 | Washing Machines

1 Answer

DWH B10 F3 - no heat. Stops at rinse and beeps + flashes 3 times


Hello

The majority of dishwashers are not connected to hot water from the mains but heat up the water internally using the heating element, located in the tub of the dishwasher, controlled by a thermostat. When the dishwasher has a fault with heating, the program will run but not complete and will show an error code on the display panel. Dishes won't be cleaned properly and the detergent won't dissolve.

If your dishwasher does bring in hot water externally from the mains to check the water is warm and there are no problems with the inlet. If the dishwasher heats internally then it is most likely a faulty heating element or thermostat. A fault like this will usually require a replacement part and a repair, but you can check the heating element with a voltmeter to ensure that it is the cause of the problem before calling out for a service engineer.

Sep 10, 2011 | Whirlpool Dishwashers

1 Answer

Whirlpool dwf b10 manual


Try this site

http://www.whirlpool.co.uk/support_instructions-for-use_instructions-for-use.content.html

then enter in DWH B10 and you should be able to download a PDF manual

Oct 12, 2010 | Dishwashers

1 Answer

Whirlpool / IKEA Dishawasher DWH B10 - castor wheel


make sure there aren't any screws through tabs at the top front of the washer that fastened it to the counter top.

Jan 04, 2010 | Dishwashers

1 Answer

Washing machine not heating water


yes it will work but unless you have hot water going into the machine there will never be hot water there but you can just use it with cold water will not hurt anything just no hot water

Mar 09, 2009 | Whirlpool Ultimate Care II LSQ9549L Top...

1 Answer

WHIRLPOOL AWO/D 5726 - cold water feed only?


Most washers now made in the u/k, are cold fill only, but if the new washer is hot and cold fill, and you only have a cold supply, then it will tell you in the installation guide how to connect it to use it from cold only.
Plz rate my solution.
Thanks.

Jan 08, 2009 | Washing Machines

1 Answer

Whirlpool dishwasher installation


FOUND IT!!!!!
There is a white plastic screw in front of the dishwasher to estend the back leg!!!!!
Whirpool people are crazy!!!!
Max

Aug 17, 2008 | Dishwashers

Not finding what you are looking for?
Dishwashers Logo

Related Topics:

508 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dishwashers Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Owen Barnes

Level 3 Expert

867 Answers

Brad Brown

Level 3 Expert

15628 Answers

Are you a Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...