Question about Hitachi 60EX01B 60" Rear Projection Television

2 Answers

No Power With the back off - just pluging it in, it soulds like it will come on.the green leds will light - after a few sec they all go bright then it shuts down - the protect LED starts to blink. the hot checks good,thank you for any help. if this was an ceronix or kortek monitor I would not be here (HA! HA!) Thank you

Posted by on

  • result1 Sep 21, 2007

    With the back off - just pluging it in, it soulds like it will come on.the green leds will light - after a few sec they all go bright then it shuts down - the protect LED starts to blink.

    the hot checks good,thank you for any help.

    Reseting (leaving the TV off for 3 min 2 days don't work -) it's something on the board cap or something that is connected to the board.
    thought nost of the sets would have common problems like I find in the casinos

×

Ad

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 398 Answers

Most likely, the little blue capacitor next to the horizontal output transistor has shorted and the main B+ fuse is open. This will cause the exact symptoms you are experiencing. This is very common on those Hitachi projection sets and is easily fixed. If you do not have experience locating and replacing bad parts in projection sets, have a qualified tech handle it for you.

Posted on Sep 22, 2007

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

    Sergeant:

    An expert that has over 500 points.

  • Master
  • 461 Answers

Try to reset your monitor. Turn off, remove the power supply from the socket leave it for 30 mins and turn it on again.

Posted on Sep 21, 2007

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How can I increase brightness on head light of my super splendor model 2011?


aim the light correctly
indicates that it aimed to high up into the he trees instead on along the ground

Nov 29, 2017 | Cars & Trucks

1 Answer

Lg laptop not power on only blinking 16 times then stop green led indicator light on when i press the power bottom it will not turn on and green light indicator goes out.?


Did you try a hard stop? Hold the power button down for five to ten secs until all functioning stops, wait five secs then try to power it back up? I'm no laptop expert, but that has helped me a few times here and there.

Aug 24, 2016 | LG Computers & Internet

1 Answer

Broksonic Flat Panel TV, tried to turn back on TV and Green LED light is blinking and screen pops up a few sec with white and colored lines and the turns off


These blinks [flashes] are fault indication (Error Codes). From the number of blinks occur at one time switch ON, you can get an idea about the faulty circuit section inside it. This will make repair easy. These are called blinking codes. Make sure about the exact number of blinking of the standby/power LED, by switching On & OFF the set, for at least two times. Count it carefully. If you wish to get some details, check the site linked here. It has details about blinking codes, and fault locating procedure, to many popular brand TVs and other devices. http://electronicshelponline.blogspot.com/
Blinking codes details to many popular brand TVs are given. Surf the site with patience. If blinks continue without any pause, the main board is faulty.

Oct 21, 2014 | Broksonic Televison & Video

1 Answer

Toshiba regaza 37rv635db wont turn on


seems like capacitor problem, chack them and if thay have exploded replace them.

Aug 25, 2013 | Toshiba 37RV635DB Regza 37-inch Widescreen...

1 Answer

No picture, when powering up the light will turn yellow, them the t.v powers up and can hear sound but no picture, and then hear a click and light flashes green.


First turn on,do the power LED light stable?Few sec.Power LED and LED OPC flashes?This very common on Sharp tv,tries power off/on at 4 or 5 each time it flashes,well power up have backlight on and it work.After this doesn't work than ur Tuner Signal board it dead.

Feb 03, 2010 | Sharp Aquos LC-42D62U 42 in. LCD HDTV

2 Answers

Wiring info


Most Mobo's have printing next to the places that are jumpered or pluged into. The ones you need sould be close to the edge of the mobo, that is close to the front {power button} side.

May 30, 2008 | E-Machines (308714) Motherboard

2 Answers

No picture, but power is on...


How many times does the POWER led blink per sec? (dont worry about the OPC)

2x = power supply (not as expensive to fix)
3x = Main board (expensive to fix)

Oct 20, 2007 | Sharp Aquos LC-42D62U 42 in. LCD HDTV

Not finding what you are looking for?
Hitachi 60EX01B 60" Rear Projection Television Logo

Related Topics:

97 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hitachi Televison & Video Experts

Jaime Hernandez

Level 3 Expert

2336 Answers

The Knight
The Knight

Level 3 Expert

75462 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Are you a Hitachi Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...